Rusta 907512160101 Floor Standing Fan Instruction Manual
- June 1, 2024
- RUSTA
Table of Contents
Rusta 907512160101 Floor Standing Fan
Specifications
- Power : max. 46.20 W
- Weight : Not specified
- Protection class : Not specified
- Noise level : max. 62 dB
- Maximum fan flow rate : 58.40 m3/min
- Fan power input : 46.20 W
- Service value : 1.26 (m3/min)/W
Product Overview
Thank you for choosing to purchase a product from Rusta!
Safety Instructions
WARNING! If these instructions are not followed, an accident may lead to serious personal injury or property damage.
Get Started! Assembly Instructions
- Rotate the washer and the L-screw off the lower column.
- You can assemble this fan in 3 different heights.
Use
Control Panel and Remote Control
The fan can be operated both from the control panel and using the remote control.
The functions of the remote control buttons are the same as the functions of the buttons on the control panel.
Operation
- Plug the supply cord into a suitable socket. The indicator screen shows a white light.
- Press the ON/OFF button to start the fan.
- Press the speed button to select the desired wind speed. There are three settings available.
Right of Complaint
By law, the product must be returned to the place of purchase along with the original receipt in the event of a complaint.
Environment and Recycling
When the product is used up, leave it for recycling according to local waste disposal regulations. Do not dispose of the product with normal household waste.
Model Information
Description: Floor-standing fan 2 in 1
- Maximum fan flow rate : 58.40 m3/min
- Fan power input: 46.20 W
- Service value : 1.26 (m3/min)/W
- Standby power consumption: 0.45 W
FAQ
- Q: How do I adjust the height of the fan?
- A : You can assemble this fan in 3 different heights by rotating the washer and L-screw off the lower column.
- Q: Can I operate the fan without the remote control?
- A : Yes, you can operate the fan both from the control panel and using the remote control
Thank you for choosing to purchase a product from Rusta
Read through the entire manual before installation and use!
PRODUCT OVERVIEW
- A Front grille
- B Blade nut
- C Blade / Blad
- D Plastic nut
- E Rear grille
- F Motor housing
- G Control box
- H Supply cord
- I Column fastening bolts
- J Upper column
- K Lower column
- L Base
- M Washer
- N L-screw
- O Screw for grille clip
- P Remote control
SPECIFICATIONS
SAFETY INSTRUCTIONS
- Make sure that the product is completely assembled before using it for the first time.
- Do not turn on the power before the product is completely assembled. The product must only be used in the upright position, never horizontally or when it is lying on its side.
- The product should only be connected to a 220–240 V~, 50–60 Hz electrical outlet.
- Place the product where there is no risk of people tripping over its mains lead.
- This product is intended for indoor use only.
- The product is only intended for indoor use in a dry, clean environment.
- Never position the product in such a way that it might fall into water or other liquid.
- Never use it in the bathroom or in humid environments.
- Never use the product in areas where explosive gases or substances are stored.
- Never position the product where it could come into contact with hot surfaces.
- Never insert foreign objects through the safety grille or housing. Doing so could result in an electric shock or a mechanical hazard.
- Make sure that there is no risk of long hair or curtains being sucked into the air intake of the fan.
- Do not expose the product to direct sunlight or high temperatures from sources such as heaters and fireplaces.
- Never turn the product off by pulling the plug out of the wall socket. Turn off the product using the power button and then unplug it from the wall socket.
- Always unplug the product from the wall socket when it is not in use. Always grip the plug when unplugging, never pull the mains lead.
- Never lay the mains lead over hot surfaces, sharp edges or corners.
- Unplug the product from the wall socket immediately if you detect a burning smell, hear an unusual sound or if the product starts operating abnormally.
- The product may be used by children of 8 years and older and by persons with reduced physical, sensory or mental capability or lack of experience and knowledge provided they have been given supervision or instruction concerning use of the product in a safe way and understand the hazards involved.
- Never let children play with the product.
- Persons (including children) whose physical, sensory or mental capability or lack of experience and knowledge means that they cannot use the product in a safe way must not use it without supervision or instruction.
- Never attempt to repair or modify the product in any way.
- Cleaning and user maintenance must not be performed by children without adult supervision.
- Never use the product if it does not work properly or if the housing, mains lead or plug is damaged in any way.
