SPEAKMAN SE-4400 GravityFlo Portable Eyewash Instructions
- June 16, 2024
- SPEAKMAN
Table of Contents
INSTRUCTIONS FOR MODELS
SE-4400
GRA VITYFLO®
Por table Eyewash
IMPORTANT
ANSI Z358.1 requires that all self-contained eyewash units shall be visually
inspected weekly , unless the product is placed in environments with extreme
conditions that may affect the for m, fit, or function of the unit
(temperature, dir t, etc.). If this is the case, then the inspection should be
conducted more often as the end user deems necessar y . Speakman Company fur
nishes a testing record tag (91-0635) with each unit. On this tag, the date of
inspection and the inspectors’ initials should be noted. ANSI Z358.1 specifies
that the height of the spray heads is to be between 33”-45” from the floor .
The SE-4400 weighs approximately 100 lbs when filled.
Ensure the mounting sur face and mounting hardware (not supplied) can safely
hold a minimum ver tical load of 150 lbs. Be sure to read instructions
thoroughly before beginning installation. Do not over tighten any connections
or damage may occur . The unit should be full at all times, to achieve the
minimum 15 minute run time as stated by ANSI, in case of an emergency . Refill
the tank to full level after each activation.
SAFETY TIPS
The SE-4400 Por table Eyewash should be installed in close proximity to
potential accident areas. It should be clearly identified, free from
obstructions and easily accessible.
The SE-4400 shall be protected from freezing, direct sunlight, and shall not
be exposed to ambient temperatures exceeding 38 0 C (100 0 F).
MAINTENANCE
Occasional cleaning and disinfection is recommended. T o clean the inside of
unit, add 1/4 cup (2 fluid oz.) of Clorox Liquid Bleach to a full tank of
potable water .
Allow the mixture to penetrate for 15 minutes. Drain tank, and rinse
thoroughly several times with potable water . For fur ther infor mation about
Clorox Liquid Bleach, call toll-free at
1-800-292-2200. Follow refilling
instructions in this manual and place tank back in ser vice. Should any repair
par t be required, use only genuine SPEAKMAN par ts for repair or replacement.
See available replacement par ts on the final page of this manual. T o order
replacement par ts, please call toll-free at
1-800-537-2107
WARRANTY
3 Year Limited W arranty: Speakman Safety products are warranted to be
free of defects in material and workmanship for 3 years from date of
installation.
(“W arranty Period”) Speakman warrants to its purchases (“Buyer”) that goods
are sold free from defects in materials and workmanship and confor m to
Speakman’ s specifications at the time of manufacturing, provided the goods
are properly installed and maintained. Buyer’ s sole and exclusive remedy for
any goods that may prove to have had a non- ‐ confor mance within the W
arranty Period shall be, at Speakman’ s sole option, the repair or replacement
of the non- ‐ conforming goods
TOOLS AND SUPPLIES
-
Select a suitable mounting location for the SE-4400 capable of suppor ting 150 lbs. The location should protect the unit from freezing and potential scalding conditions. Place mounting bracket on sur face so the top of the 3/8” mounting bracket is located between 58 3/8” – 69 3/8” from the floor . Making sure the bracket is level, mark the mounting locations onto the structure.
-
Drill necessary holes into mounting surface and secure Mounting Bracket to surface using appropriate hardware, being sure to torque to manufacturer’s specifications. NOTE : Mounting hardware not included. Ensure the mounting surface (wall, etc.) and mounting hardware can safely hold a minimum ver tical load of 150 lbs.
-
Install empty tank onto Mounting Bracket (if wall mounting) or table top surface.
-
Remove Fill Cap and fill tank to line with potable water (approximately 9 gallons). Failure to use potable water can result in emergency units producing impure or contaminated water , possible causing further injury .
IMPORTANT
Self-contained eyewash equipment shall be visually checked frequently to deter mine if flushing fluid needs to be changed or supplemented. Frequency of these inspections is dependent on environment conditions, but at a minimum weekly . Failure to
conduct visual checks could lead to fur ther injury .
Customer shall take precautions to help prevent the growth of potentially harmful bacteria in eyewash tanks. Either of the following procedures is recommended.
Thor oughly cleanse tank at least once every month. See “Maintenance” Section for further information of cleaning unit.
Procedure 1: Use suitable Bacteriostatic preser vative to help prevent growth of bacteria in eyewash tank. Eyewash tank should be drained, flushed and refilled with clean potable water and Bacteriostatic preser vative added as directed by the preser vative’ s manufacturer .
Procedure 2: Drain, flush and refill units with clean potable water at least once every week unless site conditions require more frequent changing. -
Reinstall Fill Cap and secure it with the tamper -evident Seal T ie. Secure the included Maintenance T ag to the tank in a location where it can be easily checked.
SE-4400 REPAIR PARTS
| ITEM NO . | PART NO . | DESCRIPTION |
|---|---|---|
| 1 | RPG07-0021 | REPLACEMENT FILL CAP – QTY: 1 |
| 2 | RP G 38-0434 | REPLACEMENT SPRAY OUTLET – QTY: 1 |
| 3 | RP G 05-0935 | TAMPER EVIDENT SEAL TIE – QTY: 6 |
ACTIV A TION
T o activate the flow of water , rotate activation tray downward.
FLOW DAT A:
Run Time (Full Tank): 15 minutes (minimum)
Flow Rate: .4 gpm (1.5 L/min) (minimum)
SE-4400 ROUGH IN DIAGRAM
NEED HELP?
For additional assistance or ser vice please contact:
SPEAKMAN®
400 Anchor Mill Road
New Castle, DE 19720
800-537-2107
customerservice@speakman.com
www.speakman.com
92-SE-4400-04
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>