THUNDER LASER Aurora Lite Machine User Manual
- August 27, 2024
- THUNDER LASER
Table of Contents
Aurora Lite Machine
Product: Aurora Lite
Specifications:
- Manufacturer: Thunder Laser
- Model: Aurora Lite
- Product Type: Laser system
- Country of Origin: China
- Contact Information: tech@thunderlaser.com, Tel:(86)
18103043363
Product Information:
The Aurora Lite user manual provides detailed instructions for
the installation, operation, and maintenance of Thunder Laser
systems and fiber laser machines. It covers general information,
safety instructions, key components, installation steps, operation
guidelines, and maintenance procedures.
Usage Instructions:
1. General Information:
Read through the entire manual to understand the requirements
and guidelines for proper installation and usage of the Aurora
Lite.
2. Safety Instructions:
Follow all safety guidelines provided in the manual to ensure
safe operation of the laser system.
3. Process of Installing:
Follow the step-by-step installation instructions outlined in
Chapter 3 of the manual to set up the Aurora Lite properly.
4. Operation:
Refer to Chapter 4 for details on the machine view and how to
use the display for operating the Aurora Lite.
5. Brief Introduction to Softwares:
Chapter 5 provides an overview of the software used with the
Aurora Lite for laser processing.
6. How to Focus:
Chapter 6 offers guidance on how to focus the laser beam for
optimal performance.
FAQ:
Q: What should I do if I encounter issues during
installation?
A: If you face any problems during
installation, contact our technical personnel or Customer Service
for assistance. Avoid improper installation to prevent performance
issues or damage to the machine.
USER’S MANUAL
AURORA LITE
AURORA LITE Unified User’s Manual
Thunder Laser
www.thunderlaser.com tech@thunderlaser.com
June 2024
DONGGUAN THUNDER LASER EQUIPMENT CO., LTD
Dongguan City, Guangdong Province, China
www.thunderlaser.com tech@thunderlaser.com Tel:(86) 18103043363
DONGGUAN THUNDER LASER EQUIPMENT CO.,LTD
1
Room1101, Building 3, No.68, Xingzhou Road, Shatian
Town, Dongguan City, Guangdong Province, China
USER’S MANUAL
Introduction
AURORA LITE
This manual has been designated as a user’s guide for thunder laser systems and fiber laser machine installation; The manual is divided into eight chapters, including General Information Instructions, Safety Instructions, Key Components of every Laser Systems and the Installation Steps, Operation Instructions and Maintenance Instructions from THUNDERLASER Company.
It should be emphasized that the installation of each system must meet the requirements, and be consistent with the installation requirements of THUNDERLASER. If not, the machine won’t work properly, manifested as poor performance, shortened life-span, increasing maintenance costs and even damage to the machine.
The note is about some specific requirements during system installation, and we hope every customer could try to understand these notes before installation and usage, so that you can correctly install and use it. If you meet any problems during installation, you can contact our technical personnel or Customer Service.
www.thunderlaser.com tech@thunderlaser.com Tel:(86) 18103043363
DONGGUAN THUNDER LASER EQUIPMENT CO.,LTD
2
Room1101, Building 3, No.68, Xingzhou Road, Shatian
Town, Dongguan City, Guangdong Province, China
Content
USER’S MANUAL
AURORA LITE
CHAPTER 1. GENERAL ………………………………………………………………………………………………………………………………………………………..
4
1.1 GENERAL INFORMATION
…………………………………………………………………………………………………………………………………………………………………… 4 1.2
DESIGNATED
……………………………………………………………………………………………………………………………………………………………………………………..5 1.3
DISPOSAL
REMARKS…………………………………………………………………………………………………………………………………………………………………………..5 1.4
TECHNICAL PARAMETER/DEVICE SPECIFICATION
………………………………………………………………………………………………………………………………..6 1.5 MANUFACTURER’S
LABEL…………………………………………………………………………………………………………………………………………………………………..8
CHAPTER 2. SAFETY ……………………………………………………………………………………………………………………………………………………………
9
2.1 GENERAL SAFETY
INFORMATION………………………………………………………………………………………………………………………………………………………. 9 2.2
LASER SAFETY INFORMATION
…………………………………………………………………………………………………………………………………………………………. 10 2.3 SAFETY
PRECAUTIONS WHEN OPERATING THE DEVICE
……………………………………………………………………………………………………………………. 11 2.4 WARNING AND INFORMATION
LABELS …………………………………………………………………………………………………………………………………………… 12
CHAPTER 3. PROCESS OF INSTALLING
……………………………………………………………………………………………………………………………14
3.1 UNPACKING
…………………………………………………………………………………………………………………………………………………………………………………… 14 3.2
LOCATION………………………………………………………………………………………………………………………………………………………………………………………
14 3.3
CONNECTIONS………………………………………………………………………………………………………………………………………………………………………………..16
3.3.1 Connecting the
Mains……………………………………………………………………………………………………………………………………………………….. 16 3.3.2
Connecting the Computer
…………………………………………………………………………………………………………………………………………………17 3.3.3 Connecting the
exhaust system ………………………………………………………………………………………………………………………………………..17
CHAPTER 4. OPERATION
………………………………………………………………………………………………………………………………………………….19
4.1 MACHINE
VIEW……………………………………………………………………………………………………………………………………………………………………………….19 4.2
HOW TO USE THE DISPLAY
………………………………………………………………………………………………………………………………………………………………21
CHAPTER 5. BRIEF INTRODUCTION TO SOFTWARES
…………………………………………………………………………………………………….22
5.1 EZCAD2
………………………………………………………………………………………………………………………………………………………………………………………. 22
5.1.1 Driver
Installation……………………………………………………………………………………………………………………………………………………………….. 23
5.1.2 Software setting
…………………………………………………………………………………………………………………………………………………………………..28
CHAPTER 6. HOW TO FOCUS …………………………………………………………………………………………………………………………………………30
CHAPTER 7 THE FIRST TIME TO RUN THE FIBER LASER
……………………………………………………………………………………………….. 32
CHAPTER 8 MAINTENANCE …………………………………………………………………………………………………………………………………………….
