BOSCH KEO Cordless Garden Saw Instruction Manual
- June 5, 2024
- Bosch
Table of Contents
Keo
Original instructions
Safety Notes
Explanation of symbols
| Read instruction manual.
---|---
****| General hazard safety alert.
| WARNING: Keep bystanders away.
| Remove battery before adjusting or cleaning, and before leaving the machine
unattended for any period.
| Do not expose to rain.
| Do not use a garden hose to clean the machine.
| Wear eye protection.
| Wear hand protection.
| Keep hands away from blade.
General Power Tool Safety Warnings
WARNING
Read all safety warnings, instructions, illustrations, and specifications
provided with this power tool. Failure to follow all instructions listed below
may result in electric shock, fire, and/ or serious injury. Save all warnings
and instructions for future reference. The term “power tool” in the warnings
refers to your mains-operated (corded) power tool or battery-operated
(cordless) power tool.
Work area safety
Keep the work area clean and well-lit. Cluttered or dark areas invite
accidents.
Do not operate power tools in explosive atmospheres, such as in the presence
of flammable liquids, gases or dust. Power tools create sparks that may ignite
dust
or fumes.
Keep children and bystanders away while operating a power tool. Distractions
can cause you to lose control.
Electrical safety
Power tool plugs must match the outlet. Never modify the plug in any
way. Do not use any adapter plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce the risk of electric shock.
Avoid body contact with earthed or grounded surfaces, such as pipes,
radiators, ranges, and refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
Do not expose power tools to rain or wet conditions. Water entering a
power tool will increase the risk of electric shock. u Do not abuse the cord.
Never use the cord for carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving parts. Damaged or entangled
cords increase the risk of electric shock.
When operating a power tool outdoors, use an extension cord suitable for
outdoor use. The use of a cord suitable for outdoor use reduces the risk of
electric shock.
If operating a power tool in a damp location is unavoidable, use a
residual current device (RCD) protected supply. The use of an RCD reduces the
risk of electric shock. Personal safety
Stay alert, watch what you are doing, and use common sense when
operating a power tool. Do not use a power tool while you are tired or under
the influence of drugs, alcohol or medication. A moment of inattention while
operating power tools may result in serious personal injury.
Use personal protective equipment. Always wear eye protection.
Protective equipment such as a dust mask, non-skid safety shoes, hard hat or
hearing protection used for appropriate conditions will reduce personal
injuries.
Prevent unintentional starting. Ensure the switch is in the off-position
before connecting to power source and/or battery pack, picking up or carrying
the tool. Carrying power tools with your finger on the switch or energising
power tools that have the switch on invites accidents.
Remove any adjusting key or wrench before turning the power tool on. A
wrench or a key left attached to a rotating part of the power tool may result
in personal injury.
Do not overreach. Keep proper footing and balance at all times. This
enables better control of the power tool in unexpected situations.
Dress properly. Do not wear loose clothing or jewellery. Keep your hair
and clothing away from moving parts. Loose clothes, jewelry or long hair can
be caught in moving parts.
If devices are provided for the connection of dust extraction and
collection facilities, ensure these are connected and properly used. Use of
dust collection can reduce dust-related hazards.
Do not let familiarity gained from frequent use of tools allow you to
become complacent and ignore tool safety principles. A careless action can
cause severe injury within a fraction of a second. Power tool use and care
Do not force the power tool. Use the correct power tool for your
application. The correct power tool will do the job better and safer at the
rate for which it was designed.
Do not use the power tool if the switch does not turn it on and off. Any
power tool that cannot be controlled with the switch is dangerous and must be
repaired.
Disconnect the plug from the power source and/or remove the battery pack,
if detachable, from the power tool before making any adjustments, changing
accessories, or storing power tools. Such preventive safety measures reduce
the risk of starting the power tool accidentally.
Store idle power tools out of the reach of children and do not allow
persons unfamiliar with the power tool or these instructions to operate the
power tool. Power tools are dangerous in the hands of untrained users.
Maintain power tools and accessories. Check for misalignment or binding
of moving parts, breakage of parts, and any other condition that may affect
the power tool’s operation. If damaged, have the power tool repaired before
use. Many accidents are caused by poorly maintained power tools.
