Autonics ASS-HC16MP0-NN SSR Terminal Block User Manual

: June 1, 2024
: Autonics

Table of Contents

Important Information
Features
Safety Considerations
Cautions during Use
Product Components
Sold Separately
Ordering Information
Specifications
Crimp Terminal Specifications
Replacing SSR
Dimensions
Installation
Temperature Characteristic Graph
Wire Connection
SSR AQZ202D [Panasonic]
CUSTOMER SUPPORT
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Autonics ASS-HC16MP0-NN SSR Terminal Block

Autonics ASS-HC16MP0-NN SSR Terminal Block

Important Information

For your safety, read and follow the considerations written in the instruction manual, other manuals and Autonics website.

The specifications, dimensions, etc. are subject to change without notice for product improvement. Some models may be discontinued without notice.

Features

Screw type connection for stable and reliable connection
Contactless relay ideal for systems requiring long life-cycle and high-speed response
Compact, space-saving design
Comprehensive connection type for use without jumper bar
Operation status indicator (blue LED)
DIN rail mount and screw mount installation
Convenient SSR removal with ejector clip
SSR protection cover

※ Autonics CH/CO series I/O terminal block cables are recommended for best performance.

Safety Considerations

Observe all ‘Safety Considerations’ for safe and proper operation to avoid hazards.
symbol indicates caution due to special circumstances in which hazards may occur.

Warning Failure to follow instructions may result in serious injury or death.

Fail-safe device must be installed when using the unit with machinery that may cause serious injury or substantial economic loss.(e.g. nuclear power control, medical equipment, ships, vehicles, railways, aircraft, combustion apparatus, safety equipment, crime/disaster prevention devices, etc.)
Failure to follow this instruction may result in personal injury, economic loss or fire.
Do not use the unit in the place where flammable/explosive/corrosive gas, high humidity, direct sunlight, radiant heat, vibration, impact or salinity may be present.
Failure to follow this instruction may result in explosion or fire.
Do not connect, repair, or inspect the unit, remove connector, or change SSR while connected to a power source.
Failure to follow this instruction may result in fire or electric shock.
Do not disassemble or modify the unit.
Failure to follow this instruction may result in fire or electric shock.

Caution Failure to follow instructions may result in injury or product damage.

Use the unit within the rated specifications.
Failure to follow this instruction may result in fire or product damage.
Use a dry cloth to clean the unit, and do not use water or organic solvent.
Failure to follow this instruction may result in fire or electric shock.
Keep the product away from metal chip, dust, and wire residue which flow into the unit.
Failure to follow this instruction may result in fire or product damage.
Do not use the product when a screw of terminal is loosened.
Failure to follow this instruction may result in fire or product damage.

Cautions during Use

Follow instructions in ‘Cautions during Use’. Otherwise, it may cause unexpected accidents.
Check the polarity of power or COMMON before connecting PLC or other controllers.
Do not touch the unit immediately after the load power is supplied or cut.
It may cause burn by high temperature.
24VDC power supply should be insulated and limited voltage/current or Class 2, SELV power supply device.
Wire as short as possible and keep away from high voltage lines or power lines, to prevent surge and inductive noise. Do not use near the equipment which generates strong magnetic force or high frequency noise (transceiver, etc.). In case installing the product near the equipment which generates strong surge (motor, welding machine, etc.), use diode or varistor to remove surge.
This unit may be used in the following environments.
- Indoors (in the environment condition rated in ‘Specifications’)
- Altitude max. 2,000 m
- Pollution degree 2
- Installation category II

Product Components

Product
Instruction manual
Ejector

Sold Separately

I/O cable CH/CO Series

Ordering Information

This is only for reference, the actual product does not support all combinations.
For selecting the specified model, follow the Autonics website.

Connector type
H : Hirose connector
Wire connection
C : Common
The number of SSR
16: 16-point
32: 32-point
SSR type
MP0 : AQZ202D [Panasonic]
Input logic
N : NPN (+COM)
P : PNP (-COM)
Varistor
N : None

Specifications

Model	ASS-HC16MP0-□N	ASS-HC32MP0-□N
Applied SSR 01)	AQZ202D [Panasonic]
Output method	1a	1a
Power supply	≤ 24 VDC ±10 %	≤ 24 VDC ±10 %
Current consumption	≤ 10.4 mA 02) or ≤ 13.1 mA 03)	≤ 11.5 mA 02) or ≤

15.3 mA 03)
SSR output rated spec.| 24 VAC∼50/60 Hz 1.6A, 24 VDC 1.6A

(1.6 A / 1-point, 8 A / 1COM)

| 24 VAC∼50/60 Hz 1.6A, 24 VDC 1.6A

(1.6 A / 1-point, 8 A / 1COM)

No. of connector pins| 20| 40
Connector for controller side| 20-pin Omron (XG4A-2031)| 40-pin Hirose

(HIF3BA-40PA-2.54DSA)

terminal pin: brass, Ni-plating

| CASE: MPPO, BASE: PA66 (G25%),

COVER: PC, terminal pin: brass, Ni-plating

Approval| Symbol | Symbol
Unit weight (packaged)| ≈ 185 g (≈ 232 g)| ≈ 370 g (≈ 463 g)

For the detailed information about the SSR, please refer to ‘SSR’ or data sheet from the manufacturer.
It is current consumption per a SSR including LED current.
It is current consumption including LED current for power part to 02).