38
8.1 GENERAL MAINTENANCE
……………………………………………………………………………………………………………………………………………………………….. 38 8.2 CLEAN
THE FIELD LENS
……………………………………………………………………………………………………………………………………………………………………38
www.thunderlaser.com tech@thunderlaser.com Tel:(86) 18103043363
DONGGUAN THUNDER LASER EQUIPMENT CO.,LTD
3
Room1101, Building 3, No.68, Xingzhou Road, Shatian
Town, Dongguan City, Guangdong Province, China
Chapter 1. General
USER’S MANUAL
AURORA LITE
1.1 General Information
Please read this documentation carefully before installation and operation.
Injury, death, property loss, fire, electric shock, malfunction, reduced
performance & machine
life-span, and serious failures might happen unless you read, understand, and follow the
Operation Manual!
Operation of the system is permitted only with equipment and spare parts supplied or listed in the List of Spare Parts and Consumables. The use of components from the 3rd Party may invalidate the warranty. Auxiliary equipment must be adjusted to the base machine (contact us for further info). The following symbols are used throughout the Operation Manual:
Caution: When operating the laser, keep alarmed all the time.
High Voltage: Be careful to prevent injury and/or death.
Laser Radiation: Keep away from the dangers of the laser beam.
Fire Hazard: High potential for fire. NEVER LEAVE IT UNATTENDED WHEN RUNNING!
Tips: Helpful notes or info can make it easier to use or understand.
www.thunderlaser.com tech@thunderlaser.com Tel:(86) 18103043363
DONGGUAN THUNDER LASER EQUIPMENT CO.,LTD
4
Room1101, Building 3, No.68, Xingzhou Road, Shatian
Town, Dongguan City, Guangdong Province, China
1.2 Designated
USER’S MANUAL
AURORA LITE
The THUNDER LASER AURORA LITE is intended exclusively for laser marking through the supplied marking software. Materials such as metal, anodized aluminum, and several plastics can be processed by the laser. As part of the intended use, the following points should also be observed:
1. The engraving process must only be performed with a perfectly adjusted
machine. 2. Only mark approved materials with suitable parameters. 3. Use of
the system in other areas is against the designated use. The manufacturer does
not admit liability for damage to personal and/or equipment resulting from
such use. 4. The system must only be operated, maintained and repaired, by
personnel that are familiar with the designated field of use and the dangers
of the machine! 5. Non-observance of the instructions for operation,
maintenance and repair described in this operation Manual excludes any
liability of the manufacturer if a defect occurs. 6. Caution when processing
conductive materials (carbon fibers), conductive dust or particles in the
ambient air might damage electrical components and lead to short circuits.
Bear in mind that those defects are not warranted.
1.3 Disposal remarks
Do not dispose the machine with house refuse! Electronic devices have to be disposed along with electric waste disposal according to the regional directives on electronic. For further questions, please ask your supplier. He might handle it properly.
www.thunderlaser.com tech@thunderlaser.com Tel:(86) 18103043363
DONGGUAN THUNDER LASER EQUIPMENT CO.,LTD
5
Room1101, Building 3, No.68, Xingzhou Road, Shatian
Town, Dongguan City, Guangdong Province, China
USER’S MANUAL 1.4 Technical Parameter/Device Specification
AURORA LITE
Mechanics
AURORA LITE
Max marking area
200*200mm/7.9
Max working area Lens(Fiber and Mopa)
Marking area
200*200mm/7.9
Max work height
Focus diameter
F-160 F-210 F-290
4.3×4.3/110×110mm 5.7×5.7/145×145mm 7.9×7.9/200×200mm
8.3/213mm 5.0/127mm 2.5/66mm
26µm 24µm 35µm
Max marking speed Z-axis
7000mm/sec, 700cps Motorized Z-axis, 16.9/430mm
Table
Alumina table, 14.7×11.3/375×288mm
Net weight
72.5kg/159.8lbs
Housing dimensions(WDH)
PS
16.9×29.7×31.4/430755799mm AURORA Lite is fitted with F-210 as standard.
