OXMART PA700 Electric Hoist Winch 1500lbs with Remote Control Instruction Manual
- June 1, 2024
- OXMART
Table of Contents
OXMART PA700 Electric Hoist Winch 1500lbs with Remote Control
Specifications
- Model: Electric Hoist Lift
- Rated Voltage (V): 110/220
- Input Power (W): 1300 (PA700), 1450 (PA800), 1800 (PA1000)
- Rate Lifting Weight (KG): 350/700 (PA700), 400/800 (PA800), 500/1000 (PA1000)
- Lifting Speed (M/Min): 10/5 (PA700), 10/5 (PA800), 10/5 (PA1000)
- Lifting Height (M): 12/6 (PA700), 12/6 (PA800), 12/6 (PA1000)
Installation
- First install the square hanger on the electric hoist crane with screws and washers.
- Fix the installed crane to the corresponding boom. Note that the dimensions must not exceed 4246.743.9 mm.
Method of Use
Plug in the power supply and control the crane through the wired remote control. Use the up and down buttons to raise or lower the load.
Precautions
-
1. The maximum support for a single hoist is 12 meters, and for a double hoist, it is 6 meters. - Ensure outlets comply with safety regulations and are grounded properly by a skilled electrician.
- Avoid letting children touch the machine when running unattended.
Features
-
1. High heat dissipation performance with a copper core motor for improved thermal conductivity and electrical conductivity. - Durable construction with galvanized high carbon steel wire and a strong impact-resistant metal case.
- Built-in safety brake mechanism for added safety, even in the event of a power cut.
FAQ
- Q: What should I do if the wire rope is worn?
- A: If the wire rope is worn, please replace it promptly to ensure safe operation.
PACKING INCLUDED
- A：1 * 1500lb Electric Hoist
- B：2 * Gloves
- C：1 * Lift Sling Strap
- D：1 * Hanging Hook
PARAMETERS
Specification
|
Method of Use
| Rated Volt
(V)
| Input Power
(W)
|
Rate Lifting Weight(KG)
| Lifting Speed
(M/Min)
| Lifting Height
(M)
---|---|---|---|---|---|---
PA700(700kg)
| Single-Hook|
110/220
|
1300
| 350| 10| 12
Double-Hook| 700| 5| 6
PA800(800kg)
| Single-Hook|
110/220
|
1450
| 400| 10| 12
Double-Hook| 800| 5| 6
PA1000(1000kg)
| Single-Hook|
110/220
|
1800
| 500| 10| 12
Double-Hook| 1000| 5| 6
INSTALLATION
- First, install the square hanger on the electric hoist crane with screws and washers.
- Fix the installed crane to the corresponding boom (NOTE: The width and height of the crossbar must not exceed the internal dimensions of the mounting bracket of 4246.743.9 mm.)
- Plug in the power supply, and control the crane through the wired remote control (use the up and down buttons to control whether to raise or lower).
PRECAUTIONS
-
The maximum support for a single hoist is 12 meters, and the maximum support for a double hoist is 6 meters
-
Outlets must comply with safety regulations. If your outlets don’t fit properly,they should be checked by a skilled electrician.
-
Your outlet plugs must be fully grounded, and your electrical system must be equipped with a magneto cutout safety device.
-
When the machine is running unattended, be careful not to let children touch it.
-
Do not pull the cable to disconnect the plug.
-
The machine should be protected from frost and low temperature.
-
When the machine cannot lift heavy objects, do not press the lifting button all the time, which means that the load exceeds the maximum capacity of the machine.
-
Do not disassemble the machine when it is running or powered on.
-
Do not stand under the heavy lifting objects.
-
Before starting work, make sure that the wire rope is properly wound on the drum with a pitch equal to the cable diameter.
-
Observe the maximum load displayed on the hoist. Don’t forget the hooks!
-
Leave at least three turns of the cable around the cable drum so there is no stress on the cable connection.
NOTE: To avoid any hazard, do not wrap more than 15 meters of cable on the drum. -
If the wire rope is worn, please replace the wire rope in time.
-
If the crane stops during the load lowering, it is normal for the load to drop a few centimetres due to inertia.
-
After working for 30 minutes, you can suspend the work to cool down the machine. Don’t continue to work for a long time, it is easy to wear the machine.
FEATURES
- High heat dissipation performance: copper core motor has good thermalconductivity and electrical conductivity, low voltage loss, high motor power and low heat generation. Built-in cooling fan improves airflow.
- Durable: The surface of high-carbon steel wire is galvanized, smooth and corrosion-resistant. The strands are tight and not easy to break. The metal case isbright red, strong and impact-resistant, easy to disassemble
- Safe and convenient: The built-in safety brake mechanism, it can hold the load even when the power is cut off. The stop device prevents topping, greatly improving safety. Dual channel mounting brackets are designed for easy flush mounting on beams. Remote control makes operation easier. The accessories required for installation are sent together with the electric hoist.
- Upgraded Version: Upgraded Manual Control Extension Cable 1.5 m (4.92 ft). An emergency stop switch helps you stop the lift if needed. Includes durable sling, work gloves, user manual, mounting accessories for easy installation and use.
- Two Channel Mounting Brackets: Easy to mount flush on beams.
- Hook: Alloy steel hook with stop device.
- Safety: Prevent topping and greatly improve safety.
- Wide range of uses: Lift regular or irregular shaped objects, such as stones, trees, lawn mowers, engines, truck roofs, etc.
- Where to Apply: Install vertically or horizontally in garages, ceilings, attics, barns, attics, anytime and anywhere you can imagine
PACKING LIST
(LIST OF ACCESSORIES OTHER THAN THE HOST)
- 1 * Durable Lift Sling Strap,
- 1 * Double Rope Hook,
- 1 * pair of Gloves,
- 1 * set of Installation accessories ( screws, washers and square hang brackets),
- 1 * User manual