Insulation resistance	≥ 1,000 MΩ (500 VDC megger)
Dielectric strength (coil-contact)	2,500 VAC∼50/60 Hz for 1 minute
Dielectric strength (same polarity contact)	1,000 VAC∼

50/60 Hz for 1 minute
Vibration| 0.75mm amplitude at frequency of 10 to 55Hz in each X, Y, Z direction for 2 hours
Vibration (malfunction)| 0.75mm amplitude at frequency of 10 to 55Hz in each X, Y, Z direction for 10 min
Shock| 300 m/s² (≈ 30 G) in each X, Y, Z direction for 3 times
Shock (malfunction)| 150 m/s² (≈ 15 G) in each X, Y, Z direction for 3 times
Ambient temperature| -15 to 55 ℃, storage: -25 to 65 ℃ (no freezing or condensation)
Ambient humidity| 35 to 85 %RH, storage: 35 to 85 %RH (no freezing or condensation)
Applicable wire – solid| Ø 0.3 to Ø 1.2 mm
---|---
Applicable wire – stranded| AWG 22-16 (0.30 to 1.25 mm²)
Tightening torque| 0.5 to 0.6 N·m

Crimp Terminal Specifications

Unit: mm, Use the UL approved crimp terminal.

Replacing SSR

Disassemble a SSR by using Two Way Ejector for SSR replacement inside the product.
After checking the location of the SSR socket, insert the SSR to be replaced.

Dimensions

Unit: mm, For the detailed drawings, follow the Autonics website.

Installation

DIN Rail

Mounting
1. Pull the Rail lock on the rear of the product to the direction ①.
2. Hang DIN rail hook on the rear of the product onto DIN rail.
3. Push the product to the direction ②, and push the Rail lock to the direction ③ to fix onto the DIN rail.
Removing
1. Insert a tool such as screwdriver into the hole of Rail lock.
2. Push the tool to the direction ① and pull the Rail lock.
3. Lift bottom of the product to the direction ② and remove the product from DIN rail.

Panel
Product with the mounting hole can be installed on panel with screw.
It is recommended to use M4×15 mm of spring washer screws.
If you use flat washer, its diameter should be Ø 6 mm.
Tighten the screw with the tightening torque of 0.7 to 1.0 N·m.

Example

When two or more terminal blocks are installed
: Use a stopper (sold separately) to make space between devices.

Temperature Characteristic Graph

Load current by ambient temperature for each rated current

VIN: 24 VDC
VIN is input voltage

Wire Connection

Wire connection

16-point NPN
16-point PNP
A| Pin| 20| 18| 16| 14| 12| 10| 8| 6| 19| 17| 15| 13| 11| 9| 7| 5
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---
COM| COM| COM1| COM2
B| Upper terminal| –| 01| –| 03| –| 05| –| 07| 08| –| 0A| –| 0C| –| 0E| –
–| R2| –| R4| –| R6| –| R8| R9| –| R11| –| R13| –| R15| –
C| Low terminal| 00| –| 02| –| 04| –| 06| –| –| 09| –| 0B| –| 0D| –| 0F
R1| –| R3| –| R5| –| R7| –| –| R10| –| R12| –| R14| –| R16
32-point NPN
32-point PNP
A| Pin| 40| 38| 36| 34| 32| 30| 28| 26| 24| 22| 20| 18| 16| 14| 12| 10
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---
COM| COM| COM1| COM2
B| Upper terminal| –| 01| –| 03| –| 05| –| 07| 08| –| 0A| –| 0C| –| 0E| –
–| R2| –| R4| –| R6| –| R8| R9| –| R11| –| R13| –| R15| –
C| Low terminal| 00| –| 02| –| 04| –| 06| –| –| 09| –| 0B| –| 0D| –| 0F
R1| –| R3| –| R5| –| R7| –| –| R10| –| R12| –| R14| –| R16
A| Pin| 39| 37| 35| 33| 31| 29| 27| 25| 23| 21| 19| 17| 15| 13| 11| 9
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---
COM| COM| COM3| COM4
B| Upper terminal| –| 11| –| 13| –| 15| –| 17| 18| –| 1A| –| 1C| –| 1E| –
–| R18| –| R20| –| R22| –| R24| R25| –| R27| –| R29| –| R31| –
C| Low terminal| 10| –| 12| –| 14| –| 16| –| –| 19| –| 1B| –| 1D| –| 1F
R17| –| R19| –| R21| –| R23| –| –| R26| –| R28| –| R30| –| R32

Hirose connector pin arrangement

20-pin connector
Omron (XG4A-2031)
40-pin connector
Hirose (HIF3BA-40PA-2.54DSA)

SSR AQZ202D [Panasonic]

Input

Rated voltage| Operate voltage| Release voltage| Input impedance
---|---|---|---
30 VDC | ≥ 4 V| ≤ 1.3 V| –

Output

Manufacture	Panasonic

Contact

arrangement

| SPST-1a (N.O)
Load voltage range| 60 VAC∼ / DC (Peak)
Max. load current| ≤ 2.7 A
Min. load current| –
Non-repetitive surge

current

| 9 A (Peak)
Output OFF leakage

current

| 10 μA
Output ON on voltage| –
Insulation resistance| ≥ 1,000 MΩ (500 VDC megger)
Dielectric strength (contact-coil)| 2,500 VAC∼ 50/60 Hz for 1 minute
Operate time| ≤ 10 ms
Release time| ≤ 3 ms
Ambient temperature| -40 to 60 ℃, storage: -40 to 100 ℃ (a non freezing or condensation environment)