Focus length 6.9/176mm 9.1/232.5mm 12.7/324mm
Laser Equipment
Laser power Wavelength Frequency Pulse width Q-pulse width
Cooling Red dot pointer
Control System
Computer Interfaces Marking software Correction software Laser power
AURORA LITE Fiber 50w 1064nm 50-100kHz / / Air cooled
Laser Power<1mW, 630-680nm
AURORA LITE Microsoft Windows XP, Win7, Win8, Win10,Win11
USB EzCad2/Lightburn
CorFile2 Fiber 50W adjustable from 10% – 100%
www.thunderlaser.com tech@thunderlaser.com Tel:(86) 18103043363
DONGGUAN THUNDER LASER EQUIPMENT CO.,LTD
6
Room1101, Building 3, No.68, Xingzhou Road, Shatian
Town, Dongguan City, Guangdong Province, China
Electricity, Power, Breaker
Electricity requirement Power consumption Current Recommended circuit breaker
Ambient Conditions Ambient temperature Humidity
Laser Safety Laser class
USER’S MANUAL
AURORA LITE
50WATT 115~240 Volt AC, 50 or 60Hz, Single phase
300W 2.55A,115V 1.5A,230V
10A
Operating temperature 0-40 Maximum humidity 80%
Class CE-Compliant approved by FDA
www.thunderlaser.com tech@thunderlaser.com Tel:(86) 18103043363
DONGGUAN THUNDER LASER EQUIPMENT CO.,LTD
7
Room1101, Building 3, No.68, Xingzhou Road, Shatian
Town, Dongguan City, Guangdong Province, China
1.5 Manufacturer’s Label
USER’S MANUAL
The Manufacturer’s Label is on the backside of the machine (see picture below)
AURORA LITE
It is recommended to record all of the data for access anywhere anytime. You will need to supply your Serial Number to our Support Team on occasion.
www.thunderlaser.com tech@thunderlaser.com Tel:(86) 18103043363
DONGGUAN THUNDER LASER EQUIPMENT CO.,LTD
8
Room1101, Building 3, No.68, Xingzhou Road, Shatian
Town, Dongguan City, Guangdong Province, China
Chapter 2. Safety
USER’S MANUAL
AURORA LITE
2.1 General Safety Information
Any personnel involved in installation, set-up, operation, maintenance and
repair of the machine, should have read and understood the Operation Manual,
particularly for the “Safety” section. The user is recommended to assign
specific company-internal personnel to implement each operation according to
the qualifications the employees. And the receipt of the instruction/Operation
Manual or the participation at introduction/training should be acknowledged in
writing in each case.
Safety -conscious working
The machine must only be operated by trained and authorized personnel. The
scopes of different applicable operations of the machine must be clarified and
observed in case of some problems related to safety. Especially for operations
on the electric equipment, which must be performed by special experts only.
For all manipulations concerning modifications, maintenance, inspection and
repair of installation, set-up, start-up, operation, conditions and operation
methods, the switch-off procedures that may be provided in the Operation
Manual must be observed.
Safety Information for the User and/or Operating Personnel
1. Any operating methods that will imperil the safety of the working machine are forbidden.
2. The operator must also ensure that no unauthorized person work with the
machine (e.g. activating equipment without authorization). 3. It is the duty
of the operator to check the machine before starting for externally-visible
damage or flaws, and to report changes (including behavior during operation)
that imperils the safety. 4. The user must ensure that the machine is only
operated in sound condition. 5. The user must guarantee the cleanness and
accessibility at and around the machine by
corresponding instructions and controls. 6. No removing or interrupting safety
components (we emphasize again the imminent dangers, for example severe burns,
loss of eyesight, etc.). If the removal of safety components is required
during repair and service, the replacement of the safety components must be
performed immediately after repairing.
www.thunderlaser.com tech@thunderlaser.com Tel:(86) 18103043363
DONGGUAN THUNDER LASER EQUIPMENT CO.,LTD
9
Room1101, Building 3, No.68, Xingzhou Road, Shatian
Town, Dongguan City, Guangdong Province, China
USER’S MANUAL
AURORA LITE
7. Preparation, retooling, change of workpiece, maintenance and repair must be performed only
with equipment switched off and by trained personnel.
8. Any attempt to perform unauthorized modifications and changes to the machine can
INVALIDATE THE WARRANTY. This does not conform to Thunder Laser’s routine preventive &
general maintenance, adjustment and alignment, etc.
