Singfinity S330 Portable Karaoke Machine User Manual

PORTABLE KARAOKE MACHINE
S330
USER MANUAL

Speaker accessories

Show

1. Long press open / shut down : Short press light mode
2. Short press mode switch / double click open tws
3. The eq sound effects, and switch between indoor / outdoor
4. Short press the last song
5. Short press to play / pause
6. Press the next song
7. Short press / long press for volume reduction
8. Short/long press volume is added
9. Type-C The charging port can also do otg live connection
10. AUX IN Audio port
11. Live input
12. USB mouth
13. Headphone listening
14. Status indicator light

Operation Guidance

Key| Function|

Functional Operation

---|---|---

POWER

| Turn on| Short press POWER key for 1 second, if there is a U disk,Linec in speaker boot memory into the last working mode, do not insert U disk, Linec in boot speaker automatically enter the Bluetooth mode search state;Have prompt sound
shut down| On startup, press POWER for 2 seconds to turn off the Bluetooth speaker. There is a cue tone
Turn on/oft  RGB linht| On startup, press POWER key to switch RGB lighting mode
Forced Shutdown| In the crash state, long press the POWER key for 8 seconds to turn off the Bluetooth speaker

MODE

| Modec switching| Ashort press of the MODE key can switch to the BT /U disk /AUX mode.
Factory Data reset| In Bluetooth state, long press the MODE key for 8 seconds to restore the factory setting and clear the previous operation memory. There is a cue tone
BT disconnection| With Bluetooth connection, long press the MODE key for 2 seconds to disconnect the Bluetooth connection with a prompt tone
Tws| Double-click MODE (the speaker is in playback state and Bluetooth pairing state) and the speaker enters TWS state. (Double click MODE for the host), and then double click MODE to cancel TWS pairing.
1). Only speaker Ais in the Bluetooth pairing state, speaker B (connect the mobile phone and Bluetooth pairing state) double-click the MODE key to enter the TWS state, (double- click the MODE key for the host) the two speakers will automatically connect to the TWS connection
2). During the TWS group pair process, double-click the MODE key of one of the speakers to cancel the TWS group pair (timeout mode: the TWS group pair has succeeded over 30 seconds, and the host automatically returns to Bluetooth mode
3). Group pair success, double click any speaker MODE key, automatically exit TWS team mode
4) After TWS team, the machine can be switched on and off normally, and TWS can connect back
5). In TWS mode, only the host speaker can answer, hang up, reject and call, and the secondary machine has no call function

EQ

| Eq changing-over| Switch default EQ indoor, short press the EQ key for outdoor.
Save electricity| In the boot state, long press the EQ key for 5 seconds,the speaker is closed, and the power saving mode is turned on.
At this time, you can provide: 5V /1Acurrent to other electronic devices for a long time.
loudspeaker mute| Press the EQ key under USB /AUX/ BT for 2 seconds, and the speaker opens the external play mute function. At this time, the speaker is silent, and the listening interface is inserted into the headset.

Prev

| prev| Short press Prev key to switch to the previous song, long press quick back function (BT/U disk mode)

PLAY / PAUSE

| Piay / Pause| Press PLAY / PAUSE on Bluetooth / USB to pause the playback.
Call to answer| Press the PLAY / PAUSE button briefly during a phone call-in time. You can answer the phone call
Decline a call| Long press the PLAY / PAESE key for 2 seconds to reject the call .
Voice assistant| Connect the phone with Bluetooth, long press PALY / PAUSE for 2 seconds to start the voice assistant function. There is a cue tone

NEXT

| The next song| Press NEXT to switch to next song, long press fast forward (BT/U disk mode)

V-

| Volume reduction| Press the V-key short to reduce the volume. Long press the V-key, the volume is quickly reduced.

V+

| Volume plus| Short press the V button, increase the volume. Long press the V button to increase the volume quickly. Turn volume to maximum sound.

Type-c

| charge| 5V /2Asmart charging. Charge red light on, full red light out.

AUX

| AUX import| Insert the 3.5mm audio line to automatically play the music provided by AUX with a prompt sound.When playing, the blue light flashing, pause, the blue light long on.

LIVE

| 3.5 Live broadcast| Insert a 3.5mm headphone cable to automatically play the music of the speaker box.

USB

| USB mouth| Insert the U disk, automatically play the U disk music, with a prompt sound.When playing, the blue light flashing, pause, the blue light long on.
| Headphone listening| Insert a 3.5mm headphone cable to automatically play the music of the speaker box.

Status indicator light

1. Turn on, the Bluetooth indicator light is flashing.
2. Play/ pause the blue light after Blustooth connection
3. U disk, AUX play the blue light slow flash, pauss the biue light long light
4. EQ defaultindoor, green light is not on, green light for outdoor sound effect
5. When the TWS function is started, the yellow light flashes. After successful TWS pairing, the main and auxiliary yellow lights are on and the phone is connected The main yellow light, blue light long, auxiliary yellow light long, blue light out.
6. Charge, red light; full, red light out; low power reminder, red light flashing.

