PLATE HOLDER V1 Light Bracket Instruction Manual
- June 1, 2024
- PLATE HOLDER
Table of Contents
PLATE HOLDER V1 Light Bracket
Specifications
- Product Name: Placeholder V1
- Manufacturer: Placeholder GmbH
- Material: Plastic
- Compatibility: Universal fit for license plates
Product Usage Instructions
Mounting Criteria:
Ensure that the contact surface of the vehicle is flat. Use the centre hole and two slotted holes for mounting. Hand-tighten screws to avoid the bending of plastic. Mount the plate holders at least 4 cm per side from the license plate edge.
Mounting Instructions:
- Unpack the packaging and remove 2 plate holders.
- Check the vehicle holes and take out 2 or 4 screws accordingly.
- For vehicles with one hole on each side, use 2 screws; for two holes on each side, use 4 screws.
- Screw plate holders onto the vehicle, avoiding overtightening to prevent plastic damage.
- Insert the lower side of the license plate horizontally into the plate holder’s lower retaining lugs.
- Press the top of the license plate against the retaining tabs on each side until you hear a click.
- Aluminum plates will produce two clicks, while 3D plates will produce one click.
- Before using the vehicle, ensure the license plate is securely in place.
FAQ
- Q: What should I do if my license plate is not fitting securely?
- A: Check if the mounting criteria are met and ensure proper alignment and screw tightness. If issues persist, contact customer support for assistance.
- Q: Can I use Plateholder V1 for all types of vehicles?
- A: Placeholder V1 is designed for universal fit; however, ensure compatibility with your specific vehicle before installation.
MOUNTING INSTRUCTIONS
Ensure that the contact surface of the vehicle is flat. Both the centre hole and the two other slotted holes can be used \for mounting. It is important that the plastic does not bend when the screw is tightened. It should be hand- tightened. It is recommended to mount the plate holders at a distance of at least 4 cm per side from the edge of the license plate. [Caution: Incorrect mounting may result in the loss of the license plate.]
Mounting criteria
The consumer must ensure that the license plate is mounted in accordance with UN R 26.04. The following criteria must be taken into account for all four outer edges of the license plate:
- If the outer edges of the mounted license plate cannot be touched by a ball with a diameter of 100 mm, no further precautions need to be taken. (UNR26 point 5.1.3 and point 6.15)
- Since the rounding radii of a license plate are less than 2.5 mm and the edges are broken, the outer edges must not protrude more than 5 mm from the outer contour of the vehicle. (UN-R26 point 5.4)
- If these points cannot be met due to the vehicle geometry, the affected license plate edges must also be covered in such a way that the rounding radius is at least 2.5 mm.
INSTRUCTION
- unpack the packaging and remove 2 of the 4 plate holders.
- check the holes on the vehicle and remove 2 or 4 screws from the packaging accordingly.
- if your vehicle has only one hole on each side, use only 2 screws. If there are two holes on each side, use 4 screws for mounting.
- screw the plate holders to your vehicle, but do not overtighten the screws so that the plastic is not overloaded.
- take the license plate and insert the lower side of the license plate horizontally into the lower retaining lugs of the plate holder.
- press the top of the license plate against the retaining tabs on each side with both thumbs until you hear a click.
- If your license plate is an aluminium license plate, you will have two clicks. With 3D license plates, you will only hear one click.
- before using the vehicle, check that the license plate is securely and firmly in place.
Align the placeholder
Tighten the screws
Clip in the license plate
Nimm dir bitte 2 Minuten Zeit..
-
Social Media Kanäle: plateholder.de/linktree
