Speakman S-2253 32 Spray Shower Head Instruction Manual
- June 1, 2024
- SPEAKMAN
Table of Contents
Speakman S-2253 32 Spray Shower Head
Product Information
Specifications
- Model: S-2253
- Max. Flow Rate: 2.5 gpm (9.5L/min)
- Min. Flow Rate: 2.0 gpm (7.6 L/min) @ 45psi
FOR USE WITH AUTOMATIC COMPENSATING VALVES RATED AT 7.6 L/MIN (2.0 GPM) OR LESS.
Product Usage Instructions
Tools and Supplies Needed:
- Thread Seal Tape
- Adjustable Wrench
Installation Steps:
- Apply Teflon Tape to the outlet side of the shower arm in a clockwise direction.
- Thread the Showerhead onto the shower arm by turning it clockwise. Tighten with an adjustable wrench.
- Turn the water supply on and check for leaks.
Safety Tips:
Cover your drain to prevent the loss of parts during installation.
Maintenance:
Regular maintenance is recommended to ensure optimal performance. Refer to the
manufacturer’s instructions for specific maintenance guidelines.
Warranty:
For warranty information, visit www.speakman.com.
FAQ
-
Q: What should I do if there are leaks after installation?
A: Check if all connections are tight and properly sealed. Reapply Teflon Tape if necessary and ensure the Showerhead is securely attached. -
Q: Can I use this product with a flow rate higher than the specified maximum?
A: It is not recommended as it may affect the product’s performance and longevity. Stick to the specified flow rates for optimal results.
MODELS
- S-2253
- S-2253-E2
- S-2253-E175
- S-2253-E15
TOOLS AND SUPPLIES
IMPORTANT
Be sure to read the instructions thoroughly before beginning installation. Do
not overtighten any connections or damage may occur. This showerhead has an
optimal operating range of 20-80 psi.
SAFETY TIPS
- Cover your drain to prevent loss of parts.
MAINTENANCE
- Periodic cleaning using mild soap and warm water will help keep your Showerhead’s appearance in its original condition.
- For best results, dry immediately with a soft, clean cloth. DO NOT USE harsh and/or abrasive cleaners.
- To help restore the finish, occasionally apply a non-abrasive wax to your showerhead body (follow manufacturers’ instructions).
- On CHROME PLATED SHOWER HEADS, a two (2) part white vinegar, and one (1) part water solution can be used to break down excessive mineral deposits on the sprays. Let the showerhead soak in the solution for about ½ hour then rinse thoroughly. Brush off any remaining mineral deposits if necessary.
- To reduce mineral build-up, turn the handle to the FLOOD position to let the water drain out after every use.
WARRANTY
Additional warranty information can be found at: www.speakman.com.
INSTALLATION
- Apply Teflon Tape to the outlet side of the shower arm in a clockwise direction.
- Thread the Showerhead onto the shower arm by turning it in a clockwise direction. Tighten with an adjustable wrench. Turn the water supply on and check for leaks.
- Adjust the spray pattern by rotating the side handle to the preferred Anystream® position.
ROUGH-IN DIMENSIONS
- Model: S-2253
- Max. Flow Rate: 2.5 gpm (9.5L/min)
- Min. Flow Rate: 2.0 gpm (7.6 L/min) @ 45psi
- FOR USE WITH AUTOMATIC COMPENSATING VALVES RATED AT 7.6 L/MIN (2.0 GPM) OR LESS.
- Model: S-2253-E2
- Max. Flow Rate: 2.0 gpm (7.6 L/min)
- Min. Flow Rate: 1.5 gpm (5.7 L/min) @ 45psi
- FOR USE WITH AUTOMATIC COMPENSATING VALVES RATED AT 6.6 L/MIN (1.75 GPM) OR LESS.
- Model: S-2253-E175
- Max. Flow Rate: 1.75 gpm (6.6 L/min)
- Min. Flow Rate: 1.3 gpm (4.9 L/min) @ 45psi
- FOR USE WITH AUTOMATIC COMPENSATING VALVES RATED AT 5.7 L/MIN (1.5 GPM) OR LESS.
- Model: S-2253-E15
- Max. Flow Rate: 1.5 gpm (5.7 L/min)
- Min. Flow Rate: 1.1 gpm (4.2 L/min) @ 45psi
- FOR USE WITH AUTOMATIC COMPENSATING VALVES RATED AT 5.2 L/MIN (1.37 GPM) OR LESS.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>