Keep cutting tools sharp and clean. Properly maintained cutting tools
with sharp cutting edges are less likely to bind and are easier to control.
Use the power tool, accessories and tool bits etc. in accordance with
these instructions, taking into account the working conditions and the work to
be performed. Use of the power tool for operations different from those
intended could result in a hazardous situation.
**Keep handles and grasping surfaces dry, clean and free from oil and
grease. Slippery handles and grasping surfaces do not allow for safe handling
and control of the tool in unexpected situations.
Battery tool use and care
** Recharge only with the charger specified by the manufacturer. A charger
that is suitable for one type of battery pack may create a risk of fire when
used with another battery pack.
Use power tools only with specifically designated battery packs. Use of
any other battery packs may create a risk of injury and fire.
When the battery pack is not in use, keep it away from other metal
objects, like paper clips, coins, keys, nails, screws or other small metal
objects, that can make a connection from one terminal to another. Shorting the
battery terminals together may cause burns or a fire.
Under abusive conditions, liquid may be ejected from the battery; avoid
contact. If contact accidentally occurs, flush with water. If liquid contacts
eyes, additionally seek medical help. Liquid ejected from the battery may
cause irritation or burns.
Do not use a battery pack or tool that is damaged or modified. Damaged
or modified batteries may exhibit unpredictable behavior resulting in fire,
explosion or risk of injury.
Do not expose a battery pack or tool to fire or excessive temperature.
Exposure to fire or temperature above 130°C may cause an explosion.
Follow all charging instructions and do not charge the battery pack or
tool outside the temperature range specified in the instructions. Charging
improperly or at temperatures outside the specified range may damage the
battery and increase the risk of fire.
Service
Have your power tool serviced by a qualified repair person using only
identical replacement parts. This will ensure that the safety of the power
tool is maintained.
Never service damaged battery packs. Service of battery packs should
only be performed by the manufacturer or authorized service providers.
Safety instructions for reciprocating saws
Hold the power tool by insulated gripping surfaces, when performing an
operation where the cutting accessory may contact hidden wiring. Cutting
accessory contacting a “live” wire may make exposed metal parts of the power
tool “live” and could give the operator an electric shock.
Use clamps or another practical way to secure and support the workpiece
to a stable platform. Holding the workpiece by hand or against your body
leaves it unstable and may lead to loss of control.
Do not use the power tool with the hook without rubber covers or with
damaged rubber covers. If the rubber covers on the hook are damaged, replace
the hook by a new one.
Keep hands away from the sawing area. Do not reach under the workpiece.
Contact with the saw blade can lead to injuries.
Only bring the power tool into contact with the workpiece when switched
on. Otherwise, there is a danger of kickback if the cutting tool jams in the
workpiece.
Ensure that the footplate is always resting on the workpiece while
sawing. The saw blade can jam and lead to loss of control over the power tool.
When the cut is completed, switch off the power tool and then pull the
saw blade out of the cut only after it has come to a standstill. In this
manner, you can avoid kickback and can place down the power tool securely.
Always wait until the power tool has come to a complete stop before
placing it down. The application tool can jam and cause you to lose control of
the power tool.
Use only undamaged saw blades that are in perfect condition. Bent or
dull saw blades can break, negatively influence the cut, or lead to kickback.
Do not brake the saw blade to a stop by applying side pressure after
switching off. The saw blade can be damaged, break or cause kickback.
Ensure that the material is securely clamped. Do not support the
workpiece using your hands or feet. Do not touch any objects or the floor with
the saw while it is running. There is a risk of kickback.
Use suitable detectors to determine if there are hidden supply lines or
contact the local utility company for assistance. Contact with electric cables
can cause fire and electric shock. Damaging gas lines can lead to explosions.
Breaking water pipes causes property damage.
Before any work on the machine (e. g. maintenance, changing the tool,
etc.) as well as during its transport and storage, always remove the battery
and lock the On/Off switch in the off position. The danger of injury when
accidentally actuating the On/Off switch.
Wear gloves, saw blades are sharp and can become hot during cutting.
