behringer 902 Voltage Controlled Amplifier User Guide
- June 1, 2024
- Behringer
Table of Contents
behringer 902 Voltage Controlled Amplifier
Safety Instruction
- Please read and follow all instructions.
- Keep the apparatus away from water, except for outdoor products..
- Clean only with a dry cloth.
- Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
- Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including amplifiers) that produce heat.
- Use only attachments/accessories specified by the manufacturer.
- Use only specified carts, stands, tripods, brackets, or tables.Use caution to prevent tip-over when moving the cart/apparatus combination.
- Avoid installing in confined spaces like bookcases.
- Do not place near naked flame sources, such as lighted candles.
- Operating temperature range 5° to 45°C (41° to 113°F).
LEGAL DISCLAIMER
Music Tribe accepts no liability for any loss which may be suffered by any person who relies either wholly or in part upon any description,photograph, or statement contained herein. Technical specifications, appearances and other information are subject to change without notice. All trademarks are the property of their respective owners. Midas, Klark Teknik, Lab Gruppen, Lake, Tannoy, Turbosound, TC Electronic, TC Helicon, Behringer, Bugera, Aston Microphones and Coolaudio are trademarks or registered trademarks of Music Tribe Global Brands Ltd. © Music Tribe Global Brands Ltd. 2024 All rights reserved.
LIMITED WARRANTY
For the applicable warranty terms and conditions and additional information
regarding Music Tribe’s Limited Warranty, please see complete details online
at community. musictribe.com/support.
902 VOLTAGE CONTROLLED AMPLIFIER Controls
- CONTROL MODE (LIN/EXP) – rocker switch toggles between linear and logarithmic response modes.
- FIXED CONTROL VOLTAGE – knob allows you to manually set a control voltage.
- SIG IN – input jacks accept audio and control signals over cables with 3.5 mm TS connectors. These dual inputs allow the unit to amplify two signals simultaneously.
- SIG OUT – output jacks send out amplified audio and control signals over cables with 3.5 mm TS connectors.
- CONTROL INPUTS – accept control voltage signals from other modules to change the amplification level.
Power Connection
- Connect end P1 to the module socket.
- Connect end P2 to the power supply.
The 902 VCA comes with the required power cable for connecting to a standard Eurorack power supply system. Follow these steps to connect power to the module. It is easier to make these connections before the module has been mounted into a rack case.
- Turn the power supply or rack case power off and disconnect the power cable.
- Insert the 16-pin connector on the power cable into the socket on the power supply or rack case. The connector has a tab that will align with the gap in the socket, so it cannot be inserted incorrectly. If the power supply does not have a keyed socket, be sure to orient pin 1 (-12 V) with the red stripe on the cable.
- Insert the 10-pin connector into the socket on the back of the module. The connector has a tab that will align with the socket for correct orientation.
- After both ends of the power cable have been securely attached, you may mount the module in a case and turn on the power supply.
Installation
The necessary screws are included with the module for mounting in a Eurorack case. Connect the power cable before mounting. Depending on the rack case, there may be a series of fixed holes spaced 2 HP apart along the length of the case, or a track that allows individual threaded plates to slide along the length of the case. The free-moving threaded plates allow precise positioning of the module, but each plate should be positioned in the approximate relation to the mounting holes in your module before attaching the screws. Hold the module against the Eurorack rails so that each of the mounting holes are aligned with a threaded rail or threaded plate. Attach the screws part way to start, which will allow small adjustments to the positioning while you get them all aligned. After the final position has been established, tighten the screws down.
Specifications
- Controls
- Control Mode Rocker switch Linear / exponential, switchable
- Fixed Control Voltage 1 x rotary knob 0 – 6 V, selectable
- Signal Connections
- Signal in 2 x 3.5 mm TS jack, mono
- Impedance 9 kΩ unbalanced
- Signal out 2 x 3.5 mm TS jack, mono
- Impedance 1.1 kΩ unbalanced
- Output noise <-78 dBu @ unity gain, 22 Hz – 22 kHz
- Control inputs 3 x 3.5 mm TS jack, mono
- Impedance 100 kΩ unbalanced
- CV input range -6 V to +6 V
- Power
- Power supply Eurorack
- Current draw 50 mA (+12 V), 45 mA (-12 V)
- Physical
- Dimensions 40 x 129 x 35 mm (1.6 x 5.1 x 1.4″)
- Rack units 8 HP
- Weight 0.09 kg (0.20 lbs)
FEDERAL COMMUNICATIONS COMMISSION COMPLIANCE INFORMATION
Behringer
902 VOLTAGE CONTROLLED AMPLIFIER
Responsible Party Name: Music Tribe Commercial NV Inc.
Address : 122 E. 42nd St.1,
8th Floor NY, NY 10168,
United States
Email Address:legal@musictribe.com
902 VOLTAGE CONTROLLED AMPLIFIER
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Important information:
Changes or modifications to the equipment not expressly approved by Music
Tribe can void the user’s authority to use the equipment.
Hereby, Music Tribe declares that this product is in compliance with Directive 2014/30/EU, Directive 2011/65/EU and Amendment 2015/863/EU, Directive 2012/19/EU, Regulation 519/2012 REACH SVHC and Directive 1907/2006/EC.
Full text of EU DoC is available at https://community.musictribe.com/
EU Representative: Music Tribe Brands DK A/S
Address : Gammel Strand 44, DK-1202 København K, Denmark
UK Representative: Music Tribe Brands UK Ltd.
Address : 8th Floor, 20 Farringdon Street London EC4A 4AB, United Kingdom
Correct disposal of this product: This symbol indicates that this product must
not be disposed of with household waste, according to the WEEE Directive
(2012/19/EU) and your national law. This product should be taken to a
collection center licensed for the recycling of waste electrical and
electronic equipment (EEE). The mishandling of this type of waste could have a
possible negative impact on the environment and human health due to
potentially hazardous substances that are generally associated with EEE. At
the same time, your cooperation in the correct disposal of this product will
contribute to the efficient use of natural resources. For more information
about where you can take your waste equipment for recycling, please contact
your local city office, or your household waste collection service.
型 号: 902 VOLTAGE CONTROLLED AMPLIFIER 合成器与采样器
制造商: Music Tribe Commercial FZE –
Made in China 中国制造
CAN ICES–003 (B)/NMB–003 (B).
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>