Shark S7201 Steam Blaster User Guide
- June 17, 2024
- Shark
Table of Contents
Shark S7201 Steam Blaster
Specifications:
- Product Model: S7201 Series
- Recommended Surfaces: Laminate, hardwood, vinyl, delicate surfaces, marble, tile, stone
- Settings: Light, Normal, Deep
- Warranty: One (1) Year Limited Warranty
Product Usage Instructions
Steam Mop Assembly:
- Insert the handle into the mop body until it clicks into place.
- Unplug the steam mop before refilling the water tank.
- To refill the water tank, pull the lid down and use the filling flask to add distilled water up to the Max Fill line. Close the tank lid firmly.
Using Your Steam Mop:
- Sweep or vacuum floors before mopping.
- Plug in the unit and recline the handle.
- Press the Mode button to select a setting (Light, Normal, Deep).
- Wait for 5 seconds before scrubbing to let the steam blast penetrate the mess.
After Use and Storage:
- Press the mode button until in Standby mode. Unplug and place the steam mop in an upright position to cool.
- Once cooled, remove the pads by pulling them off the discs.
- Empty the water tank after cooling and release of steam.
- Store the steam mop in an upright position in a dry, protected area.
FAQ:
-
What surfaces are suitable for cleaning with this steam mop?
The steam mop is suitable for laminate, hardwood, vinyl, delicate surfaces, marble, tile, and stone. -
How do I know when to change the setting on the steam mop?
You can change the setting by pressing the Mode button to cycle through Light, Normal, Deep, and Standby modes. The recommended usage for each setting is provided in the manual.
QUICK START GUIDE
Please be sure to read and save the warnings on the other side before using your unit.
STEAM MOP ASSEMBLY
- Insert the handle into the mop body until it clicks into place. (fig. 1)
- Place Dirt Grip® Pads on the floor with the rings facing up. Align the mop head so the indents on the rotating discs are directly above the rings, then lower the head onto the pads, pressing until secure. (fig. 2)
- Unplug the steam mop before refilling the water tank.
- To open the water tank, pull the lid down. Use the filling flask to add distilled water up to the Max Fill line, then close the tank lid firmly. (fig. 3)
STEAM BLASTER
- To target tough messes with an extra burst of cleaning power, move the front of the nozzle 2 to 4 inches from the mess, then press and hold the Steam Blaster® button as needed. (Hold longer for the toughest messes.)
- Before scrubbing, wait 5 seconds to let the steam blast penetrate the mess.
Tip : For more difficult messes, allow 20 seconds or more. Note: While the Steam Blaster is blasting steam, steam does not also emit from the pads.
INTELLIGENT STEAM CONTROL
Note: Press to cycle through modes (Light, Normal, Deep, Standby). In Standby, all LEDs will flash.
USING YOUR STEAM MOP
- Sweep or vacuum floors before mopping.
- Plug in the unit and recline the handle.
- Press the Mode button to select a setting. The pads will start spinning. Wait 30 seconds for the unit to begin producing steam.
- Mop with a forward and backward motion.
- When finished mopping, press the Mode button until in Standby; the lights will blink.
- Lift the handle to stand the mop upright, then unplug the cord. Allow the mop to cool completely (2 – 3 mins), then pull the pads off the discs.
NEVER leave the steam mop with damp pads on any floor for an extended period.
AFTER USE AND STORAGE
- Press the mode button until the indicator lights below start to blink, indicating that you are in Standby mode. Unplug the cord from the outlet and place the steam mop into the upright position. Let it cool. (fig. 4)
- When the pads have cooled completely, remove them by pulling them off the discs. (fig. 5)
- After the unit has cooled and the steam has been released, empty the water tank before storing. Open the tank lid and pour the water out into a sink or bathtub. After all the water has drained out, close the lid.
- To store the steam mop, wait until after it has cooled and the steam has been released. Lock the steam mop in an upright standing position by raising the handle until the pole is standing straight up, perpendicular to the ground. With the unit locked in the upright standing position, store it in a dry, protected area (e.g., in a closet or the corner of a room) until next use.