Use a dust mask when cutting wood that has been treated with a chemical
wood preservative.
Do not modify any components on the machine.
The danger of injury.
****Use only original Bosch accessories.
Safety Instructions and Recommendations for Optimal Handling of the
Battery
Ensure the product is switched off before inserting the battery.
Inserting the battery into a product that has the switch on can cause
accidents.
Use only Bosch batteries intended specifically for this product. The use
of any other batteries may create a risk of injury and fire.
****Do not open the battery. There is a risk of short-circuiting.
Protect the battery against heat (e.g., against continuous intense sunlight), fire, water, and moisture. There is a risk of explosion.
Keep the battery not used away from paper clips, coins, keys, nails,
screws, or other small metal objects, that can make a connection from one
terminal to another. Shorting the battery terminals together may cause burns
or a fire.
In case of damage and improper use of the battery pack, vapors may be
emitted. Ventilate the area and seek medical help in case of complaints. The
vapors can irritate the respiratory system.
Only use the battery with products from the manufacturer. This is the
only way in which you can protect the battery against dangerous overload.
The battery can be damaged by pointed objects such as nails or
screwdrivers or by force applied externally. An internal short circuit may
occur, causing the battery to burn, smoke, explode or overheat.
Do not short-circuit the battery. There is a risk of explosion.
Protect the battery against moisture and water.
Store the product and battery only within a temperature range between –20
°C and 50 °C. As an example, do not leave the battery in the car in summer.
Occasionally clean the venting slots of the battery using a soft, clean,
and dry brush.
Symbols
The following symbols are important for reading and understanding the original
instructions. Please take note of the symbols and their meaning. The correct
interpretation of the symbols will help you to use the product in a better and
safer manner.
Symbol | Meaning |
---|---|
Only use the battery charger indoors in dry conditions. | |
Movement direction | |
Reaction direction | |
Switching on | |
Switching off | |
Permitted action | |
Prohibited action | |
Accessories/Spare parts |
Product description and specifications
Read all safety warnings and all instructions. Failure to follow the safety warnings and instructions may result in electric shock, fire, and/or serious injury. Please observe the illustrations at the ending of this operatingmanual.
Intended use
This power tool is intended for garden and household use. It is for cutting
branches and can also be used for the sawing of wood, soft metal (such as
copper), and plasterboard.
It is suitable for straight and curved cuts. The saw blade recommendations
must be observed.
Product Features (see figure A)
- Removable hook
- Saw blade holder
- Lock for saw blade
- Lock for hook
- Battery charge-control indicator
- On/Off switch
- Lock-off button for On/Off switch
- Saw blade
- Battery
- Charger a)
- Handle (insulated gripping surface)
- Battery unlocking button
a) Accessories shown or described are not included with the product as standard. You can find the complete selection of accessories in our accessories range.
Technical Data
Sabre saw | Keo | |
---|---|---|
Article number | 3 600 H61 A.. | |
Rated voltage | V | 18 |
Stroke rate at no load no | min¹ | 0 – 2300 |
Tool holder | SDS | |
Stroke | mm | 20 |
– in wood | mm | 80 |
– in soft metal | mm | 7 |
Weight according to EPTA-Procedure 01:20148) | kg | 1.4 |
Recommended ambient temperature during charging | °C | 0… +35 |
Permitted ambient temperature during operation A) and storage | °C | -20… +50 |
Battery type _ | PBA 18V…W-. 1.5 Ah, 2.0 Ah, 2.5 Ah, 3.0 Ah, 4.0 Ah, 5.0 Ah, |
6.0 Ah
A) Limited performance at temperatures < 0 °C
B) Depends on battery in use
The specifications apply to a rated voltage [U] of 230 V. These specifications
may vary at different voltages and in country-specific models.
Noise/Vibration Information
Noise emission values were determined according to EN 62841-2-11.
Typically the A-weighted sound pressure level of the product is 74 dB(A).
Uncertainty K = 5 dB. The noise level when working can exceed the declared
values.
Wear hearing protection!
