niko 552-72002 Wireless Battery Powered Switch Twofold Instruction Manual
- June 16, 2024
- niko
Table of Contents
Manual
552-720X2
Wireless battery-powered switch, twofold, Zigbee®
Description
This twofold wireless battery-powered Zigbee® switch allows you to remotely control wireless Zigbee® devices. It can either be used in a Niko Home Control installation (max. fifty Zigbee® devices) or connected to a third-party Zigbee® system as a standard dimmer switch (ON/OFF/ dimming) via EZ-mode pairing. The switch also supports Touchlink or Find&Bind to pair with up to eight Zigbee® receivers (ON/OFF/dimming) for stand-alone use or decentral networks. The wireless Zigbee® switch is battery powered with a lifetime of at least five years, based on twenty short press actuations a day. The variant with a plastic baseplate (552-72002) is used for wall installation. Fixation is possible with double-sided adhesive tape (included) or screws (excluded). For flush-mounting box installation, use variant 552-72012 together with the metal baseplate (552-720X0) suitable for your region.
Dimensions
Zigbee® network
Install the twofold wireless battery powered Zigbee® switch within 10 m of a Zigbee® receiver. Battery-powered Zigbee® devices act as endpoints and do not support Zigbee® mesh networking. For more information on Zigbee® network principles and signal range, consult guide.niko.eu.
*Also, respect a minimum distance of 2 m between a Zigbee® device (including the smart hub) and another RF transmitter (for example a Wi-Fi device) or devices such as motors, pumps, electronic LED transformers, solar panel inverters, home battery storage ….
Installation
Battery replacement
Stand-alone use
The twofold wireless battery-powered Zigbee® switch (522-720X2) can be used in stand-alone mode without a gateway. In this mode, each control button can be paired with Zigbee® receivers (ON/OFF/dimming). The twofold switch can be paired with up to eight Zigbee® receivers in total, such as a smart Zigbee® 3.0 lamp. Pairing is done via Touchlink or Find&Bind.
Touchlink pairing
Reset all Zigbee® devices if they were previously connected to another Zigbee®
network. See § Reset. For Find&Bind pairing consult
guide.niko.eu
Connected use
- Connected to a Niko Home Control installation
More advanced functionalities become available if you connect this device to your wireless smart hub (552-00001) or wireless bridge (550-00640) using the Niko Home Control programming software or Niko Home app.
Consult guide.niko.eu for more information about the installation and the connected use.
www.niko.eu/article/550-99102 (Windows)
www.niko.eu/article/550-99202 (Mac)
How to connect the Niko device to the Niko Home Control network
- Reset the Niko Zigbee® device if it is already connected to another net- work. See § Reset.
- Follow the onboarding procedure in the Niko Home Control programming software or the Niko Home app to add new Niko Zigbee® devices
- Set the Niko Zigbee® device in EZ-mode by pressing on of the switch ogramming software DASHBOARD CREATE FILL CABINET ADDRESS Upload buttons 3 x within 6 seconds > see the image on ‘EZ-mode pairing’. The blue PROGRAM LED starts blinking for max. 90 seconds
- The Zigbee® device is successfully added to the Niko Home Control installation when the blue PROGRAM LED is ON for 4 seconds and then turns OFF again
2. Connected to a third-party Zigbee® network
The twofold wireless battery-powered Zigbee® switch can be connected to a
third-party network via EZ-mode pairing. Refer to the third-party software or
smartphone app to link a specific button of the battery-powered Zigbee® switch
to an actor within the third-party network. You can also use Find&Bind
pairing. Consult guide.niko.eu and the manufacturer’s manual for more
information on using third-party Zigbee® devices in their network. Note that
specific Niko Home Control functions will not be enabled when Niko Zigbee®
devices are connected to a third-party Zigbee® gateway. See also the
disclaimer at http://www.niko.eu/zigbee.
Online guide
Consult guide.niko.eu for more information about the installation,onboarding, the stand-alone/connected use and troubleshooting.
