VTech EW780-3281-01 Pan and Tilt Video Baby Monitor User Guide

VTech EW780-3281-01 Pan and Tilt Video Baby Monitor

Product Information

Technical Specifications:

• Frequency control: Crystal controlled PLL synthesizer
• Transmit frequency: Baby unit – 2405 – 2475 MHz, Parent unit – 2405 – 2475 MHz
• Channels: 32
• Display: 5″ Color LCD (WQVGA 480×272 pixels)
• Effective Range: Maximum power allowed by FCC and IC. Actual range may vary based on environmental conditions
• Power requirements: Parent unit – 3.6V, 2600mAh, 9.36Wh Li-ion battery
• Power adapters: Baby unit – Output: 5V DC @ 1A, Parent unit – Output: 5V DC @ 1A

Important Safety Instructions:

1. Follow all warnings and instructions marked on the product.
2. Adult setup is required.
3. Do not install the baby unit above 6.5 feet (2 meters).
4. This product is not a substitute for proper adult supervision.
5. Avoid using near water sources.
6. Use only provided power adapters to prevent damage.
7. Ensure correct orientation of power adapter.
8. Unplug before cleaning and avoid liquid cleaners.
9. Avoid placing heavy items on power cords.
10. Operate only from indicated power sources.
11. Avoid overloading outlets or using extension cords.
12. Avoid placing on unstable surfaces.

Product Recycling:
Recycle this product when you are done with it. For more information, scan the QR code or visit vtechphones.com/recycle.

Certifications:
CONFORMS TO UL STD. 62368-1 CERTIFIED TO CSA STD. C22.2 NO.62368-1

Power Adapter Information:
Output: 5V DC 1A VTech Telecommunications Ltd. Model: VT05EUS05100 -OR- Jiangxi Jian Aohai Technology Co.,Ltd Model: A318-050100W-US2

Rechargeable Battery Information:
Zhuhai Great Power Energy Co., Ltd. Li-ion battery, 3.6V, 2600mAh, 9.36Wh; Model: ICR18650-2.6Ah-3.6V-1S1P

Product Usage Instructions

Setup Instructions:

1. Place the baby unit in the desired location within the nursery, ensuring it is not above 6.5 feet high.
2. Position the parent unit in a convenient location within range of the baby unit.
3. Ensure both units are connected to power using the provided adapters.
4. Follow the pairing instructions in the user manual to link the parent and baby units.

Operating Instructions:

1. To view the baby’s room, turn on the parent unit and adjust the settings as needed.
2. You can pan and tilt the camera remotely using the controls on the parent unit.
3. Monitor the audio and video feed to keep an eye on your baby from another room.
4. Adjust volume levels and display settings for optimal monitoring experience.

Maintenance Instructions:

1. Clean the units with a damp cloth as needed, ensuring they are unplugged from power sources.
2. Avoid placing heavy objects on the power cords to prevent damage.
3. Regularly check and replace batteries as necessary to maintain optimal performance.

Frequently Asked Questions (FAQ):

• Q: Can I use this product as a medical monitor?
  A: No, this product is intended for monitoring purposes only and should not be used as a medical device.

• Q: What should I do if I encounter connectivity issues between the parent and baby units?
  A: Try re-pairing the units following the instructions in the user manual. Ensure both units are within range of each other and free from interference.

• Q: How often should I charge the parent unit’s battery?
  A: It is recommended to fully charge the parent unit’s battery before initial use and recharge as needed based on usage patterns.

Technical specifications

• Frequency control Crystal controlled PLL synthesizer
• Transmit frequency Baby unit: 2405 – 2475 MHz
• Parent unit: 2405 – 2475 MHz
• Channels 32
• LCD 5” Color LCD (WQVGA 480×272 pixels)
• Nominal effective range Maximum power allowed by FCC and IC. Actual operating range may vary according to environmental conditions at the time of use.
• Power requirements Parent unit: 3.6V, 2600mAh, 9.36Wh Li-ion battery
  • Baby unit power adapter: Output: 5V DC @ 1A
  • Parent unit power adapter: Output: 5V DC @ 1A

Product Recycling

• Recycle this product when you are done with it.
• For more information, scan the QR code or visit vtechphones.com/recycle.

Specifications are subject to change without notice. © 2023 VTech Communications, Inc. All rights reserved. 09/23. VM934-X_QSG_US_V1.

Important safety instructions

The applied nameplate is located at the bottom of the baby unit’s base.
When using your equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury, including the following:

1. Follow all warnings and instructions marked on the product.

2. Adult setup is required.

3. CAUTION: Do not install the baby unit at a height above 6.5 feet (2 meters).

4. This product is intended as an aid. It is not a substitute for responsible and proper adult supervision and should not be used as such.