2.2 Laser Safety Information
1. According to the assessment of the potential danger of the laser systems,
the machine is classified into SECURITY CLASS 2. Thunder Laser AURORA series
is a device of SECURITY CLASS 2, which is guaranteed by the protective housing
and the safety installations. Attention: Improper operation and maintenance of
the device can change the security level and cause the emission of harmful
radiation. 2. Without safety precautions, exposure to laser radiation will
cause the following risks: Eyes: Corneal burn Skin: Burns Clothing: Danger of
fire 3. Never try to modify or disassemble the laser or start up a modified or
disassembled system! 4. Other inappropriate operation or adjustment will cause
dangerous radiation exposure other than
those described here.
www.thunderlaser.com tech@thunderlaser.com Tel:(86) 18103043363
DONGGUAN THUNDER LASER EQUIPMENT CO.,LTD
10
Room1101, Building 3, No.68, Xingzhou Road, Shatian
Town, Dongguan City, Guangdong Province, China
USER’S MANUAL 2.3 Safety Precautions when Operating the Device
AURORA LITE
Your Thunder Laser AURORA SERIES has an integrated safety system which immediately stops running when the protection cover (Lid) is opened. Opening the cover during the operation will interrupt the engraving. Please remember the following safety precautions when working with this device:
1. CO2 Fire extinguishers should be placed near laser. Always keep a properly maintained and inspected fire extinguisher on hand. 2. Do not store any inflammables inside of the device. Particularly, leftovers of processed materials have to be removed to prevent fire hazard. 3. Please maintain free airflow around this system all the time. Do not cover the machine during operation. 4. Stay with the laser. Do not leave the laser unattended when it is working.
1. These lasers emit invisible radiation, so safety glasses should be worn when maintaining these machines for protection. 2. Adjustment of the beam path must be performed only by professionally trained personnel. Any non-standard setting can lead to uncontrollable emission of the laser radiation.
1. Do not disable limit switches or safety devices as this can invalidate warranties and cause damage to you and the machine. 2. Before processing, please verify whether harmful materials can be generated and whether the equipment for exhaust and filtration is useful in dealing with the harmful materials. We need to emphasize that it is the responsibility of the user to consider the national and regional boundary value (the maximum permitted emission concentration) for dust, fogs and gases when selecting the system for exhaust and filtration. 3. Under no circumstances can PVC (polyvinyl chloride) be processed with the laser.
www.thunderlaser.com tech@thunderlaser.com Tel:(86) 18103043363
DONGGUAN THUNDER LASER EQUIPMENT CO.,LTD
11
Room1101, Building 3, No.68, Xingzhou Road, Shatian
Town, Dongguan City, Guangdong Province, China
USER’S MANUAL 2.4 Warning and Information Labels
AURORA LITE
The warning and information labels in various locations of the machine should always be carefully read and understood. If labels are lost or damaged, they must be replaced immediately.
www.thunderlaser.com tech@thunderlaser.com Tel:(86) 18103043363
DONGGUAN THUNDER LASER EQUIPMENT CO.,LTD
12
Room1101, Building 3, No.68, Xingzhou Road, Shatian
Town, Dongguan City, Guangdong Province, China
USER’S MANUAL
AURORA LITE
www.thunderlaser.com tech@thunderlaser.com Tel:(86) 18103043363
DONGGUAN THUNDER LASER EQUIPMENT CO.,LTD
13
Room1101, Building 3, No.68, Xingzhou Road, Shatian
Town, Dongguan City, Guangdong Province, China
USER’S MANUAL
Chapter 3. Process of Installing
AURORA LITE
3.1 Unpacking
When you receive your THUNDER LASER AURORA SERIES, it’s packed in a wooden box which contains the laser machine and additional accessories. The steps for unpacking and assembling of the laser are as follows. Please follow them carefully.
Keep the packing box. You will need it in case of a return. Dispose all waste
according to the applicable waste disposal rules 1. Put the wooden box in a
flat and spacious room for unpacking. 2. Remove the machine box; carefully
remove the protective foam, wraps, films, etc. 3. Please keep the warranty
certificate as well as the model and serial number of the machine. If you need
tech support, please tell us these. 4. Then start to install the machine,
carefully following the instructions in this manual.
3.2 Location
Before installing the fiber laser system, you should select an appropriate
location. Follow the guidelines shown below:
1. Avoid locations of high temperature, much dust and high humidity. (The
humidity should be kept within 70% and the recommended operating environment
temperature range of the laser is 0-40.) 2. Avoid locations where the system
is exposed to mechanical shocks.
1. Circuit Breaker protection: Do not connect other devices on the same
circuit as that of the laser system. It requires a dedicated circuit. 2. DO
NOT open any of the machine’s access panels while the unit is plugged in.
Opening any panel may expose the operator to severe electric shock, invisible
laser radiation, mechanical pinch points, burns, blindness, and other hazards.