Troubleshooting
| Problem | Cause | Action |
|---|
The battery- powered switch cannot be found in the Niko Home app or programming software| The power supply of the wireless smart hub for Niko Home Control
is OFF
| Switch on the power supply of the wireless smart hub for Niko Home Control
The battery of the Zigbee® switch is drained| A battery low warning is
displayed on the Niko Home Control Home app. A battery low indication (red-
coloured LED) will only be shown on the Zigbee® device after a long press on
the PROGRAM button (see § Reset). Replace the coin cell battery (refer to §
Battery replacement). Mind that the PRO- GRAM LED remains OFF when the battery
voltage level is below the minimum threshold
The receiver never responds when I press a Zigbee
® switch button in stand-alone use| The battery of the Zigbee®
switch is drained
The Zigbee® switch is not correctly paired with the receiver| Reset the
Zigbee® battery-pow- ered switch if it was paired to another Zigbee® network.
Pair the switch to a stand-alone receiver, Niko Home Control, or a third-
party Zigbee® network. See guide. niko.eu for more details
Another Zigbee® battery-powered switch is paired with the receiver
The Zigbee® battery-powered switch is mounted outside of the receiver’s radio
coverage or is sometimes moved outside
the range
| Move the Niko Zigbee® switch closer to the receiver or use a range extender
such as a 230 V powered Zigbee® 3.0 device in a Niko Home Control installation
or third-party system
The radio path is obstructed, which attenuates the radio signal| Reposition
the Zigbee® switch or use a range extender such as a 230 V powered Zigbee® 3.0
device in a Niko Home Control installation or third-party system
A jammer or a source of interfer- ence is blocking the telegrams from the
Zigbee® battery-powered switch to the receiver| Reposition the Zigbee® switch
or Zigbee® receiver. Remove the interfering device or use a range extender
such as a 230 V
powered Zigbee® 3.0 device in a Niko Home Control installation or third-party system
The Zigbee® battery-powered switch is defective| Replace the switch and pair
the new Zigbee® battery-powered switch with the receiver. Both devices may
have to be reset first
| The receiver is defective| Replace the receiver and pair it with the new
Zigbee® receiver
The receiver doesn’t always respond when I press the Niko
Zigbee ® battery-pow- ered switch| The receiver is located at
the border of the radio coverage area| Install the switch closer to the
receiver or use a range extender such as a 230 V powered Zigbee® 3.0 device in
a Niko Home Control installation or third-party system
A jammer or a source of interference is blocking the telegrams from the Niko
Zigbee® battery-powered switch to the receiver| Reposition the Zigbee® switch
or receiver, remove the interfering device or use a range extender such as a
230 V powered Zigbee® 3.0 device in a Niko Home Control installation or third-
party system
LED behaviour
The feedback LED will only be visible when the battery-powered Zigbee® switch is dismantled from the baseplate and after a long press on the PROGRAM button. The PROGRAM LED is found at the back of the switch.
PROGRAM LED is OFF| | The PROGRAM button is not pressed (correctly), or
the battery is empty| Press the PROGRAM button long enough or replace the coin
cell battery. The PROGRAM LED is not active during normal operation
---|---|---|---
PROGRAM LED is flashing blue|
| The switch is trying to connect to the Zigbee® network. The battery level is
sufficiently high| Wait until the LED stops flashing, which can take up to 90
seconds. The blinking frequency depends on the pairing method:
– repeated 1 x: EZ-mode pairing (Niko Home Control or third-party network)
– repeated 2 x: Touchlink pairing
– repeated 4 x: Find& Bind pairing
A flashing red LED also indicates a low battery level
PROGRAM LED is blue for 4 seconds| The wireless battery-
powered Zigbee® switch is connected to the Zigbee® network, and the battery
level is sufficiently high| The PROGRAM LED will switch OFF after 4 seconds.
The wireless battery-powered Zigbee® switch is ready to be used. A red LED
also indicates a low battery level
PROGRAM LED is flashing red| A red LED indicates that the battery
level is low. See above for more information on the difference between a
flashing LED and a LED that is permanently ON| Replace the coin cell battery.