- If the supply cord has been damaged, it must only be replaced by the manufacturer, authorised service facility or qualified tradesman in order to avoid a hazard.
WARNING!
If these instructions are not followed, an accident may lead to serious personal injury or property damage.
GET STARTED!
ASSEMBLY INSTRUCTIONS
- Rotate the washer and the L-screw off the lower column.
- You can assemble this fan in 3 different heights. Table desk fan: Put the control box directly into the base and fix it by tightly screwing the washer and the L-screw at the back of the base.
- Floor standing fan – full height: Put the lower column into the base and fix it by tightly screwing the washer and the L-screw at the back of the base. Put the upper column and control box above and use the column fastening bolts to tighten the connection. Floor standing fan – mid-height: The same procedure as for full height but do not use the upper column during assembly.
- Rotate off the grille fastening screw.
- Align and place the rear grille onto the motor housing. Fix it by tightening the grille fastening screw.
- Place the fan blade onto the motor shaft by aligning the groove with the shaft pin. Fix the blade by tightening the blade fastening screw. Check that the fan blade can rotate freely by turning it with your hand.
- Align the front and rear grille.
- Fasten the front and rear grilles by tightening the screw on the grille clip.
USE
CONTROL PANEL AND REMOTE CONTROL
- ON/OFF button
- Speed button
- Mode selection button
- Timer setting button
- Oscillation button
- Mode indicator light
- Indicator screen
The fan can be operated both from the control panel and using the remote control. The functions of the remote control buttons are the same as the functions of the buttons on the control panel.
OPERATION
Plug the supply cord into a suitable socket. The indicator screen shows a white light.
- Press the ON/OFF button to start the fan.
- Press the speed button to select the desired wind speed. There are three settings indicated by the icons on the indicator screen: 1 = low speed; 2 = medium speed; 3 = high speed
- Press the mode selection button to set the desired operation mode from normal, natural and sleep mode. When the fan is in normal mode, the indicator light turns red. When in natural mode, the indicator light turns green. When in sleep mode, the indicator light turns off.
- TIMER: Press the timer button to set the number of hours the fan will automatically switch off after. You can set it from 0 to 9 hours. The set value will be shown on the indicator screen. When the screen displays “0”, the timer is cancelled. When the selected number of hours has passed, the fan will switch off automatically.
- Oscillation: Press the oscillation button to start oscillation for widespread air distribution. Press the button once more to stop oscillation.
- Tilting angles: By pushing the fan-guard, you can adjust the fan to the preferred elevation.
To use the remote control, please note:
- 2 x AAA batteries are required.
- Ensure that the batteries are inserted into the battery compartment in the correct direction.
- Do not mix battery types.
- When the batteries need replacing, make sure that both batteries are changed at the same time.
- If the remote control will not be in use for a long time, remove the batteries from the remote control.
- During operation, point the remote control towards the LED display at the front of the fan and ensure that there is no obstruction in the path of the signal.
- Handle the remote control carefully. Do not drop or throw it.
CARE AND CLEANING
- Before cleaning and assembling the fan, it must be unplugged.
- To ensure adequate air circulation to the motor, keep the vents at the rear of the motor free of dust. Do not disassemble the fan to remove dust.
- Wipe the exterior parts with a soft cloth soaked in a mild detergent.
- Do not use any abrasive detergent or solvents to avoid scratching the surface. Do not use any of the following as a cleaner: gasoline or thinner.
- Do not allow water or any other liquid into the motor housing or interior parts.
- When storing your fan, make sure to place it in a dry environment. To reduce dust and particle exposure, it is best to cover your fan – especially in the off-season period.
RIGHT OF COMPLAINT
By law the product must be returned to the place of purchase along with the original receipt in the event of a complaint. The user is liable for any damage to the product that is caused by not using the product for its intended purpose or by not following this user manual correctly. The right of complaint will not apply in these instances.
ENVIRONMENT AND RECYCLING
When the product is used up, leave it for recycling according to local waste disposal regulations. Note that the product must not be disposed of with normal household waste.
INFORMATION TO IDENTIFY THE MODEL TO WHICH THE INFORMATION RELATES TO: 907512160101
Customer Service Rusta
- Consumer contact: Rusta Customer Service, Box 5064, 194 05 Upplands Väsby, SWEDEN
- Website: www.rusta.com
- E-mail: customerservice@rusta.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>