POWER OFF AND UNPLUG after using! 3. DO NOT make or break any electrical
connections to the system while the unit is turned on.
www.thunderlaser.com tech@thunderlaser.com Tel:(86) 18103043363
DONGGUAN THUNDER LASER EQUIPMENT CO.,LTD
14
Room1101, Building 3, No.68, Xingzhou Road, Shatian
Town, Dongguan City, Guangdong Province, China
USER’S MANUAL
AURORA LITE
1. Avoid locations with poor air circulation; select a location close to ventilation (if available). Select a location, whose room temperature is between 15 °C and 25°C (59°F 77° F). 2. This is fundamental to maintain consistent and reliable operation of a fiber laser and the machine itself. Avoid higher ambient temperatures and strong exposure of the engraver to strong sunlight. Use blinds, if needed. 3. Mechanical shock and vibration of the laser will have detrimental effects on the performance and life expectancy of the machine. It will manifest (over a period of time) with a noticeable decrease in performance and need for maintenance, even breakdown, possibly. Setting your Thunder Fiber Laser up in s suitable controlled temperature, dust free, moisture free, level, stable surface (a level concrete floor) with the recommended maintenance method is critical to the ongoing performance of the machine. It is also a premise for warranty.
www.thunderlaser.com tech@thunderlaser.com Tel:(86) 18103043363
DONGGUAN THUNDER LASER EQUIPMENT CO.,LTD
15
Room1101, Building 3, No.68, Xingzhou Road, Shatian
Town, Dongguan City, Guangdong Province, China
3.3 Connections
USER’S MANUAL
AURORA LITE
Perform the connections exactly in the order described; otherwise the static
electricity can damage your computer and/or the electronics of the laser
system.
3.3.1 Connecting the Mains
Connect one end of the mains cable with the connection socket at the rear side
of the laser device (see figures below) and the other end with a protected
power outlet. Mains voltage must correspond with the operating voltage (AC
110V~240V 50/60 Hz) see information on label beside the connection socket.
other.
Under no circumstances should you switch on the device if the voltages do not correspond with each
www.thunderlaser.com tech@thunderlaser.com Tel:(86) 18103043363
DONGGUAN THUNDER LASER EQUIPMENT CO.,LTD
16
Room1101, Building 3, No.68, Xingzhou Road, Shatian
Town, Dongguan City, Guangdong Province, China
USER’S MANUAL 3.3.2 Connecting the Computer
AURORA LITE
Connecting the computer and the machine by using the USB cable, as shown in the picture below:
About how to start to use software EzCad2, refer to chapter 5.1 EzCad2.
The USB cable is placed inside the toolbox.
3.3.3 Connecting the exhaust system
Insert one side of the gray exhaust pipe into the fan inlet and the other side
into the machine behind the exhaust tank. Insert one side of the other gray
exhaust pipe into the fan outlet and put the other side of the pipe outside
the operation room (If the machine is too far from the door of the room to
discharge the gas manufactured; then you might need a dust/fume filter, it can
keep good air quality of your working environment). Please refer to the
following pictures about how to install the exhaust pipe:
www.thunderlaser.com tech@thunderlaser.com Tel:(86) 18103043363
DONGGUAN THUNDER LASER EQUIPMENT CO.,LTD
17
Room1101, Building 3, No.68, Xingzhou Road, Shatian
Town, Dongguan City, Guangdong Province, China
USER’S MANUAL
AURORA LITE
The input voltage must correspond to the required range (AC 110V~240V 50/60 Hz) see information label beside the connection socket.
www.thunderlaser.com tech@thunderlaser.com Tel:(86) 18103043363
DONGGUAN THUNDER LASER EQUIPMENT CO.,LTD
18
Room1101, Building 3, No.68, Xingzhou Road, Shatian
Town, Dongguan City, Guangdong Province, China
Chapter 4. Operation
USER’S MANUAL
AURORA LITE
4.1 Machine view
1. Left side door On fiber laser, there are installed Z motor and Driver, Z
limit switches.
Please open this door for checking these parts, but you must pay attention to
the electric current.
2. Rotary connector Use to connect the rotary.
3. Exhaust hole This is for exhausting the fume.
4. Indicator light If fiber laser machine is running, the signal lamp is in
red light. If the laser machine is on standby, the signal lamp is in green
light.
5. Flap protection sensor This is where the switch for flap protection exist.
Laser will stop working once the cover is opened during working.
6. Emergency stop button Once there’s an accident during operation, please
press this button immediately. And then the laser power and motion power will
be cut off immediately.
7. Key switch To turning the machine on.
8. Operate panel Control Z-axis, galvo movement, etc.
9. F- lens You can replace the field lens by rotating it.
10. Dual red dot pointer For confirming the focal length.
11. Galvanometer Composed of two parts: optical scanning device and servo
control.
www.thunderlaser.com tech@thunderlaser.com Tel:(86) 18103043363
DONGGUAN THUNDER LASER EQUIPMENT CO.,LTD
19
Room1101, Building 3, No.68, Xingzhou Road, Shatian
Town, Dongguan City, Guangdong Province, China
12. Front door Close it to run a file.
USER’S MANUAL
13. Protection glass Protect eyes from laser reflection.
14. Pass-through door User can remove it to marking some longer objects
15. Cooling fan Cooling the electricity parts.
16. Exhaust hose Install the exhaust pipe.
17. PC connection port (USB) This USB is for connecting computer.
18. Main power socket To connect the main power.
19. Manufacture’s label The device information is listed, such as serial number, manufacturing date and etc.
20. Exhaust fan socket To connect the main power of exhaust fan.
AURORA LITE
www.thunderlaser.com tech@thunderlaser.com Tel:(86) 18103043363
DONGGUAN THUNDER LASER EQUIPMENT CO.,LTD
20
Room1101, Building 3, No.68, Xingzhou Road, Shatian
Town, Dongguan City, Guangdong Province, China
4.2 How to use the display
USER’S MANUAL
AURORA LITE
Auto and ON: Auto is red means that an automatic door is installed on the
laser, otherwise not. On is red means the laser is ready, flashing means the
laser needs to initialize. Auto and On are all off means the emergency is
pressed.
On button: Initialize button, user needs press this button after rebooting the
machine.
Fan mode switching: In standard mode, the exhaust fan will always on. In auto
mode, the fan will be on after marking.
Light button: Control the lighting of the work table, the light is divided
into four brightness (the brightest by default for the power on).
Z button: Control the galvo to move.
Door button: Control the front cover to open and close. For Aurora Lite, this
button is not working.
Auto focus button: Press it, the galvo will adjust the focal length
automatically. For Aurora Lite, this button is not working.
Start button: Press it to run the job.
www.thunderlaser.com tech@thunderlaser.com Tel:(86) 18103043363
DONGGUAN THUNDER LASER EQUIPMENT CO.,LTD
21
Room1101, Building 3, No.68, Xingzhou Road, Shatian
Town, Dongguan City, Guangdong Province, China
USER’S MANUAL
Chapter 5. Brief Introduction to Software
AURORA LITE
5.1 EzCad2
The EzCad2 software runs on a PC with 900 MHz CPU and 256 MB RAM at least. In
general, we recommend the fastest PC available. EzCad2 was developed in
Microsoft Windows XP and will run in Windows XP, WIN7, WIN10 and VISTA. The
installation of EzCad2 is very easy. Users just need to copy EzCad2 folder in
the Install FOLDER to hard disk, and then double click the Ezcad2.exe under
the EzCad2’s directory to run the software. If users run the software without
connecting the fiber laser, a caution will appear and the software will work
at demo state. In demo state, we can evaluate the software but we cannot save
files and cannot control the laser device.
The Software, Drive and Correction file are in the U-disk that came with the fiber machine.
www.thunderlaser.com tech@thunderlaser.com Tel:(86) 18103043363
DONGGUAN THUNDER LASER EQUIPMENT CO.,LTD
22
Room1101, Building 3, No.68, Xingzhou Road, Shatian
Town, Dongguan City, Guangdong Province, China
5.1.1 Driver Installation
USER’S MANUAL
Turn on the fiber laser. Connect your fiber laser with PC via USB cable.
AURORA LITE
Before moving on to the next step, please save the Driver file in the U- disk
to your computer, and remember where it is.
How to choose correct driver for fiber laser.
Driver of fiber
1. Go Manage>>Device manager>>Other devices>>USBLMCV2>>right click, Update driver>>Browse my computer for driver software>>Browse, and find the CV4 folder you saved from the U-disk that came with the fiber laser>>Select the CV4 driver>>Next>>Install, then the driver is installed successfully. See pictures below.
Pic1
www.thunderlaser.com tech@thunderlaser.com Tel:(86) 18103043363
DONGGUAN THUNDER LASER EQUIPMENT CO.,LTD
23
Room1101, Building 3, No.68, Xingzhou Road, Shatian
Town, Dongguan City, Guangdong Province, China
USER’S MANUAL
AURORA LITE
Pic2
Pic3
www.thunderlaser.com tech@thunderlaser.com Tel:(86) 18103043363
DONGGUAN THUNDER LASER EQUIPMENT CO.,LTD
24
Room1101, Building 3, No.68, Xingzhou Road, Shatian
Town, Dongguan City, Guangdong Province, China
USER’S MANUAL
AURORA LITE
Pic4
Pic5
www.thunderlaser.com tech@thunderlaser.com Tel:(86) 18103043363
DONGGUAN THUNDER LASER EQUIPMENT CO.,LTD
25
Room1101, Building 3, No.68, Xingzhou Road, Shatian
Town, Dongguan City, Guangdong Province, China
USER’S MANUAL
AURORA LITE
Pic6
Pic7
www.thunderlaser.com tech@thunderlaser.com Tel:(86) 18103043363
DONGGUAN THUNDER LASER EQUIPMENT CO.,LTD
26
Room1101, Building 3, No.68, Xingzhou Road, Shatian
Town, Dongguan City, Guangdong Province, China
USER’S MANUAL
AURORA LITE
Pic8
Pic9 Then, you can open the software now.