Vibration total values ah (triax vector sum) and uncertainty K determined
according to EN 62841-2-11: Sawing chipboard with saw blade S 644 D: ah,B = 19
m/s2, = 1.5 m/s2
,Sawing wood beams with saw blade S 644 D: ah,WB = 20 m/s2, K = 1.5 m/s2.
That the declared vibration total value(s) and the declared noise emission value(s) have been measured in accordance with a standard test method and may be used for comparing one tool to another. That the declared vibration total value(s) and the declared noise emission value(s) may also be used in a preliminary assessment of exposure. That the vibration and noise emissions during actual use of the power tool can differ from the declared values depending on the ways in which the tool is used especially what kind of workpiece is processed; and the need to identify safety measures to protect the operator that is based on an estimation of the exposure measures in the actual conditions of use (taking account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle in addition to the trigger time).
Mounting and Operation
Action | Figure | Page |
---|---|---|
Delivery scope | A | 203 |
Mounting the Hook | B | 204 |
Checking if the Hook fits correctly | C | 205 |
Inserting/Replacing the Saw Blade | D | 205 |
Checking if the Blade is connected | E | 206 |
Inserting/removing the battery | F | 206 |
Switching on and off/Controlling the Stroke Rate | G – H | 207 |
Working Advice | I – J | 208 – 209 |
Maintenance and cleaning | K | 209 |
Selecting accessories | L | 210 |
Starting Operation
****Remove the battery from the power tool before carrying out work on the power tool (e.g. maintenance, changing tool, etc.). The battery should also be removed for transport and storage. There is a risk of injury from unintentionally pressing the on/off switch.
Inserting/removing the battery (see figure F)
Note: Using unsuitable batteries can lead to malfunctions of or cause
damage to the power tool. Insert the charged battery (9). Make sure that the
battery is fully fitted. To remove the battery (9) from the machine, press the
battery unlocking button (12) and pull the battery out.
Battery charge indicator
The battery charge indicator (5) indicates the remaining battery capacity or
an overload when the power tool is switched on.
LED | Capacity |
---|---|
Continuous lighting 3 x green | ≥ 75 % |
Continuous lighting 2 x green | 40 − 75 % |
Continuous lighting 1 x green | 15 − 40 % |
Slow flashing 1 x green | 0 − 15 % |
Operation
Switching on and off (see figure G)
Firstly, press the lock-off button (7) and then the On/Off switch(6). You can
release the lock-off button (7) when the power tool is running. The lock-off
button (7) engages again as soon as the power tool comes to a complete stop.
Working Advice
****Always follow the safety advice provided.
Selecting the saw blade
Use only saw blades suitable for the material being worked. An overview of
recommended saw blades can be found at the end of these operating
instructions. Do not use other
blades than recommended. Use a narrow saw blade when sawing tight curves.
Dust/Chip Extraction
Dust from materials such as lead-containing coatings, some wood types,
minerals, and metal can be harmful to one’s health. Touching or breathing in
the dust can cause allergic
reactions and/or lead to respiratory infections of the user or bystanders.
Certain dust, such as oak or beech dust, is considered carcinogenic,
especially in connection with wood-treatment additives (chromate, wood
preservative). Materials containing asbestos may only be worked by
specialists.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the materials to be
worked.
****Avoid dust accumulation at the workplace. Dust can easily ignite.
Troubleshooting
Sabre saw
Problem
Power tool fails to op- erate| Possible Cause Battery discharged| Corrective
Measure
Recharge battery; also see “Battery Charging”
---|---|---
Power tool defective| Contact Service Agent.
Internal wiring of garden tool defective| Contact Service Agent.
Power tool functions intermittently| On/Off switch defective| Contact Service
Agent.
Excessive vibrations/ noise| Power tool defective| Contact Service Agent.
Sawing time per battery charge too low| The blade holder area needs cleaning|
Hold the tool to point to the ground and start to operate
Saw blade worn| Change saw blade
Poor sawing technique| see “Working Advice”
Battery is not fully charged| Recharge battery; also see “Battery Charging”
The saw blade is run- ning slow| The battery is getting discharged| Recharge
battery; also see “Battery Charging”
Overloaded during operation| Reduce pressing force of tool against branch
Maintenance and Service
Maintenance, Cleaning, and Storage
Always follow the safety advice provided.
Clean the power tool and the saw blade mount regularly if material accumulates and can hinder movement. Clean the saw blade mount preferably with compressed air or with a soft brush. For this, remove the saw blade from the power tool. Ensure proper operation of the saw blade holder by applying a suitable lubricant. Heavy contamination of the machine can lead to malfunctions. Therefore, do not saw materials that produce a lot of dust from below or overhead. Store the power tool in a secure, dry place, out of the reach of children. Do not place other objects on the power tool.
Battery Maintenance
Use the following procedures to enable optimum usage of the battery:
– Protect the battery against moisture and water.
– Store the machine and battery only within a temperature range between –20 °C
and 50 °C . As an example, do not leave the battery in the car in summer.
– It is recommended that the battery is not stored within the product but
stored separately.
– Do not leave the battery in the product in direct sunlight.
– The ideal storage condition for the battery is 5 °C.
– Occasionally clean the venting slots of the battery using a soft, clean and
dry brush.
A significantly reduced working period after charging indicates that the
battery is used and must be replaced.
After-Sales Service and Application Service Our after-sales service responds to your questions concerning the maintenance and repair of your product as well as spare parts. You can find explosion drawings and information on spare parts at: www.bosch-pt.com The Bosch product use advice team will be happy to help you with any questions about our products and their accessories. In all correspondence and spare parts orders, please always include the 10‑digit article number given on the nameplate of the product.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange the collection of a
product in need of servicing or repair.
Tel. Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com
You can find further service addresses at: www.bosch- pt.com/serviceaddresses
Transport The recommended lithium-ion batteries are subject to legislation on the transport of dangerous goods. The user can transport the batteries by road without further requirements. When shipping by third parties (e.g.: by air transport or forwarding agency), special requirements on packaging and labeling must be observed. For the preparation of the item being shipped, consulting an expert for hazardous material is required. Dispatch battery packs only when the housing is undamaged. Tape or mask off open contacts and pack up the battery in such a manner that it cannot move around in the packaging. Please also observe the possibility of more detailed national regulations.
Disposal
The product, batteries, accessories, and packaging should be sorted for
environmental-friendly recycling.
**** Do not dispose of the product and batteries/rechargeable batteries into
household waste!
Only for EU countries:
According to the European Guideline 2012/19/EU, products that are no longer
usable, and according to the European Guideline 2006/66/EC, defective or used
battery acks/
batteries must be collected separately and disposed of in an environmentally
correct manner.
Only for the United Kingdom
According to Waste Electrical and Electronic Equipment Regulations, 2013
(2013/3113) and the Waste Batteries and Accumulators Regulations 2009
(2009/890), power tools that are no longer usable must be collected separately
and disposed of in an environmentally friendly manner.
Battery packs/batteries:
Li-ion:
Please observe the notes in the section on transport (see “Transport”, page
15).
GB Importer:
Robert Bosch Ltd.
Broadwater Park
North Orbital Road
Uxbridge UB9 5HJ
|
---|---
|
|
|
Licenses
Apache License
Copyright © 2009-2019 Arm Limited. All rights reserved.
Copyright © 2018-2019 STMicroelectronics. All rights reserved.
