K RCHER T 5 T-Racer Surface Cleaner Instruction Manual

: June 3, 2024
: K RCHER

K RCHER T 5 T-Racer Surface Cleaner

General notes

Read the original instructions before using the device for the first time and act in accordance with it. Keep the original instructions for future reference or for future owners.

Illustrations and descriptions in these operating instructions

Illustrations and descriptions in these operating instructions may differ from the scope of delivery and equipment for your T-Racer.
Note
Subject to technical changes without notice

Intended use

The T-Racer can be used with all Kärcher Home & Garden high-pressure cleaners of class K2. Detailed information on the device class is provided in the operating instructions for your high-pressure cleaner. For devices manufactured up to 1991 you require an additional adapter (see “Accessories and spare par

Environmental protection

The packing materials can be recycled. Please dispose of packaging in accordance with the environmental regulations.
Electrical and electronic devices contain valuable, recyclable materials and often components such as batteries, rechargeable batteries or oil, which – if handled or disposed of incorrectly – can pose a potential danger to human health and the environment. However, these components are required for the correct operation of the device. Devices marked by this symbol are not allowed to be disposed of together with the household rubbish.
Working with detergents may only be performed on watertight surfaces with connection to the waste water sewage system. Do not allow detergent to enter waterways or the soil

Notes on the content materials (REACH)

Current information on content materials can be found at: www.kaercher.de/REACH

Accessories and spare parts

Only use original accessories and original spare parts. They ensure that the appliance will run fault-free and safely.Information on accessories and spare parts can be found at www.kaercher.com.

Scope of delivery

Check the contents for completeness when unpacking. The scope of delivery for your equipment version is shown on the packaging. Please contact your dealer if any accessories are missing or in the event of any shipping damage.

Safety instructions

CAUTION

Do not use the device when persons are in the vicinity of the cleaning head.
Switch the high-pressure cleaner off and disconnect the T-Racer from the high-pressure gun after finishing cleaning work and before performing any work on the T-Racer.
Do not trigger the high-pressure jet at the high-pressure gun until the T-Racer is on the surface to be cleaned.
Recoil danger. Keep proper footing and hold the highpressure gun and extension tube firmly.
Maximum water temperature 60°C (please observe the instructions for your high-pressure cleaner). Note
Be sure to always adhere to the safety instructions for your high-pressure cleaner and the locally applicable regulations and directives

Symbols on the device

| DANGER Risk of injury! Never reach under the edge of the T-Racer during operation
---|---
HARD| For durable surfaces, e.g. tiles, concrete, For durable surfaces, e.g. tiles, concrete,
SOFT| For sensitive surfaces, e.g. wood

Device description

For the illustrations, refer to the graphics page
Illustration A

① Extension tube
② Rotor arm height adjustment
③ Casing
④ Bayonet connector with union nut
⑤ Handle
⑥ High-pressure nozzle
⑦ Roto

Etxension tube installation

Note

Ensure that the device components are tightly connected on installatio

Plug the bayonet into the mounting.
Turn the extension until it latches into place.
Tighten the union nut.
Repeat the procedure for all further extension tube

Initial startup

Selection of the high-pressure nozzles

Using the appropriate high-pressure nozzles is a prerequisite for fault-free operation.

Note
These are to be selected according to the flow rate (l/ min). Information on the flow rate is provided in the operating instructions or on the type plate of the high-pressure cleaner

Note

The yellow high-pressure nozzles are already fitted

Flow rate l/min (l/h)| High pres- sure class (e.g.)| Colour of the high-pressure nozzles
---|---|---
Less than 5.8 (348)| K2 – K3| Green
5.8 (348) – 7.5 (450)| K3 – K5| Grey
Greater than 7.5 (450)| K6 – K7| Yellow

Operation

Note
The extension tubes can be used with all Kärcher accessories

Note
For optimum cleaning results, do not operate the highpressure cleaner in the Eco mode

Cleaning floors

Remove coarse dirt from the surface to be cleaned (e.g. by sweeping) before using the device to avoid damage to the T-Race

ATTENTION
Damage to the rotor arm

The rotor arm can be damaged if it hits edges and corners. Do not move the device over free-standing corners and edges

Illustration C

Note

The T-Racer is not suitable for scraping or scrubbing.
Test the device on an inconspicuous area before using on sensitive surfaces, e.g. wood.
Do not allow it to remain in one area, but keep it in motion.

Attach the T-Racer to the high-pressure gun using the extension tube.
Illustration B

a. Press the extension tube onto the bayonet connector of the high- pressure gun.
b. Turn the extension tube by 90° until it latches into place.
c. If necessary, repeat the procedure for further connections.
Adjust the rotor arm height adjustment. according to the surface to be cleaned.
Unlock the lever of the trigger gun.
Pull the lever of the trigger gun. The device switches on.
Clean the floor surface by guiding the T-Racer over the floor surface without exerting excessive pressure.

Cleaning wall surfaces

Attach the T-Racer directly to the high-pressure gun.
a. Press the bayonet connector of the T-Racer into the connection on the high-pressure gun and then turn by 90° until it latches into place.
b. Tighten the union nut if present.
Clean the wall surface

Rotor arm height adjustment

The clearance of the high-pressure nozzles to the surface to be cleaned can be adjusted via the rotor arm height adjustment. Adjust the rotor arm height adjustment. according to the surface to be cleaned.

Illustration D

For powerful cleaning of stubborn soiling on durable surfaces, e.g. tiles, concrete, stone:

Set the rotor arm height adjustment to “HARD”.
For cleaning sensitive surfaces:
Set the rotor arm height adjustment to “SOFT”

After use

Rinse off the device with a gentle water stream after use.

Detach the T-Racer and any extension tubes from the high-pressure gun.
Rinse off the T-Racer with the high-pressure gun (without accessories) or wipe down with a damp cloth

Storage

Store the device in a frost-protected place.

Care and service

Removing/installing the nozzles

The described procedure applies to all nozzles on the device.

Illustration E

Remove the clip.
Pull the high-pressure nozzle out.
Fit the high-pressure nozzle.
Fit the clip.

Cleaning the high-pressure nozzle

Remove the high-pressure nozzle.
Flush the high-pressure nozzle with clear water in both directions. Replace a damaged high-pressure nozzle where necessary.
Install the high-pressure nozzl

Troubleshooting guide

High-pressure cleaner not building up pressure or pulsing High-pressure nozzles clogged or damaged.

Remove the high-pressure nozzles.
Check the high-pressure nozzles for clogging and clean if necessary.
Check the high-pressure nozzles for damage and replace if necessary.
Flush the T-Race with clear water without the nozzles fitted. Install the high-pressure nozzles. Incorrect high-pressure nozzle selected. The device only provides optimum cleaning results when used with the appropriate high-pressure nozzles!
Select the appropriate high-pressure nozzles according to the high-pressure cleaner used.
Install the high-pressure nozzles.

Warranty

The warranty conditions issued by our relevant sales company apply in all countries. We shall remedy possible malfunctions on your appliance within the warranty period free of cost, provided that a material or manufacturing defect is the cause. In a warranty case, please contact your dealer (with the purchase receipt) or the next authorised customer service site. (See overleaf for the address)

|

www.kaercher.com/dealersearch
Alfred Kärcher SE & Co. KG
Alfred-Kärcher-Str. 28-40
71364 Winnenden (Germany)
Tel.: +49 7195 14-0
Fax: +49 7195 14-2212

|
---|---|---