www.thunderlaser.com tech@thunderlaser.com Tel:(86) 18103043363
DONGGUAN THUNDER LASER EQUIPMENT CO.,LTD
27
Room1101, Building 3, No.68, Xingzhou Road, Shatian
Town, Dongguan City, Guangdong Province, China
5.1.2 Software setting
USER’S MANUAL
1. General setting Fiber Open the software, then press “F3” and select items according to the picture below. Laser type: Fiber PWM: Max PWM: 100 kHz, Min PWM: 50 kHz. Fiber serial: IPG_YLP Open Mo Delay: 8ms.
AURORA LITE
The frequency range for Aurora Lite laser source.
Fiber laser
50W
Frequency
50-100kHz
And we set all setting above before leaving the factory, so just check if these are correct. If not, change them according.
www.thunderlaser.com tech@thunderlaser.com Tel:(86) 18103043363
DONGGUAN THUNDER LASER EQUIPMENT CO.,LTD
28
Room1101, Building 3, No.68, Xingzhou Road, Shatian
Town, Dongguan City, Guangdong Province, China
2. How to import the calibration file
USER’S MANUAL
AURORA LITE
1. Before leaving the factory, we have done a correction test for each
machine and imported the calibration file to fiber software, so the customer
does not need to calibrate again. 2. Different field lenses have different
calibrate files and cannot be used randomly. 3. If you’ve purchased other
field lens with the fiber machine, we will prepare the calibration file and
put it in the U-disk too. 4. If you’ve purchased other field lens after the
machine left the factory, contact us to get the calibration file. Open the
software>>Press “F3” button>>Field>>find the calibration file (say the name
is150×150.cor) in the USB disk that came with the machine.
Customer can save the calibration file to computer from U-disk, and select it from computer.
www.thunderlaser.com tech@thunderlaser.com Tel:(86) 18103043363
DONGGUAN THUNDER LASER EQUIPMENT CO.,LTD
29
Room1101, Building 3, No.68, Xingzhou Road, Shatian
Town, Dongguan City, Guangdong Province, China
Chapter 6. How to focus
USER’S MANUAL
How to use the dual red dot focus function
1.Place the material under the dual red dot.
AURORA LITE
2.Using the Z-axis up and down buttons to focus two beams of focused red dot to the same point.
How to use manual focus tool
AURORA series marking machines can be equipped with 3 field lenses (F-160,
F-210, F-290) and the focal lengths of different field lenses are different.
After changing the field lens, the user needs to use the corresponding focus
tool.
www.thunderlaser.com tech@thunderlaser.com Tel:(86) 18103043363
DONGGUAN THUNDER LASER EQUIPMENT CO.,LTD
30
Room1101, Building 3, No.68, Xingzhou Road, Shatian
Town, Dongguan City, Guangdong Province, China
USER’S MANUAL
Find the Focus Tool for help to adjust the focus directly like below:
AURORA LITE
1 Focus Tool 2 Material 3 Working
Table
www.thunderlaser.com tech@thunderlaser.com Tel:(86) 18103043363
DONGGUAN THUNDER LASER EQUIPMENT CO.,LTD
31
Room1101, Building 3, No.68, Xingzhou Road, Shatian
Town, Dongguan City, Guangdong Province, China
USER’S MANUAL
Chapter 7 The First Time to Run the Fiber Laser
AURORA LITE
For your safety, never ever run the laser system unattended. Your first marking test ( AURORA Lite, Lens F-210) The following steps describe how to successfully engrave a pattern for the first time. Please follow the steps: 1. First ensure that the exhaust fan, computer and all mains are connected. 2. Turn on the key switch and emergency button.
3. Place the material on the working platform.
4. Open the software EzCad2, then install driver and import the calibration file according to Chapter 5.2 Please must follow the steps to turn on the machine Turn on the machine>> turn on the software, otherwise the software cannot connect with the machine. 5. Import your file to EzCad2
www.thunderlaser.com tech@thunderlaser.com Tel:(86) 18103043363
DONGGUAN THUNDER LASER EQUIPMENT CO.,LTD
32
Room1101, Building 3, No.68, Xingzhou Road, Shatian
Town, Dongguan City, Guangdong Province, China
USER’S MANUAL
AURORA LITE
This software supports these file types. Vector Files
Image Files
www.thunderlaser.com tech@thunderlaser.com Tel:(86) 18103043363
DONGGUAN THUNDER LASER EQUIPMENT CO.,LTD
33
Room1101, Building 3, No.68, Xingzhou Road, Shatian
Town, Dongguan City, Guangdong Province, China
USER’S MANUAL
AURORA LITE
6. Press “Hatch”, choose Hatch1(or you can choose the others as you need), set the Line space as 0.025mm (we recommend the range of 0.01-0.1mm), then press “OK”.