ONE (1) YEAR LIMITED WARRANTY
The One (1) Year Limited Warranty applies to purchases made from authorized
retailers of SharkNinja Operating LLC. Warranty coverage applies to the
original owner and to the original product only and is not transferable.
SharkNinja warrants that the unit shall be free from defects in material and
workmanship for a period of one (1) year from the date of purchase when it is
used under normal household conditions and maintained according to the
requirements outlined in the Owner’s Guide, subject to the following
conditions and exclusions:
What is covered by this warranty?
- The original unit and/or non-wearable parts deemed defective, in SharkNinja’s sole discretion, will be repaired or replaced up to one (1) year from the original purchase date.
- In the event a replacement unit is issued, the warranty coverage ends six (6) months following the receipt date of the replacement unit or the remainder of the existing warranty, whichever is later. SharkNinja reserves the right to replace the unit with one of equal or greater value.
What is not covered by this warranty?
- Normal wear and tear of wearable parts (such as Shark Cleaner, Pad, etc.), which require regular maintenance and/or replacement to ensure the proper functioning of your unit, are not covered by this warranty. Replacement parts are available for purchase at sharkaccessories.com.
- Any unit that has been tampered with or used for commercial purposes.
- Damage caused by misuse (e.g., vacuuming up water or other liquids), abuse, negligent handling, failure to perform required maintenance, or damage due to mishandling in transit.
- Consequential and incidental damages.
- Defects caused by repair persons not authorized by SharkNinja. These defects include damages caused in the process of shipping, altering, or repairing the SharkNinja product (or any of its parts) when the repair is performed by a repair person not authorized by SharkNinja.
- Products purchased, used, or operated outside North America.
How to get service
If your appliance fails to operate properly while in use under normal
household conditions within the warranty period, visit sharkclean.com/support
for product care and maintenance self-help. Our Customer Service Specialists
are also available at
1-800-798-7398 to assist with product
support and warranty service options, including the possibility of upgrading
to our VIP warranty service options for select product categories. So we may
better assist you, please register your product online at
registeryourshark.com and have the product on hand when you call. SharkNinja
will cover the cost for the customer to send in the unit to us for repair or
replacement. A fee of $25.95 (subject to change) will be charged when
SharkNinja ships the repaired or replacement unit.
How to initiate a warranty claim
You must call 1-800-798-7398 to
initiate a warranty claim. You will need the receipt as proof of purchase. We
also ask that you register your product online at registeryourshark.com and
have the product on hand when you call, so we may better assist you. A
Customer Service Specialist will provide you with return and packing
instruction information.
How state law applies
This warranty gives you specific legal rights, and you also may have other
rights that vary from state to state. Some states do not permit the exclusion
or limitation of incidental or consequential damages, so the above may not
apply to you. This steam mop has a polarized plug (one blade is wider than the
other). As a safety feature, this plug will fit into a polarized outlet only
one way. If the plug does not fit fully into the outlet, reverse the plug. If
it still does not fit, contact a qualified electrician. DO NOT attempt to
defeat this safety feature. It is not recommended to use an extension cord
with this product.
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY:
GENERAL WARNINGS
WHEN USING YOUR SHARK® STEAM & SCRUB, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED, INCLUDING THE FOLLOWING:
-
DO NOT leave the steam mop unattended when plugged in. ALWAYS unplug the power cord from the electrical outlet when not in use and before servicing.
-
DO NOT use with damaged cord or plug. If steam mop is not working as it should or has been dropped, damaged, left outdoors, or dropped into water, return it to SharkNinja Operating LLC for examination and repair. Incorrect reassembly or repair can cause a risk of electrical shock or injury when the steam mop is used.
-
To protect against a risk of electric shock, DO NOT immerse the steam mop in water or any other liquids.
-
DO NOT handle the plug or steam mop with wet hands or operate it without wearing shoes.
-
DO NOT pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners. DO NOT run steam mop over cord. Keep cord away from heated surfaces.
-
DO NOT unplug by pulling on power cord. To unplug, grasp the plug not the power cord. DO NOT use extension cords or outlets with inadequate current-carrying capacity.
