Aeolus GV01 Professional Steam Generator Instruction Manual

: June 1, 2024
: AEOLUS

Aeolus GV01 Professional Steam Generator

Aeolus-GV01-Professional-Steam-Generator-fig-1

Specifications

Power Supply: 220 – 240 Volts, 50/60 Hz
Professional Iron Power: 850W
Steam Brush or Agile Iron Power: 350W
Boiler Heating Element Power (watt):
- GV01, GV02, GV04, AV02, GVS1, GVS2: 900W
- GV03, GV05, AV03: 1300W
- GV06: 1300W + 900W
Operating Pressure: 2.8 bar (4.8 bar in GV05 model)
Weight:
- GV01, GV02, GV03, GV04, GV05, GV06: 1.5kg – 2.4kg – 3.5kg – 2kg – 2.4kg – 5kg
- AV02, AV03, GVS1, GVS2: 6kg – 6.8kg – 8kg – 6.2kg – 7.2kg – 10kg
- AV02: 8kg – 16.5kg – 5.5kg – 5kg

Product Usage Instructions

Steam Generating Systems

Ensure the device is plugged in and properly connected to a power source.
Turn on the general switch for the iron, brush, or steam lance as needed.

Cleaning Systems
Follow the specific instructions for using the steam generator with cleaning accessories.
Important: Do not leave the appliance unattended even in temporary absence.

Lubricating O-Rings\
All steam generators with steam plug and socket feature O-rings. To prevent O-ring breakage and steam leakage from the plug, lubricate the O-rings based on usage or at least once a month.
Note: All repair and replacement operations must be carried out by an authorized technical service center.

FAQ

The indicator light does not turn on when switching the iron on.

Cause: Broken switch, improperly inserted power cord, lack of electrical power.
Solution: Check that the power cord is correctly plugged into the power outlet or contact Technical Assistance if the issue persists.

SWITCHES

Aeolus-GV01-Professional-Steam-Generator-fig-3

ACCESSORIES

Aeolus-GV01-Professional-Steam-Generator-fig-5

INTRODUCTION

Congratulations on choosing the quality and reliability of AEOLUS prod-ucts. The Professional Steam Generator of AEOLUS Home & Professional are built according to innovative technical principles and pass a double operation and quality check at the end of assembly.
The copper boiler with external antiscale heating element has the advan-tage of not wear out, to reduce the waiting times for the production of steam, with consequent energy saving, and to increase the duration of the production of steam.
The efficiency of the steam generator is guaranteed by the best compo-nents and operating tools on the market.

BEFORE USING THE MACHINE

CAREFULLY READ THE INSTRUCTION MANUAL

GENERAL SAFETY INSTRUCTIONS

Keep carefully this instruction manual for future reference; this instruction man-ual should be read and understood by all who will use the equipment.
After unpacking, check the integrity of the appliance; in case of doubt do not use the appliance and contact the Technical Assistance Service.
All packaging materials (plastic bags, polystyrene, etc..) should be kept out of reach of children as potential sources of danger.
Before connecting the device ensures that the data label correspond to those of the electrical grid; the label is located next to the switches.
Check that the electrical capacity of the system and outlets are suitable to the maximum power of the appliance indicated on the label; in case of doubt ask to a professional qualified technician.
It is forbidden the use of or multiple adapters and extensions also if they comply with current safety standards.
This equipment must be used only to uses for which it was built, any other use is considered improper and therefore dangerous.
The manufacturer cannot be held responsible for any damage caused by improp-er, incorrect or unreasonable use of the device.
The use of any electrical device requires the observance of some basic rules. In particular: do not touch the appliance with wet/damp hands or feet; do not use the unit with bare feet; do not pull the cord or the appliance to remove the plug from the socket; do not expose the unit to the atmospheric agents (rain, sun, etc.); do not allow the appliance to be used by children, incapable or infirm per-sons without supervision. It is normal that during the first minutes of use, the iron and the boiler release light vapors and odors, due to the presence of natural oils used during assembly.
Before performing any maintenance / cleaning, turn off and unplug the appliance from the power supply by removing the appliance from the socket.
In case of failure and/or malfunction of the device, turn it off and do not tampered it (see PROBLEMS RESOLUTIONS); for possible repairs, just ask the Authorized Aeolus Assistance Centre and requires the use of original spare parts (non-com-pliance with the written above may affect safety of the appliance). Contact the AEOLUS Assistance Service to know the nearer Technical Assistance Centre.

IMPORTANT

Never unscrew the safety valve cap during use.
Do not fill the boiler without having removed the plug from the socket.
Do not remove safety device and protective cover.
Do not block the air openings and always check that are free and never even par-tially obstructed.
Do not use the device in the immediate vicinity of bathtubs, showers, sinks, swim-ming pools and make sure that the switch or other controls can not be achieved by the person who is using the bathroom, shower, sink…
Do not use the unit immediately below a socket outlet.
Do not use the device in the presence of flammable liquids or substances such as alcohol, insecticides, gasoline, etc. or near curtains.
The device is constructed in a workmanlike manner. Its electrical and mechanical durability and reliability will be more efficient if it is used properly and if it will be done a regular maintenance.

