XGP X10 Helmet Bluetooth Headset User Guide
- June 1, 2024
- XGP
Table of Contents
XGP X10 Helmet Bluetooth Headset User Guide
Tips:
- To ensure the sound quality and normal audio output, please plug the speaker wire into the TYPE-C jack all the way till there is a “click” tone.
- Due to the wzaterproof finish for the charging connector, the Type-C Jack will be much longer, so please use our TYPE-C cable for charging
Product Overview
Basic Function
Power on
Power off
Battery Prompts
Low Battery Prompt
(Please use the DC 5V adapter to charge. It will flash RED light while charging and turn BLUE when fully charged.)
Factory Reset
(After factory reset, power off and restart the device. The power button will flash red and blue alternately. At this point, you can directly connect the device to your phone via Bluetooth without entering pairing mode again;
Phone Call
Connect Phone (Power off status)
Answer call
End call
Reject call
Enable Auto-answering call
Disable Auto-answering call
(The factory default setting is “No auto answering”）
Activate Voice Call (Siri/Google Assistant)
Universal Pairing
2-Way Bluetooth Intercom (Power on Status)
(To connect with XGP other styles intercom, just enter the pairing mode together when the red and blue light flash on both units, wait till the blue light slowly flashes then you can talk back and forth.)
Music Function
Music Play/Pause
Music Switch
Volume Modulation
- There’s a tone “du” while adjusting volume. When the volume is at themaximum the tone turns to “di”, and at the minimum it turns to “du”
- The X10 has Audio Multitasking feature. So when have a intercom talk and music playing simultaneously, rotate the Jog Dial directly to adjust the music volume, and pause the music playing then rotate the Jog Dial to adjust the intercom volume.）
Mesh Intercom Function
Mesh Intercom Function (Power on Status)
Exit Mesh Intercom
Recover Mesh Intercom
Turn off Mesh Intercom
- The XGP X10 can support up to 10 people to have a mesh intercom talk. The “N”presents numbers 1 to 10.
- Anyone who want to exit the mesh intercom, just click the “M” button, at this time others can still keep connected and talk; if he wanna re-enter the mesh intercom talk, click the “M” button again to join in.
- If someone beyond the range and disconnect from the mesh intercom talk, it will automatically reconnected if he come back to the mesh group talk within 5 minutes, or have to click the “M” button again to re-join in.
FCC & ISED Statement
This device complies with Part 15 of the FCC Rules and with Industry Canada licence-exempt RSS standard(s).Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonableprotection against harmful interference in a residential installation. This equipment generates,uses and can radiate radio frequency energy and, if not installed and used in accordance withthe instructions, may cause harmful interference to radio communications. However, there is noguarantee that interference will not occur in a particular installation. If this equipment doescause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one ormore of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS 102 RF exposure, users can obtain Canadian information on RF exposure and compliance.
This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment.
Radiation Exposure Statement for camera
This equipment should be installed and operated with minimum distance 0cm
between the radiator & your body.
Email: XGPTX2023@163.com
youtube @XGPTX
Ins @xgpmoto
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>