5. This product is not intended for use as a medical monitor.

6. Do not use this product near water, for example, near to a bath, sink, swimming pool or shower.

7. CAUTION: Use only the battery provided (if applicable). There may be a risk of explosion if a wrong type of battery is used for the parent unit. The battery cannot be subjected to high or low extreme temperature and low air pressure at high altitude during use, storage or transportation. Disposal of battery in fire or a hot oven, mechanically crushing or cutting the battery can result in an explosion. Leaving the battery in an extremely high temperature surrounding environment can result in an explosion or the leakage of flammable liquid of gas. Battery subjected to extremely low air pressure may result in an explosion or the leakage of flammable liquid or gas. Dispose of used battery according to the information in The RBRC seal.

8. Use only the power adapters included with this product. Incorrect power adapter polarity or voltage can seriously damage the product.
   Power adapter information:

9. Output: 5V DC 1A

10. VTech Telecommunications Ltd.

11. Model: VT05EUS05100 -ORJiangxi

12. Jian Aohai Technology Co.,Ltd

13. Model: A318-050100W-US2

14. Rechargeable battery information: Zhuhai Great Power Energy Co., Ltd.

15. Li-ion battery, 3.6V, 2600mAh, 9.36Wh; Model: ICR18650-2.6Ah-3.6V-1S1P

16. The power adapter is intended to be correctly oriented in a vertical or floor mount position. The prongs are not designed to hold the plug in place if it is plugged into a ceiling, under- the-table or cabinet outlet.

17. For pluggable equipment, the socket-outlet (power adapter) should be installed near the equipment and should be easily accessible.

18. Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.

19. Do not modify the power adapters or replace with other adapters, as this causes a hazardous situation.

20. Do not allow anything to rest on the power cords. Do not install this product where the cords may be walked on or crimped.

21. This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply in your home, consult your dealer or electricity supply provider.

22. Do not overload wall outlets or use an extension cord.

23. Do not place this product on an unstable table, shelf, stand or other unstable surfaces.

24. This product should not be placed in any area where proper ventilation is not provided. Slots and openings in the back or bottom of this product are provided for ventilation. To protect them from overheating, these openings must not be blocked by placing the product on a soft surface such as a bed, sofa or rug. This product should never be placed near or over a radiator or heat source.

25. Never push objects of any kind into this product through the slots because they may touch dangerous voltage points or create a short circuit. Never spill liquid of any kind on the product

26. To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized service facility. Disassembling or removing parts of the product other than via the battery door (if applicable) may expose you to dangerous voltages or other risks. Incorrect reassembling can cause electric shock when the product is subsequently used.

27. You should test the sound reception every time you turn on the units or move one of the components.

28. Periodically examine all components for damage.

29. There is a very low risk of privacy loss when using certain electronic devices, such as baby monitors, cordless telephones, etc. To protect your privacy, make sure the product has never been used before purchase, reset the baby monitor periodically by powering off and then powering on the units, and power off the baby monitor if you are not intending to use it for some time.

30. Children should be supervised to ensure that they do not play with the product.

31. The small parts of this monitor can be swallowed by babies or small children. Keep these parts out of reach of children.

32. The product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

Cautions

• Use and store the product at a temperature between 32oF (0oC) and 104oF (40oC).
• Mishandling batteries can cause burn, fire or explosion hazards.
• Batteries should not be exposed to excessive heat such as bright sunshine or fire.
• Do not expose the product to extreme cold, heat or direct sunlight. Do not put the product close to a heating source.
• Warning—Strangulation Hazard—Children have STRANGLED in cords. Keep this cord out of the reach of children (more than 3 ft (0.9m) away). Do not remove the warning label on the adapter cord.
• Never place the camera unit(s) inside the baby’s crib or playpen. Never cover the camera unit(s) or parent unit with anything such as a towel or a blanket.
• Other electronic products may cause interference with your camera unit. Try installing your camera unit as far away from these electronic devices as possible: wireless routers, radios, cellular telephones, intercoms, room monitors, televisions, personal computers, kitchen appliances and cordless telephones.

Precautions for users of implanted cardiac pacemakers
Cardiac pacemakers (applies only to digital cordless devices): Wireless Technology Research, LLC (WTR), an independent research entity, led a multidisciplinary evaluation of the interference between portable wireless devices and implanted cardiac pacemakers. Supported by the U.S. Food and Drug Administration, WTR recommends to physicians that:

Pacemaker patients

• Should keep wireless devices at least six inches from the pacemaker.
• Should NOT place wireless devices directly over the pacemaker, such as in a breast pocket, when it is turned ON. WTR’s evaluation did not identify any risk to bystanders with pacemakers from other persons using wireless devices.

Electromagnetic fields (EMF)
This VTech product complies with all standards regarding electromagnetic fields (EMF). If handled properly and according to the instructions in this user’s manual, the product is safe to be used based on scientific evidence available today.

What’s in the box

Connect the baby monitor

The parent unit turns on automatically after connecting the power adapter to the power socket and the battery LED light illuminates for a few seconds, then turns off.

NOTES

• The rechargeable battery in the parent unit is built-in.
• Use only the power adapters supplied with this product.
• Make sure the parent unit and the baby unit are not connected to an electronically controlled electric power outlet.
• Connect the power adapters in a vertical or floor mount position only. The adapters’ prongs are not designed to hold the weight of baby monitors, so do not connect them to any ceiling, under-the-table, or cabinet outlets. Otherwise, the adapters may not properly connect to the outlets.
• Make sure the parent unit, the baby units and the power adapter cords are out of reach of children.

Charge the parent unit battery
When you have connected and turned the parent unit on, the battery charges automatically. NNOoTtEeSs

• Before using the baby monitor for the first time, charge the parent unit battery for 12 hours. When the parent unit battery is fully charged, the battery icon segments are solid .
• It takes longer to charge the battery when the parent unit is turned on. To shorten the charging time, turn the parent unit off while charging.
• The standby time varies depending on the sensitivity level you set, your actual use and the age of the battery.
  The battery icon indicates the battery status (see the following table ).

Power on or off the baby monitor

1. Slide the ON/OFF switch to power on or off your baby unit.
2. Press and hold POWER to power on or off your parent unit.

Positioning the baby monitor

Caution
Keep the baby unit out of the reach of your baby. Never place or mount the baby unit inside the baby’s crib or playpen

Caution
The default volume of your parent unit is level 3, and the maximum volume is level 5. If you experience feedback noise from your baby monitor while positioning:

• Make sure your baby unit and parent unit are more than 3 feet (1 meter) apart, OR
• Turn down the volume of your parent unit.

NOTES
To avoid interference from other electronic devices, place your baby monitor at least 3 feet (1 meter) away from devices such as wireless routers, microwaves, mobile phones and computers

Status check

• Once you power on both your baby unit and parent unit, your parent unit displays an image from the baby unit, and the LINK LED light turns on.
• The baby unit’s POWER LED light turns on

Basic operation

Use the menu
Press to enter the menu, choose a menu item, or save a setting. You can use the parent unit for advanced settings or operations, such as to play or stop the baby unit lullaby, or to adjust the baby unit sound sensitivity.

While in the menu:

• Press to scroll among the menu options.
• Press to select an item, or to save a setting.
• Press to scroll among the sub-menus, or to adjust a setting.
• Press to return to the previous menu options without changing the current setting.
• Press TALK to return to live video.

Talk to your baby unit
Press and hold TALK and speak to your parent unit. Your voice is transmitted to the baby unit. Release TALK when finished talking and hear your baby again.

Turn off the screen
Press POWER to turn off the parent unit screen without powering off the parent unit. You will still hear sounds from the baby unit.

Adjust parent unit volume
Press VOL – / VOL + to adjust your parent unit speaker volume.

Zoom

1. Press to enter the menu.
2. Press to select , then press to confirm.
3. Press to choose either , depending on how many  times you want to zoom in, then press to confirm .

Overview

Parent unit

1. Antenna
2. 3-level sound indicator  light
3. Battery LED light
4. LINK LED light
5. Arrow keys
6. MENU /SELECT
7. RETURN/TALK
8. LCD off/POWER key
9. VOL – / VOL +
10. Power jack
11. RESET
12. Speaker

Baby unit

1. Light sensor

2. Camera lens

3. Microphone

4. Infrared LEDs
   Allow you to see clearly in a dark environment.

5. Night light

6. Night Light Control Key
   Tap to turn the night light on or off.

7. ON/OFF switch

8. POWER LED light

9. Speaker

10. Power jack

11. Temperature sensor

12. Slots for wall mounting

13. PAIR/RESET key
    The parent unit and baby unit(s) provided are already paired.

Need help?

For operations and guides to help you use your video monitor, and for the latest information and support, check out our online help topics and online FAQs.
Use your smartphone or mobile device to access our online help.

• Go to https://help.vtechphones.com/vm934 or https://help.vtechphones.com/vm934-2; OR
• Scan the QR code on the right. Launch the camera app or QR code scanner app on your smartphone or tablet. Hold the device’s camera up to the QR code and frame it. Tap the notification to be redirected to the online help page.
  • If the QR code is not clearly displayed, adjust your camera’s focus by moving your device closer or further away until it is clear.

You can also call our Customer Support at 1 800-595-9511 [in US] or 1 800-267-7377 [in Canada] for help.

Parent unit icons

Go to www.vtechphones.com to register your product for enhanced warranty support and the latest VTech product news
VM934 VM934-2  Pan and Tilt Video Baby Monitor

For more support information

Documents / Resources

| VTech EW780-3281-01 Pan and Tilt Video Baby Monitor [pdf] User Guide
EW780-3281-01 Pan and Tilt Video Baby Monitor, EW780-3281-01, Pan and Tilt Video Baby Monitor, Tilt Video Baby Monitor, Video Baby Monitor, Baby Monitor, Monitor
---|---

References

• VTech Cordless Phones Official Site | Best Home Office & Business Phones
• VTech Cordless Phones Official Site | Best Home Office & Business Phones
• Product Support | VTech® Cordless Phones
• Product Support | VTech® Cordless Phones

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>