PROGRESS LIGHTING P500434-31M Rivera 1 Light 4.75 inch Matte Black Mini Pendant Ceiling Light Instruction Manual

PROGRESS LIGHTING P500434-31M Rivera 1 Light 4.75 inch Matte Black Mini Pendant Ceiling Light Instruction Manual

PACKAGE CONTENTS

HARDWARE CONTENTS (not actual size)

| | | | | | | | | |
---|---|---|---|---|---|---|---|---|---|---
Screw (#8-32) Qty:2| Wire Nut Qty:3| Round Mounting Plate Qty:1| Hex Nut (#8-32) Qty:2| Cylinder Nut (#8-32) Qty:2|  Chain (3 links) Qty:1| Chain Loop (1/8IP) Qty:2| 12″ Pipe (1/8IP) Qty:4| 6″ Pipe (1/8IP) Qty:1| Nipple (1/8IP) Qty:4| Quick link Qty:1

Safety Information

Please read and understand this entire manual before attempting to assemble, operate or install the product.

CAUTION: Read instructions carefully and turn electricity off at main circuit breaker panel before beginning installation.

CAUTION: Risk of fire, Min, 90°C supply conductors, Consult a qualified electrician to ensure correct branch circult conductor.

WARNING: If any Special Control Devices are used with this fixture, follow Instructions carefully to assure full compllance with N.E.C. requirements. If there are any questions, contact a qualified electrical contractor.

CAUTION: All glass is fragile. Use care when handling glass shades and bulbs.

Preparation

1. Before beginning Installation, make sure all parts are Included using the contents diagrams from page 1. If any part is missing or damaged, do not attempt to assemble, Install or operate the product.
2. Estimated assembly time: 30 minutes.
3. Tools required for assembly (not Included): Phillips screwdriver, pullers, wire stripper, safety glasses, electrical tape, ladder.

Care and Maintenance

Shut off main power supply before cleaning product or changing light bulbs. To clean, wipe with damp cloth. Do not use abrasive dealers or cleaners that contain alcohol.

Assembly Instructions

1. Loosely thread the screws (AA) and the hex nuts (DD) onto the round mounting plate (CC) as shown. You now need to adjust the screw length according to the fixture canopy depth.
   

2. Attach this assembly to the outlet box using the mounting. screws supplied with the outlet box (not  provided). Tighten securely.
   
   Lift up the fixture and pass the screws (AA) through the two mounting hole in the fixture canopy. While holding the fixture with one hand, thread the screws (AA) in or out of the round mounting plate (CC) until 3/16″ of threads are showing. That should be enough to mount the fixture as instructed in step 4.
   Next, take the fixture down and go back and tighten the hex nuts (DD) up against the round mounting plate (CC). You now should have the correct length of threads for mounting the fixture.
   

3. Attach the glass panels (C) to the fixture (A) and the bottom frame (D), by aligning the two holies in the glass panel (C) with the holes in the fixture (A) and bottom frame (D). Use the screws (B) to secure tightly.
   NOTE: During this step, determine the hanging length of your fixture by adding or removing stems and chain links. The electrical and ground wire may also optionally be cut to length.
   Do NOT cut electrical or ground wires until this length is determined. Leave AT LEAST 6 inches MINIMUM of wire past the canopy chain loop (GG) to allow for easy connections in step 5.
   (Chain links can be spread open with 2 pairs of pliers. Twist the split link ends in opposite directions and close by squeezing them back together.)
   

4. Once hanging length is determined, pass wires through pipes (HH), pipe (JJ), nipples (KK), chain loop (GG), tightening pipes to assembly as you go to avoid twisting the wires. Tighten one end of pipes assembly (HH) to the fixture (A), other end to the chain loop (GG).
   Open chain link at one end of chain (FF). Hook the open chain link (FF) onto the chain loop (GG). Close the chain links back together with the pliers.
   Open the quick link (LL). Hook the quick link (LL) onto the other end of chain (FF) and the canopy loop (E). Close the quick link (LL) and secure it tightly.
   You can now weave the wire through every chain link (FF). Continue to pass the wires through the chain loop (GG) and up through the canopy (E).
   

5. Strip 3/8″ of insulation from the electrical wire ends. Using wire nuts (BB), connect RIBBED fixture wire to the WHITE supply wire from the outlet box; connect the SMOOTH fixture wire to the BLACK supply wire.
   Connect the fixture ground wire and supply ground wire using a wire nut or by fastening to the ground
   screw on the round mounting plate. Push all wire connections into the outlet box.
   

6. Pass the screws through the two holes in the canopy. Secure the fixture (A) to the screws (AA) using the  two cylinder nuts (EE) provided. Tighten securely in place.
   

7. Thread the lamp (not included) into the fixture socket. Use 60-watt MAX incandescent medium base lamp, SBCFL or SBLED.
   

WARRANTY AND EXCLUSIVE REMEDY

Progress products, when properly installed and under normal conditions of use, are warranted to our customers only to be free from defects in material and workmanship at time of shipment. All warranty claims must be asserted within one year from date of purchase of the subject items; thereafter, warranty claims will not be honored. Customers’ sole remedy for a warranty claim or otherwise shall be limited to repair or replacement of the subject product if it is shown to have been defective in material or workmanship at time of shipment. Progress’s sole and maximum liability for a defective product shall never exceed the cost of the subject product. EXCEPT FOR SUCH A WARRANTY AND EXCLUSIVE REMEDY AS STATED (AND THE EXPRESS WARRANTY OF TITLE), WE DISCLAIM ALL OTHER WARRANTIES, WHETHER EXPRESS OR IMPLIED, AND SPECIFICALLY DISCLAIM THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL WE BE LIABLE TO CUSTOMER IN WARRANTY, CONTRACT, NEGLIGENCE, STRICT LIABILITY OR OTHERWISE, FOR ANY DAMAGES, WHETHER INCIDENTAL OR CONSEQUENTIAL, WHICH ARE ALLEGED TO BE CAUSED BY ONE OR MORE OF OUR PRODUCTS, BEYOND THE COST TO THE CUSTOMER OF THE SUBJECT PRODUCT OR PRODUCTS. Therefore, the customer’s sole and exclusive remedy against us for breach of the warranty, breach of contract or negligence or strict liability or otherwise shall be limited to repair or replacement of the subject product at our option (excluding installation and removal charges which shall not be our liability) or, if we choose, refund of the purchase price. In no case does our warranty and exclusive remedy extend to anybody other than our customers. Our customers are not authorized to extend warranties or remedies on our behalf to anyone. Such unauthorized extensions of warranties or remedies by the customer shall remain customer’s responsibility. Customer is responsible for determining the suitability of our products for customer’s use or resale, or for incorporating them into objects or for applications which customer designs, assembles, constructs or manufactures.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>