Adp Eye Semi Inset Basin Installation Guide

May 15, 2024
ADP

Adp Eye Semi Inset Basin

Adp-Eye-Semi-Inset-Basin-PRO

Product Information

Specifications

  • Product Type: Bathroom Basin
  • Styles Available: Above Counter, Semi-Inset, Inset, Under-Counter
  • Silicone Type: Non-acidic silicone recommended
  • Installation Time: Varies based on basin type and conditions

Product Usage Instructions

Above Counter Basins

  1. Apply 20mm silicon dots to hold basin in place.
  2. Limit to 3 fixing points for future removal.
  3. Seal with a bead of silicone around the edge after plumbing is finished.
  4. Wipe off excess silicone with a soft wet cloth.

Semi-Inset / Inset Basins

  1. Use non-acidic silicone for a continuous bead around the basin cut-out.
  2. Press basin firmly into place after positioning.
  3. Wipe off excess silicone with a soft wet cloth.

Under-Counter Basins

  1. Mark basin position on the benchtop underside.
  2. Apply silicone around the basin cut-out area.
  3. Place basin using the marked line as a guide.
  4. Let dry for 48hrs before flipping and installing on vanity cabinet.
  5. Wipe off excess silicone with a soft wet cloth.

Frequently Asked Questions (FAQ)

  • Q: Can I use any type of silicone for installation?
    A: It is recommended to use non-acidic silicone for installation to prevent damage to the basin or benchtop.

  • Q: How long should I let the silicone dry before using the basin?
    A: For best results, let the silicone dry for at least 48 hours before using the basin.

Above Counter Basins

Note: Basin replacement in the future is an important factor to consider when fixing and sealing basins.
By limiting silicon application as per instructions allows basin removal without damage to benchtops.

  • Apply 20mm silicon dots to hold basin in place, limit to 3 fixing points to enable future basin removal.Adp-Eye-Semi-Inset-Basin-1
  • DO NOT apply a bed of silicon to fix basin to benchtop as this will make it difficult in the future to replace basin.
  • Once basin is in final position and plumbing is finished, put a bead of silicon around the edge to seal and fix in place.Adp-Eye-Semi-Inset-Basin-2
  • Wipe down any excess silicone with a soft wet cloth.

Semi-Inset / Inset Basins

  • Using a non-acidic silicone, apply a continuous bead of silicon around the entire basin cut-out in the benchtop.Adp-Eye-Semi-Inset-Basin-3
  • Place semi-inset or inset basin into benchtop cut-out and press down firmly into positioning in place.Adp-Eye-Semi-Inset-Basin-4
  • Wipe down any excess silicone with a soft wet cloth.

Under-Counter Basins

Please note: if buying a benchtop and vanity from ADP, your ADP under- counter basin will come already installed.

  • Lay the benchtop down on a flat surface, with the underside facing up.

  • Place under-counter basin in position at the cut-out. With a marker, mark the outside of the basin so it easy to position in the next steps.
    Note: if using basin mixer, ensure there is enough room at the back or side of the basins for the basin mixer fixing to be tightened.

  • Using a non-acidic silicone, apply a continuous bead of silicon around the entire basin cut-out between the cut-out and the marked basin edge.

  • Place basin down in position on the silicon, using the marked line to guide you. When available use under-mount basin clips for best support (ADP do not supply).

  • Let dry face down for 48hrs (or longer in colder climates). Once dry, flip benchtop over and install on vanity cabinet.

  • Wipe down any excess silicone with a soft wet cloth.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals