behringer UL 1000G2-R UHF Wireless Belt Pack Receiver User Guide
- June 17, 2024
- Behringer
Table of Contents
behringer UL 1000G2-R UHF Wireless Belt Pack Receiver
Safety Instruction
-
. Please read and follow all instructions.
-
Keep the apparatus away from water, except for outdoor products..
-
Clean only with a dry cloth.
-
Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
-
Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including amplifiers) that produce heat.
-
Use only attachments/accessories specified by the manufacturer.
-
Use only specified carts, stands, tripods, brackets, or tables. Use caution to prevent tip-over when moving the cart/apparatus combination.
-
Avoid installing in confined spaces like bookcases.
-
Do not place naked flame sources, such as lighted candles
-
Operating temperature range 5° to 35°C (41° to 95°F)
-
Warning To prevent possible hearing damage, do not listen at high volume levels for long periods. As a guide to setting the volume level, check that you can still hear your own voice, when speaking normally while listening with the headphones.
-
Warning
- As with all small batteries, the batteries used with this product should be kept away from small children who still put things in their mouths. If they are swallowed, promptly call your local poison control center.
- Always purchase the correct size and grade of battery most suitable for intended use.
- Replace all batteries of a set at the same time.
- Clean the battery contacts, and also those of the device prior to battery installation.
- Ensure the batteries are installed correctly with the regard to polarity (+ and -).
- Always remove battery if consumed or if product is to be left unused for a long time.
- Replacement of a battery with an incorrect type can defeat a safeguard. Replace only with the same or equivalent type.
- Risk of fire or explosion if the battery is replaced by an incorrect type.
- Batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like.
- Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery can result in an explosion.
UL 1000G2-R Hook-up
Step 1: Hook-Up
UL 1000G2-R Controls
Step 2: Controls
- LEDS – indicate audio received, and receiver battery status
- LCD – displays the receiver details and menu
- ANTENNA – receive antenna
- PHONES – connect supplied earphones to this 3.5 mm stereo output
- VOLUME – adjust the earphones volume, and turn the receiver OFF
- BELT CLIP – attach receiver to belt
- MENU UP/DOWN – use to navigate the display menu
- SET – use to select receiver menu items. Open the battery compartment to access this button
- BATTERY COMPARTMENT – flip open to access the battery compartment (2x AA)
- EARPHONES – connect to receiver’s PHONES output. Make sure the volume is turned down before putting them on
Features
-
Package of one UL 1000G2-R wireless belt-pack receiver and
monitoring earphones, for the Behringer UL 1000G2 in-ear monitoring system -
Multiple UL 1000G2-R wireless belt-pack receivers can be used with the UL 1000G2 at the same time
-
UL 1000G2-R belt-pack receiver supports stereo / mono in-ear monitoring flexibility
-
Integrated display for channel frequency, squelch, and gain control
-
Working distance of up to 60 m (200 ft)
-
AA x 2 batteries included
This receiver is designed to work with the UL 1000G2 in-ear monitoring system only. For information regarding the installation and operation of the UL 1000G2-R, please read the quick start guide that comes with the UL-1000G2 transmitter/ receiver package.
UL 1000G2-R Getting started
Step 3: Getting started
RECEIVER SETUP
Main Menu
-
The main menu displays the AF level, mono/stereo mode, RF signal strength, EQ, LIM, MIX, lock, frequency, squelch, and battery level.
Selecting a Frequency Group -
Open the battery cover to access the SET button.
-
Press the SET button until GROUP flashes in the receiver display. Press up/down to select the same frequency group as the transmitter.
Selecting a Channel -
Press the SET button repeatedly until CHANNEL flashes in the receiver display. Press up/down to select the same channel as the transmitter.
Equalizer (EQ) -
The treble at 10 kHz is enhanced by 6 dB while the EQ is enabled.
-
Press the SET button repeatedly until “EQ” flashes in the receiver display. Use the up/down buttons to enable (EQ ON) or disable (EQ OFF) the Equalizer.
Limiter (LIM) -
To protect ears from injury, the Limiter function limits the level of audio signal to earphones at 400mV. It is advised to turn LIM ON if the receiver display indicates audio level is at maximum.
-
Press the SET button repeatedly until “LIM” flashes in the receiver display. Use the up/down buttons to enable (LIM ON) or disable (LIM OFF) the Limiter.
Mixer (MIX) -
Enable the Mixer function to listen to the mix of two mono signals, balance and regulate their volume.
For example: If the LEFT INPUT contains mono audio signal from instruments and the RIGHT INPUT contains mono audio signal vocals. The singer can monitor and adjust the volume balance between the instruments and his own voice and the overall volume level using the belt-pack receiver with MIX ON setting. -
Press the SET button repeatedly until “MIX” flashes in the receiver display. Use the up/down buttons to enable (MIX ON) or disable (MIX OFF) the Mixer.
Squelch (SQ) -
The Squelch function enables you to set a minimum threshold of signal received by the receiver. The setting consists of 3 bar levels – Low, Medium, and High. The receiver rejects signals below the set threshold and helps eradicate any unwanted audio signal transmitted by the transmitter.
-
Press the SET button repeatedly until “SQ” flashes in the receiver display. Use the up/down buttons to set Squelch at Low, Medium, or High.
Balance -
Adjust volume balance between left and right channels of a Stereo signal using the up/down buttons.
The audio is centered at -0- level. There are 9 levels available each for offset to the right channel and offset to the left channel. Positive values (1-, 2-, 3-, 4-, 5-, 6-, 7-, 8-, 9-) offset towards the Right, while negative values (-1-, -2-, -3-, -4-, -5-, -6-, -7-, -8-, -9-) offset towards the Left channel.
-
NOTE: To ensure the transmission of a stereo audio signal, the transmitter must be set in stereo mode and an audio signal must be present at the LEFT INPUT and the RIGHT INPUT.
Locking the Receiver against changes -
Press the SET button repeatedly until the LOCK icon flashes in the receiver display. Press up/down to select LOCK ON or LOCK OFF. LOCK ON function disables buttons, so no unwanted changes can be made accidentally.
-
NOTE: LOCK ON is enabled automatically if no operation is performed for 5 seconds. Under LOCK ON status, press and hold SET button for 2 seconds to disable LOCK momentarily and enables you to make changes.
Battery Power Status -
Remaining battery power status is displayed via four bars.
If no bars are visible on the battery symbol, the BATT LED will turn Red from Blue. The batteries should then be replaced immediately.
Specifications
Receiver
RF Frequency range| 584-608 MHz / 823-832 MHz / 863 – 865 MHz
Maximum channel number| For EU Frequency: 96 (depending upon the frequency
band)
For US Frequency: 120 (depending upon the frequency band)
Switching bandwidth| 24 MHz (depending upon the frequency band)
Sensitivity| <-92 dBm for 30 dB S/N ratio
Max PPM| +/- 15 kHz
Audio Frequency range| 70 Hz – 13.5 kHz (+/- 3 dB)
Signal to noise ratio| >80 dB(A)
THD| <1% to 1 kHz
Connectivity
Power switch| Volume on/of
Earphones output| 3.5 mm stereo
Power Requirements
Internal batteries| 2 x 1.5 VDC (AA)
Operating time| >6 hours/1300 mAH
Physical
Dimensions (W x H x D)| 64 x 98 x 22 mm (2.5 x 3.85 x 0.86″)
Weight| 100 g (without batteries)
Other important information
Important information
-
Register online.
Please register your new Music Tribe equipment right after you purchase it by visiting musictribe.com. Registering your purchase using our simple online form helps us to process your repair claims more quickly and efficiently. Also, read the terms and conditions of our warranty, if applicable. -
Malfunction. Should your
Music Tribe Authorized Reseller not be located in your vicinity, you may contact the Music Tribe Authorized Fulfiller for your country listed under “Support” at musictribe.com. Should your country not be listed, please check if your problem can be dealt with by our “Online Support” which may also be found under “Support” at music tribe.
com. Alternatively, please submit an online warranty claim at musictribe.com BEFORE returning the product.
FEDERAL COMMUNICATIONS COMMISSION COMPLIANCE INFORMATION
Behringer UL 1000G2-R
Responsible Party Name : Music Tribe Commercial NV Inc.
Addres s: 122 E. 42nd St.1, 8th Floor NY, NY 10168, United States
Email Address : legal@musictribe.com
UL 1000G2-R
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Important information:
Changes or modifications to the equipment not expressly approved by Music Tribe can void the user’s authority to use the equipment.
Hereby, Music Tribe declares that this product is in compliance with Directive
2014/53/EU, Directive 2014/30/EU, Directive 2014/35/EU, Directive 2011/65/EU
and Amendment 2015/863/ EU, Directive 2012/19/EU, Regulation 519/2012 REACH
SVHC and Directive 1907/2006/EC.
Full text of EU DoC is available at https ://community.musictribe.com/
EU Representative : Music Tribe Brands DK A/S
Address : Gammel Strand 44, DK-1202 København K, Denmark
UK Representative : Music Tribe Brands UK Ltd.
Address : 8th Floor, 20 Farringdon Street London EC4A 4AB, United Kingdom
Correct disposal of this product: This symbol indicates that this product must
not be disposed of with household waste, according to the WEEE Directive
(2012/19/EU) and your national law.
This product should be taken to a collection center licensed for the recycling
of waste electrical and electronic equipment (EEE). The mishandling of this
type of waste could have a possible negative impact on the environment and
human health due to potentially hazardous substances that are generally
associated with EEE. At the same time, your cooperation in the correct
disposal of this product will contribute to the efficient use of natural
resources. For more information about where you can take your waste equipment
for recycling, please contact your local city office, or your household waste
collection service.
Customer Support
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>