850W Galaxy Power User Manual
- June 1, 2024
- Galaxy
Table of Contents
850W Galaxy Power
Product Features
- ATX3.0 / PCleS.0 modular power supply
- 80+ GOLD certified for 90%+ efficiency
- Stable and reliable.
- Cosmic black casing
- Supports single 12v output for higher power usage
- Supports Dual/ Quad/ Multi core CPU’S
- Ample +12V output, enhanced +12V current capability broadens utilization possibilities.
- Multi CPU technologies supported, 6 pin/ 8 pin/ 12+4 pin PCle 5.0 12VHPWR connectors to support all GPU platforms
- Built in lx 135mm silent automatically thermal fan speed controlled black fan.
- Dimensions: 150mm x158mm x 86mm (5.9″x 6.2″x 3.4″) W x L x H
- Heavy-duty protections, including OVP (Over Voltage Protection) OPP (Over Power Protection), SCP (Short Circuit Protection)
- Built-in APFC (Active Power Factor Correction) rates> 0.9
- DC to DC converter design, provides superior dynamic response, greater system
- stability and maximizes the 12V DC rail output
Product Specifications
- AC input voltage: 100-240V
- AC input frequency: 60Hz/50Hz
- Operating temperature: The power supply should be operated in an ambient temperature of 0°C to 40°C
- DC output:
Overall Performance:
- Hold up time: 14ms at full load normal line input voltage.
- Switching frequency: 50KHz at normal line input.
- Stability: +/- 5% for 24KHR after warm up.
Protections:
-
Under voltage protection.
If an under voltage fault occurs, the supply will latch all DC outputs into a shutdown state when +12V,+5V & +3.3V outputs under 60% of its maximum value. -
Over voltage protection
-
Short circuit
An output short circuit is defined as any output impedance less than 0.1 ohms. The power supply shall shut down and latch off for shorting the +3.3 VDC,+5 VDCor+l2 VDC rails. Shorts between main output rails and +5VSB shall not cause any damage to the power supply. The power supply shall either shut down and latch off or fold back for shorting the negative rails.+5VSB must be capable of being shorted indefinitely, but when the short is removed, the power supply shall recover automatically or by cycling PS_ON#. The power supply shall be capable of withstanding a continuous short-circuit to the output without damage or overstress to the unit. -
Over-power protection
The power supply will be shut down and latch off when output power is llQ%~1s0%
Dimensions:
150mm x 158mm x 86mm (5.9″” x 6.2″” x 3.4″”) W x L x H
Description of Connectors:
850W / 1000W semi-modular
1200W full-modular
Precautions:
Warning! To avoid the risk of electrical shock, unauthorized persons need the following precautions:
- Do not open the power supply case!
- Avoid exposure to humidity.
Information:
- Thank you for purchasing a high-quality Apevia product! Please visit our website at
http://www.apevia.com for complete warranty information and future support for your product. For the latest release information, or should you have any questions, please visit our website, or contact us at:
Support Phone Number: 1-909-718-0789
Support E-mail: support@apevia.com
Installation
-
Plug the 24-pin connector onto the motherboard.
-
4-pin or 8-pin (4+4pin) + 12V connector used for CPU only.
-
PCle 5.0 connector to the most advanced graphics cards
-
PCI express connector for video card only.
-
pin molex connectors used for hard drive, CD-ROM and cooling fans.
-
SATA connectors used for SATA hard drives.
Troubleshooting:
If power supply fails to operate properly, please check the following before requesting for an RMA:
- Please make sure the power supply and power cord is connected properly.
- Please make sure the power cord is plugged into the power socket.
- Please make sure the power supply 1/0 button is switched to the “!” position.
- Please check if all the connectors (motherboard, floppy and peripherals) are connected properly.
- Please allow 5 seconds interval before turning the power on again when power supply is switched off manually (setting the 1/0 switch to the “0” position)
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>