Other special states

1. If inserted U disk, Line in speaker boot, memory into the last working mode, do notinsert U disk,Line in On, the speaker will automatically enter the Bluetooth mode search state.
2. Bluetooth input: after starting on, first connect the last matched device, and ‘automatically enter the matching state after the connection fails The connection will be disconnected beyond the communication distance. If the connection is disconnected due to the extra distance, the connection will be initiated every 30 seconds within 10 minutes Secondary reconnection, disconnected beyond time.
3. Line in Input: insert the 3.5mm audio line into the audio input port and automatically enter the Line in mode And play the audio input from the Line in
4. Under Bluetooth | U disk / Line in, no audio input, silent
5. When the volume is the minimum, silent
6.  When the MODE key is clicked to enter the mode, the corresponding U disk or Line in line is not switched to the mode
7. In Bluetooth mode: when connecting to Blustooth, implement automatic shutdown after 10 minutes. (When connecting to the Bluetooth and the microphone Will not shut down; long press EQ speaker for 8 seconds, close, power saving mode)
8. Low-power alarm function. Low power alarm, red light flashing

Specification and parameters

BT version: 5.0
DSP sound processing: bass enhancement
Power rating: 100W
Maximumoutput: 120W
Power input: DC 5V/2A
Charging interval: ⩾ 8hours
The TWS connection distance: ⩾ 6m
Bluetooth distance: >10m(open area)
AUX mode: 3.5mm audio socket
Type-C: Type-C input/live streaming
Horn size: 78mm 4
Cell: 6000mAh
product size: 319147*142mm
Naked weight: 3.7KG
Charging method: Type-C 5V/2A
Impedance: 4R ± 15%

Use of the remote control device

Detailed function of remote control

1. Long press shutdown (can not boot) switch RGB light effect.
2. Clear the paired memory
3. Short/long press to increase volume (add to the louvoice)
4. Short press ona song, U disk mode, long press fast back function
5. Short press to play / pause
6. Short press the next song, U disk mode, long press the fast forward function
7. Short press / long press to lower the volume
8. Short press the indoor / outdoor sound effect switch
9. Short press to close the accompaniment, to restore the original singing
10. Short press to switch mode:BT/USB/AUX
11. Short press on/off TWS inter connection
12. Short press eliminates human voice, only accompaniment
13. Short press /long press reverberation effect is enhanced
14. Short press on / off microphone
15. Short press silent
16. Short press / long press reverberation effect is weakened
17. Short/ long press microphone increase
18. Short press, U disk current song began to play again
19. Short click, U disk single / list loop
20. Short / long press the microphone

Note: When the battery is low, the brightness is insufficient. Please replace the battery in time to avoid affecting the effective use of remote control and remote control. The remote control uses two no. 7 batteries. If not in use for a long time, please remove the battery to avoid leakage and damage to the remote control after the battery passes the shelf life

Microphone operation instructions

MIC Aand B:
Open AMIC A (CHA below the MIC display)
Open AMIC B (CHB below the MIC display)
Microphone frequency alignment method:
Turn on the speaker power and within 3 seconds, align the device with the microphone If the frequency alignment is not successful, first press and hold the power button to turn off the microphone
Unscrew the microphone tailpipe and have a SET button for frequency modulation and alignment
Press and hold the power button and SET button simultaneously, and a dashed line appears on the microphone display screen
When the dashed line disappears in the display screen, it indicates that the microphone has successfully aligned

Security Information

Security Information
Please read this manual carefully before using this machine. Pay attention to safe and correct operation, avoid unnecessary losses, and take preventive measures.
Warning: May cause malfunction or danger.
Safety warning

• If the machine emits smoke or other abnormal conditions occur, please quickly turn off the power and contact the local dealer for repair. Otherwise, it may cause fire and other hazards.
• Do not place containers containing liquids on the product, and do not allow liquids to enter the product as this may cause short circuits or other damage.
• Do not disassemble, repair or replace components without authorization.
• To prevent the dry battery from leaking liquid or heating and causing rupture, do not put the battery into fire, and pay attention to the type of battery used.
• Please use this machine in a well ventilated and dry place, and do not use itin damp places to avoid danger.
• The product remote control and wireless microphone contain batteries, which are easy for children to come into contact with and swallow. Ensure that the battery is always kept out of reach of children!
• Ensure that the product is placed horizontally and remains stable. Do not place it on a table or near debris that is prone to shaking.
• Do not place the product and accessories containing batteries in areas with high temperatures (such as direct sunlight or heating equipment).

Precautions
Attention: May affect machine functionality or cause damage.

• Do not use it for along time at high volume, as this listening environment will stimulate your ears and even seriously damage your hearing.
• Do not use pesticides, alcohol, paint thinners, or similar chemical solvents to clean this machine, as this may cause peeling or turbid corrosion on the surface of the casing. Please wipe with a clean dry cloth.
• If you do not use this device for a long time, please remove the remote control battery.

Important:
Keep the user manual for future reference.

FCC WARNING

This device complies with part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.Consult the dealer or an experienced radio/TV technician for help.

To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna.
FCC ID:2BCH6-S330

PRODUTC INSPECTION CERTIFCATE

Production test:…………………………….
Examination clerk:…………………………….
Quantity:…………………………….
Code:…………………………….
Date of manufacture:…………………………….
Operative norm:……………………………….

Warranty card (please warranty)
User files: month day___year

Username|
---|---
ContactAddress|
contact number|
Model|
Deater’s signature.|

Warranty terms

• Not specially marked, from the date of purchase, due to the purchased product quality problems (non-product software failure), the user can choose the return period is 7 days; the replacement period is 15 days; the warranty period is 12 months.
• When users encounter product quality problems, they can ask the designated service department of our company to provide three guarantees of services. If they need to be delivered, the user will bear the transportation and other related costs
• When the user requires three guarantees of service, he / she needs to voluntarily provide this valid warranty service certificate or invoice
• For additional services beyond the three guarantees of service, fees shall be charged in accordance with the relevant regulations. The warranty period of the products after charging maintenance is 3 months from the date of delivery or the date of delivery
• The services provided by our company are limited to products with quality problems; not including compensation for the loss of interest, loss caused by accident and any other indirect or direct loss
• Users should take the initiative to fill in some certificates at the seller according to the requirements. Our company will not bear the consequences of filling in the certificate according to the requirements, nor will we bear the commitment of the seller to provide the user beyond the warranty service regulations

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>