Version 2.0, January 2004 http://www.apache.org/licenses/ TERMS AND
CONDITIONS FOR USE, REPRODUCTION, AND DISTRIBUTION
- Definitions. “License” shall mean the terms and conditions for use, reproduction, and distribution as defined by Sections 1 through 9 of this document. “Licensor” shall mean the copyright owner or entity authorized by the copyright owner that is granting the License. “Legal Entity” shall mean the union of the acting entity and all other entities that control, are controlled by, or are under common control with that entity. For the purposes of this definition, “control” means (i) the power, direct or indirect, to cause the direction or management of such entity, whether by contract or otherwise, or (ii) ownership of fifty percent (50%) or more of the outstanding shares, or (iii) beneficial ownership of such entity. “You” (or “Your”) shall mean an individual or Legal Entity exercising permissions granted by this License. “Source” form shall mean the preferred form for making modifications, including but not limited to software source code, documentation source, and configuration files. “Object” form shall mean any form resulting from mechanical transformation or translation of a Source form, including but not limited to compiled object code, generated documentation, and conversions to other media types. “Work” shall mean the work of authorship, whether in Source or Object form, made available under the License, as indicated by a copyright notice that is included in or attached to the work (an example is provided in the Appendix below). “Derivative Works” shall mean any work, whether in Source or Object form, that is based on (or derived from) the Work and for which the editorial revisions, annotations, elaborations, or other modifications represent, as a whole, an original work of authorship. For the purposes of this License, Derivative Works shall not include works that remain separable from, or merely link (or bind by name) to the interfaces of, the Work and Derivative Works thereof. “Contribution” shall mean any work of authorship, including the original version of the Work and any modifications or additions to that Work or Derivative Works thereof, that is intentionally submitted to Licensor for inclusion in the Work by the copyright owner or by an individual or Legal Entity authorized to submit on behalf of the copyright owner. For the purposes of this definition, “submitted” means any form of electronic, verbal, or written communication sent to the Licensor or its representatives, including but not limited to communication on electronic mailing lists, source code control systems, and issue tracking systems that are managed by, or on behalf of, the Licensor for the purpose of discussing and improving the Work, but excluding communication that is conspicuously marked or otherwise designated in writing by the copyright owner as “Not a Contribution.” “Contributor” shall mean Licensor and any individual or Legal Entity on behalf of whom a Contribution has been received by Licensor and subsequently incorporated within the Work.
- Grant of Copyright License. Subject to the terms and conditions of this License, each Contributor hereby grants to You a perpetual, worldwide, non-exclusive, no-charge, royalty-free, irrevocable copyright license to reproduce, prepare Derivative Works of, publicly display, publicly perform, sublicense, and distribute the Work and such Derivative Works in Source or Object form.
- Grant of Patent License. Subject to the terms and conditions of this License, each Contributor hereby grants to You a perpetual, worldwide, non-exclusive, no-charge, royalty-free, irrevocable (except as stated in this section) patent license to make, have made, use, offer to sell, sell, import, and otherwise transfer the Work, where such license applies only to those patent claims licensable by such Contributor that is necessarily infringed by their Contribution(s) alone or by a combination of their Contribution(s) with the Work to which such Contribution(s) was submitted. If You institute patent litigation against any entity (including a cross-claim or counterclaim in a lawsuit) alleging that the Work or a Contribution incorporated within the Work constitutes a direct or contributory patent infringement, then any patent licenses granted to You under this License for that Work shall terminate as of the date such litigation is filed.
- Redistribution.You may reproduce and distribute copies of the Work or Derivative Works thereof in any medium, with or without modifications, and in Source or Object form, provided that You meet the following conditions: – You must give any other recipients of the Work or Derivative Works a copy of this License; and – You must cause any modified files to carry prominent notices stating that You changed the files; and – You must retain, in the Source form of any Derivative Works that You distribute, all copyright, patent, trademark, and attribution notices from the Source form of the Work, excluding those notices that do not pertain to any part of the Derivative Works; and – If the Work includes a “NOTICE” text file as part of its distribution, then any Derivative Works that You distribute must include a readable copy of the attribution notices contained within such NOTICE file, excluding those notices that do not pertain to any part of the Derivative Works, in at least one of the following places: within a NOTICE text file distributed as part of the Derivative Works; within the Source form or documentation, if provided along with the Derivative Works; or, within a display generated by the Derivative Works, if and wherever such third-party notices normally appear. The contents of the NOTICE file are for informational purposes only and do not modify the License. You may add Your own attribution notices within Derivative Works that You distribute, alongside or as an addendum to the NOTICE text from the Work, provided that such additional attribution notices cannot be construed as modifying the License. You may add Your own copyright statement to Your modifications and may provide additional or different license terms and conditions for use, reproduction, or distribution of Your modifications, or for any such Derivative Works as a whole, provided Your use, reproduction, and distribution of the Work otherwise complies with the conditions stated in this License.