The red LED is not active during normal operation and remains OFF when the
battery voltage level is too low
PROGRAM LED is permanently red
Reset
Specifications
Article number ………………………………………………………….552-721X2
Power supply ……………………………………………….. 3 V battery, CR2450
Battery life span ……………………………….. 5 years at 20 actuations/day
Protocol ……………………………………………………… Zigbee®3.0, 2.4 GHz
Mounting method 552-72002 ………………………………….wall mounting
Mounting method 552-72012 . flush-mounting box in combination with metal
baseplate 552-720X0
Flush-mounting box specifications ………………. depth = min. 40 mm
…………………………………………………………… claw/screw fixing = 60 mm
………………………………………………………….inner diameter box = 60 mm
…………………………….multiple boxes centre distance horizontal = 71 mm
………………………………. multiple boxes centre distance vertical = 71 mm
…………….multiple boxes centre distance vertical = 60 mm for BE and FR
Mounting height …………………………………………………… 105 – 120 cm
Dimensions with Niko Original or Niko Pure faceplate (HxWxD) …
………………………………………………………………………… 83 x 83 x 15 mm
Dimensions with Niko Intense faceplate (HxWxD) ……………………..
………………………………………………………………………… 85 x 85 x 15 mm
Protection degree ……………………………………………………………….IP20
Maximum range (between switch and smart hub or wireless
bridge) ……………………………………… 10 m (longer ranges possible with
……………………meshing capability of 230 V connected Zigbee® devices)
Maximum per installation … max. 50 connected Zigbee® devices per
……………………………………………………….. Niko Home Control installation
…………………………………………………………stand-alone: max. 8 Zigbee®
……………………………………………ON/OFF/dimmable actuators per switch
Operating frequency ……………………………………………………….2.4 GHz
Antenna …………………………………………………………. integrated antenna
Maximum RF power ………………………………………………….8 dBm EIRP
Ambient temperature operation ……………………………….5 °C – 30 °C
Ambient temperature storage ………………………………….0 °C – 40 °C
Humidity ……………………….. 0 – 95 % relative humidity, non-condensing
Weight 552-72002 ……………………………………………………… 23 g ±1 g
Weight 552-72012 ……………………………………………………… 17 g ±1 g
System compatibility ……………………………………….. talks with Homey
Marking ………………………………………………………………….. CE, Zigbee®
Warnings regarding installation
The installation of products that will permanently be part of the electrical installation and which include dangerous voltages, should be carried out by a qualified installer and in accordance with the applicable regulations. This user manual must be presented to the user. It should be included in the electrical installation file and it should be passed on to any new owners. Additional copies are available on the Niko website or via Niko customer services.
CE marking
This product complies with all of the relevant European guidelines and regulations. For radio equipment Niko llc declares that the radio equipment in this manual conforms with the 2014/53/EU directive. The full text of the EU declaration of conformity is available at www.niko.eu under the product reference, if applicable.
Environment
This product and/or the batteries provided cannot be disposed of in non-
recyclable waste. Take your discarded product to a recognised collection
point. Just like producers and importers, you too play an important role in
the promotion of sorting, recycling and reuse of discarded electrical and
electronic equipment. To finance the rubbish collection and waste treatment,
the government levies recycling charges in certain cases (included in the
price of this product).
Support & contact
nv Niko sa
Industriepark West 40
9100 Sint-Niklaas, Belgium
www.niko.eu
| +32 3 778 90 80 | support@niko.eu |
|---|
Niko prepares its manuals with the greatest care and strives to make them as
complete, correct and up-to-date as possible.
Nevertheless, some deficiencies may subsist. Niko cannot be held responsible
for this, other than within the legal limits. Please inform us of any
deficiencies in the manuals by contacting Niko customer services at
support@niko.eu.
PM552-720x2R23085
References
- Confluence Mobile - Niko Guide
- Niko - home automation, switches, socket outlets and detector
- Zigbee
- Niko - home automation, switches, socket outlets and detector
- Niko Home Control II programming software for Windows
- Niko Home Control II programming software for Mac
- Zigbee
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>