POWERWAND Cordless Cellular Shades Motorization User Guide

POWERWAND Cordless Cellular Shades Motorization

Product Information

Specifications

• Product Name: POWERWANDTM
• Compatible Shades: Honeycomb Shades, Dual Shades, Roller Shades, Sheer Shadings, Natural Woven Shades
• Features: Wand control, Favorite Position setting, Advanced Programming options

Product Usage Instructions:

Installation and Wand Attachment
Before programming, install the shade according to the provided instructions. For Honeycomb Shades, connect the battery cable into the slot inside the headrail before hanging the shades on the brackets.

Sheer Shadings, Dual & Roller Shades
Attach the wand by placing the top on the metal hook support and connecting the cable into the motor head.

Honeycomb Shades
Attach the pre-connected wand to the plastic hook support on the motor control side.

Natural Woven Shades
Approach the hook with the wand parallel to the headrail, twist gently to attach it, and connect the cable into the motor.

Operating the Wand
Use the wand buttons to control the shade movement. The LED indicates operation status.

Setting a Favorite Position:

1. Press and release the PROG button.
2. Move the shade to the desired position.
3. Press and release the PROG button again.

Removing a Favorite Position

1. Press and hold the PROG button for 7 seconds.
2. Move the shade to the favorite position.

Advanced Programming
Switch modes, adjust limits, or reset the motor following specific steps to avoid damage to the shade.

Charging the Battery
Ensure to charge the battery when needed using the Micro USB charging port located on the wand.

Frequently Asked Questions (FAQ)

• Q: Can I switch between Roller and Window Shadings Mode easily?
  A: Yes, you can switch between modes by following the provided instructions for Advanced Programming.

• Q: How do I reset the Factory Motor?
  A: To reset the Factory Motor, press and hold the STOP button for 5 seconds, then press and hold the PROG button for 7 seconds.

POWERWAND™
Honeycomb Shades | Dual Shades | Roller Shades
Sheer Shadings | Natural Woven Shades

QUICK PROGRAMMING GUIDE

Important: Before starting the programing, install the shade following the installation instructions provided.
For Honeycomb Shades, connect the battery cable into the slot located in the endcap, inside the headrail, before hanging the shades on the brackets.

• 1a. Attach the Wand — Sheer Shadings, Dual & Roller Shades
• 1b. Attach the Wand — Honeycomb Shades
• On Dual Shades, Roller Shades and Sheer Shadings, with the wand control buttons facing you, attached the top of the wand on the metal hook support (1) on the motor control side, then connect the cable into the motor head (2).
• On Honeycomb shades, the wand will be already connected to the shade (1). With the wand control buttons facing you, attached the top of the wand into the plastic hook support on the motor control side (2).
• On Natural Woven Shades, with the wand control buttons facing you (1) approach the hook with the wand parallel to the headrail. (2) Gently twist the wand to attach it to the hook. Connect the cable into the motor.

Operate the Wand

Roller and Honeycomb Mode:

• Press the DOWN or UP button to lower or raise the shade. Press the STOP to stop the shade at the desired position.

Window Shadings and Dual Shades Mode:

• Tapping the UP or DOWN button for less than 2 seconds will move the shade in short steps.
• Holding the UP or DOWN button down for more than 2 seconds before releasing will operate the shade at the standard speed.
• Press the STOP button to stop the shade at the desired position.

Set a Favorite Position

IMPORTANT: Once the favorite position is set, the shade will always stop at the designed favorite position when passing by it. Click 2 x Up or Down button, the shade will go to set Top or Bottom Limit.

Remove a Favorite Position

Advanced Programming

IMPORTANT: Damage to shade may occur when operating the motor prior to setting limits. Attention should be given.

Switch between Roller and Window Shadings Mode

Adjust the Top and/or Bottom Limit

Factory Motor Reset

IMPORTANT: All limits will be erased. The motor direction will return to default and may need to be adjusted.

Reverse UP and DOWN Commands (Only if necessary)

Set Upper and Lower Limits ( Only after Factory Motor Reset)

Charge the Battery

When the shade begins to operate slower than normal or only beeps when you attempt to operate, it is time to charge the battery.
To Charge, connect a standard micro USB cable into the bottom of the wand (A) and into USB 5V/2A (max) power supply. A red LED on the wand indicates that the battery is charging. To fully charge the batteries, allow the batteries to charge for at least 1 hour after the LED on the wand turns green.

Note: A typical charge cycle can take between 4-6 hours.

Troubleshooting

Recharge with compatible USB 5V/2A (max) adapter and a micro USB cable. Details under “6. Charge the Battery”
Wand is not fully connected to the motor| Check the connection between the wand and the motor
The shade moves the opposite direction on the control buttons| The motor direction is reversed| See details under “Reverse Up and Down Commands”
The shade stops by itself before it reaches the top or bottom limit| A favorite position was set| See details under “4. Remove a Favorite Position”
**** The shade only moves in small steps after pressing the button| The shade is operating on Window Shadings/ Dual Shades mode| Switch to Roller/Honeycomb mode by following the steps under “Switch between Roller and Window Shadings Mode”
The shade has no limit set| See details under “Set Upper and Lower Limits”

Child Safety

WARNING
Window Blind Cord Can STRANGLE Your Child. To prevent strangulation, purchase cordless products or products with inaccessible cords.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>