- Submission of Contributions. Unless You explicitly state otherwise, any Contribution intentionally submitted for inclusion in the Work by You to the Licensor shall be under the terms and conditions of this License, without any additional terms or conditions. Notwithstanding the above, nothing herein shall supersede or modify the terms of any separate license agreement you may have executed with the Licensor regarding such Contributions.
- Trademarks. This License does not grant permission to use the trade names, trademarks, service marks, or product names of the Licensor, except as required for reasonable and customary use in describing the origin of the Work and reproducing the content of the NOTICE file.
- Disclaimer of Warranty. Unless required by applicable law or agreed to in writing, Licensor provides the Work (and each Contributor provides its Contributions) on an “AS IS” BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied, including, without limitation, any warranties or conditions of TITLE, NON-INFRINGEMENT, MERCHANTABILITY, or FITNESS FOR A PARTICULAR PURPOSE. You are solely responsible for determining the appropriateness of using or redistributing the Work and assume any risks associated with Your exercise of permissions under this License.
- Limitation of Liability. In no event and under no legal theory, whether in tort (including negligence), contract, or otherwise, unless required by applicable law (such as deliberate and grossly negligent acts) or agreed to in writing, shall any Contributor be liable to You for damages, including any direct, indirect, special, incidental, or consequential damages of any character arising as a result of this License or out of the use or inability to use the Work (including but not limited to damages for loss of goodwill, work stoppage, computer failure or malfunction, or any and all other commercial damages or losses), even if such Contributor has been advised of the possibility of such damages.
- Accepting Warranty or Additional Liability. While redistributing the Work or Derivative Works thereof, You may choose to offer, and charge a fee for, acceptance of support, warranty, indemnity, or other liability obligations and/or rights consistent with this License. However, in accepting such obligations, You may act only on Your own behalf and on Your sole responsibility, not on behalf of any other Contributor, and only if You agree to indemnify, defend, and hold each Contributor harmless for any liability incurred by, or claims asserted against, such Contributor by reason of your accepting any such warranty or additional liability. END OF TERMS AND CONDITIONS
Copyright © 2020 STMicroelectronics
All rights reserved.
Redistribution and use in source and binary forms, with or without
modification, are permitted provided that the following conditions are met:
– Redistributions of source code must retain the above copyright notice, this
list of conditions, and the following disclaimer.
– Redistributions in binary form must reproduce the above copyright notice,
this list of conditions, and the following disclaimer in the documentation
and/or other materials provided with the distribution.
– Neither the name of STMicroelectronics nor the names of its contributors may
be used to endorse or promote products derived from this software without
specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
Robert Bosch Power Tools GmbH
70538 Stuttgart
GERMANY
www.bosch-pt.com
References
- Invented for life | Bosch Global
- The domain name bosch.mk is for sale
- Početna strana | Bosch u Srbiji
- Skånevik Ølen Kraftlag AS
- Licenses
- ЕлектроінÑтрументи Bosch | Bosch Professional
- ÐлектроинÑтрументы Bosch | Bosch Professional
- Bosch Power Tools | Bosch Power Tools
- Location selection | Bosch Power Tools
- Електроинструменти на Bosch | Електроинструменти на Bosch
- Service worldwide
- Elektrické nářadí Bosch | Elektrické nářadí Bosch
- Bosch Elektrowerkzeuge und Zubehör | Bosch Elektrowerkzeuge
- Bosch el-værktøj | Bosch el-værktøj
- Bosch-sähkötyökalut | Bosch-sähkötyökalut
- Outillage électroportatif Bosch | Outillage électroportatif Bosch
- Ηλεκτρικά εργαλεία Bosch | Ηλεκτρικά εργαλεία Bosch
- Bosch elektromos kéziszerszámok | Bosch elektromos kéziszerszámok
- Elektronarzędzia Bosch | Elektronarzędzia Bosch
- Scule electrice Bosch | Scule electrice Bosch
- Bosch električni alati | Bosch električni alati
- Bosch Услуги | Электроинструменты Bosch
- Elektrické náradie Bosch | Elektrické náradie Bosch
- Invented for life | Bosch Global
- Ana Sayfa | Bosch Türkiye
- Početna | Bosch u Hrvatskoj
- herramientasbosch.net