www.thunderlaser.com tech@thunderlaser.com Tel:(86) 18103043363
DONGGUAN THUNDER LASER EQUIPMENT CO.,LTD
34
Room1101, Building 3, No.68, Xingzhou Road, Shatian
Town, Dongguan City, Guangdong Province, China
USER’S MANUAL
AURORA LITE
7. Set the marking parameters for your file. Adjust parameters as needed (you need to unselect “use the default para” for changing the parameters). Set the Loop Count to 1, Speed to 1200mm/s, Frequency to 50KHz, Q-Pulse width to 5µs. Start TC(US) to 0, Laser Off TC(US) to120, End TC(US) to 100, Polygon TC(US) to 100. Other settings needn’t to change.
www.thunderlaser.com tech@thunderlaser.com Tel:(86) 18103043363
DONGGUAN THUNDER LASER EQUIPMENT CO.,LTD
35
Room1101, Building 3, No.68, Xingzhou Road, Shatian
Town, Dongguan City, Guangdong Province, China
USER’S MANUAL
AURORA LITE
8. You can see a red dot on the work area, which comes from the galvanometer. So please put your material
under the red dot, then Focus manually. Using the Z-axis up and down buttons to focus two beams of focused red
dot to the same point.Finally the focus distance adjustment is complete.
www.thunderlaser.com tech@thunderlaser.com Tel:(86) 18103043363
DONGGUAN THUNDER LASER EQUIPMENT CO.,LTD
36
Room1101, Building 3, No.68, Xingzhou Road, Shatian
Town, Dongguan City, Guangdong Province, China
USER’S MANUAL
AURORA LITE
9. Press Key F1 or Red(F1) in software, then fiber will virtually mark out
the size of your file. Adjust the position of your material according to the
red area. See pictures below.
10. Close the door and press Key F2 or Mark(F2) in software. Or press “start”
button to mark.
1. The controller can record the last file, if you want to run a file twice
or more, you can just press “Start” button of the fiber machine. 2. You can
start to mark with “Start” button also. 11. The laser will mark your image.
www.thunderlaser.com tech@thunderlaser.com Tel:(86) 18103043363
DONGGUAN THUNDER LASER EQUIPMENT CO.,LTD
37
Room1101, Building 3, No.68, Xingzhou Road, Shatian
Town, Dongguan City, Guangdong Province, China
Chapter 8 Maintenance
8.1 General Maintenance
USER’S MANUAL
AURORA LITE
Caution-Before any maintenance efforts takes place, ensure that the power supply has been cut off and the system is powered off. All maintenance efforts must be carried out according to the safety regulations. In order to ensure the maximum availability and lifespan of the system, we recommend that you regularly check the ventilation and keep the surrounding area clean. Lubricating the rotary It is suggested to add lubricant oil (or Rust Preventative Grease) to the chuck at least every two weeks.
8.2 Clean the Field lens
This system is equipped with high-quality optical components, which, under
normal operating conditions, are free for maintenance within their lifespan.
However, it may be necessary to clean output lenses, e.g. the scanner flat
field lens (f-theta objective) needs cleaning if it is covered in dust or
fumes. 1. Never touch the optical components with your fingers! Oily or dirty
hands may damage the surfaces of lens. 2. Do not use any tools or hard objects
to clean the surfaces. Scratches cannot be repaired. 3. Blow away large pieces
of dirt by blowing up a balloon.
www.thunderlaser.com tech@thunderlaser.com Tel:(86) 18103043363
DONGGUAN THUNDER LASER EQUIPMENT CO.,LTD
38
Room1101, Building 3, No.68, Xingzhou Road, Shatian
Town, Dongguan City, Guangdong Province, China
USER’S MANUAL
AURORA LITE
4. Spray the cleaning solution onto the Q-tip, and remove the remaining stains with it.
5. Distribute the cleaning fluid carefully by small circular motions. Start with the center of the lens and move outwards to the edge. Keep moving the Q-tip until the entire surface is clean. 6. Clean it again with a new clean and dry cotton swab. 7. Make sure that no water or stains remain on the surface of the lens after cleaning. 8. Do not wipe the lens with a dry cloth. 9. Do not exert any pressure on the lens. 10. Clean once half a year (depended on the usage).
The End.
www.thunderlaser.com tech@thunderlaser.com Tel:(86) 18103043363
DONGGUAN THUNDER LASER EQUIPMENT CO.,LTD
39
Room1101, Building 3, No.68, Xingzhou Road, Shatian
Town, Dongguan City, Guangdong Province, China
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>