-
Unplug before servicing.
-
ALWAYS make sure the steam mop is UNPLUGGED when not in use.
-
NEVER fill the steam mop or attach the mop head when the steam mop is plugged into an electrical outlet. Unplug from the electrical outlet and allow to cool before you fill the mop, or attach or remove the head.
-
When cleaning the exterior of the steam mop, unplug the power cord from the electrical outlet and clean the steam mop with a dry or damp cloth. DO NOT pour water or use alcohol, benzene, or paint thinner on the steam mop.
-
To avoid circuit overload, DO NOT operate another appliance on the same socket (circuit) as the steam mop.
-
To avoid scalding injuries, ALWAYS unplug and allow the steam mop to cool before removing or changing mop heads, accessories, or Dirt Grip® pads.
USE WARNINGS -
When in use, NEVER turn the steam mop over on its side or direct steam toward people, pets or plants.
-
Use the system only for its intended use.
-
DO NOT use for space-heating purposes.
-
DO NOT use outdoors.
-
DO NOT allow the steam mop to be used by children. Close attention is necessary when used near children, pets, or plants.
-
Use only as described in this owner’s guide.
-
Use only manufacturer’s recommended accessories.
-
DO NOT put any objects into the steam nozzle openings. Discontinue use if the steam nozzle is blocked.
-
DO NOT put hands or feet under the steam mop. It gets very hot.
-
Use ONLY on flat, horizontal surfaces. DO NOT use on walls, counters, or windows.
-
DO NOT use on leather, wax-polished furniture, synthetic fabrics, velvet, or other delicate, steam-sensitive materials.
-
DO NOT add cleaning solutions, scented perfumes, oils, or any other chemicals to the water used in the steam mop as this may damage it or make it unsafe for use. If you live in a hard-water area, we recommend using distilled water in your steam mop.
-
NEVER leave any Dirt Grip® pads in one spot while using or storing for an extended period, as this may damage your surfaces.
-
You can release the Dirt Grip® pads after you have unplugged the steam mop and allowed it to cool.
-
Extreme caution should be exercised when using the steam mop to clean stairs.
-
NEVER use steam mop without the Dirt Grip® pads attached.
-
Keep your work area well lit.
-
Store steam mop indoors in a cool, dry place.
-
Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.
-
DO NOT carry the steam mop while in use.
-
The steam emitted from the steam mop is very hot and may cause scalding. Please use caution when using the steam mop.
-
DO NOT use on unsealed wood or unglazed ceramic floors. On surfaces that have been treated with wax and on some unwaxed floors, the sheen may be removed by the heat and steam action.
-
ALWAYS test an isolated area of the surface to be cleaned before proceeding. We also recommend that you check the use and care instructions from the floor manufacturer.
-
DO NOT scrub any one area for an extended period.
-
DO NOT use the steam mop without attaching the Dirt Grip® pads and adding water to the water tank. When you use the steam mop for the first time, it might take longer than the normal 30 seconds to start steaming.
-
DO NOT use on unsealed wood or unglazed ceramic floors. On surfaces that have been treated with wax and on some unwaxed floors, the sheen may be removed by the heat and steam action. Test an isolated area of the surface to be cleaned before proceeding. Check the use and care instructions from the floor manufacturer.
-
To prolong the life of your steam mop, we recommend using distilled water. Add ONLY water to the tank. Chemicals or cleaning solutions (including vinegar) may damage the steam mop and could be unsafe for you and your family.
-
The liquid or steam must not be directed towards equipment containing electrical components, such as the interior of ovens.
READ AND SAVE THESE INSTRUCTIONS VISIT sharkclean.com/support OR SCAN HERE
Ordering Additional Accessories: You can purchase replacement Dirt Grip® pads, dusting pads, and other accessories by visiting sharkclean.com.
© 2022 SharkNinja Operating LLC. DIRT GRIP, INTELLIGENT STEAM CONTROL, SHARK,
and STEAM BLASTER are registered trademarks of SharkNinja Operating LLC.
S7201_QSG_One-Sheet_MP_Mv10 @sharkcleaning
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>