DISPOSAL

The appliance, which has to be treats separately from the domestic refusals, must be given to a centre of diversi-fied waste collection facilities for electric and electronics equipments or redelivered to the retailer during the pur-chase of a new equipment. The consumer is responsible of the conferment of the appliance at end life to appropriate waste collection facilities and it is necessary to follow the provisions in force under penalty of the penalties provided for by current legislation on the subject.

TECHNICAL DATA

Power supply	220 – 240 Volts, 50/60 Hz
Power of professional iron	850W
Power of professional steam brush or Agile iron	350W

Power of heating heating system (watt)
GV01, GV02, GV04, AV02, GVS1, GVS2| 900
GV03, 05 e AV03| 1300
GV06| 1300+900
Working pressure (bar)| 2,8 (4,8 on GV05 model)
Boiler capacity (litres)
GV01, GV02, GV03, GV04, GV05, GV06| 1,5 – 2,4 – 3,5 – 2 – 2,4 – 5
AV02, AV03, GVS1, GVS2| 2 – 3,5 – 1,2 – 1,2
Weight (kg)
GV01, GV02, GV03, GV04, GV05, GV06| 6 – 6,8 – 8 – 6,2 – 7,2 – 10
AV02 – AV03 – GVS1 – GVS2| 8 – 16,5 – 5,5 – 5

IMPORTANT: as with all professional steam generators, to iron or clean with DRY STEAM, introduce water up to a maximum of 80% of the boiler capacity so that the steam chamber can be formed.

LEGEND

Aeolus-GV01-Professional-Steam-Generator-fig-2

Data plate and label warning
Cord holder
Safety cap
General Switch iron, brush, steam gun
Boiler switch
Pressure gauge
Steam ready indicator
Draining faucet
Steam switch
Steam flow adjustment knob
Soleplate temperature adjustement
End water indicator
Outlet for quick collection GV05 / GV06
Iron rest mat
Stain remover pistol
Cleaning accessoires
- 16a Steam handle hose
- 16b Steam lance
- 16c PVC brush nozzle
- 16d Steam brush connector
- 16e Steam extensions tube
- 16f Steam rectangular brush
- 16g Steam window cleaner
- 16h Steam triangular brush

A Power plug accessory for AV02
B Power plug accessory for AV03, GV06
C Power plug accessory for GV05

HOW TO FILL THE BOILER

Before starting to iron/clean, be sure of the presence of the water in the boiler. In case you need to fill the boiler, make sure the appliance is unplugged and add water when the boiler has cooled down. When the boiler is cold, remove the safety cap 3 with caution and with the aid of a funnel, add tap water. Do NOT completely fill the boiler, since drops of water could come out from the iron together with the steam (fill max. 80% of boiler volume). Fill the boiler according to the workload (1 litre of water enable you to iron for about 1 hour). For small workloads, it is advisable to add less warm tap water: the boiler will be ready in less time with a corresponding saving of electric energy.
It is not necessary to use demineralized water. Be careful not to let out the water from the entrance and close the cap without tightening strongly (tightening with only “three fingers”).

SETTING UP AND USE

OPERATING INSTRUCTIONS FOR IRONING SYSTEMS WITH IRON/BRUSH

Plug the power cable to the power socket.
Turn on general/iron-brush switch 4 and boiler switch 5. For ironing without steam turn on only switch 4 (in model GV06 there are n. 2 boiler switches). Set the tem-perature knob 11 of the iron/brush on the desired temperature. The temperature regulation is approximate. Test the temperature on a hidden part of the garment to be ironed. The adjustment for the steam iron/brush is indicated by the symbol “..” or higher.
With high temperatures you run the risk of burning the garment or obtaining an undesired shine effect. The use of anti-shine Teflon shoe will eliminate this. Before starting to iron, wait until the steam ready indicator 7 lights up and/or the pressure gauge 6 reaches 2/3 atmospheres. During ironing, the steam ready indicator will go on and off, depending on the pressure inside the boiler. To get the steam press the red switch 9 on the handle of the steam iron/brush. The first time point the steam jet away from the garment, in a safe direction and press more times the red switch to eliminate any condensate from the iron. Act on the knob 10 to adjust the steam jet (clockwise to increase the jet). When finished ironing, turn off all switches. It is not necessary to empty the residual water from the boiler. When the end water indicator 12 turns on (only in the models GV02 and GV05), the water in the boiler is over. Press the steam switch 9 to release the pressure inside the boiler. Turn off all switches. Open with caution the safety cap to release all residual pressure. Wait 5 minutes for the boiler to be cold and fill it following the instruction, if you want to iron again (ADVICE: with warm water the boiler will be under pressure in less time).

OPERATING INSTRUCTIONS FOR STEAM GENERATORS WITH CLEANING ACCESSOIRES

Insert the Power plug C of the steam handle 16a into the outlet 13. Depending on the surface to be treated, insert the correct accessory in the steam connector. Insert the power plug into an electrical socket. Activate the main switch 4 and the boiler switch 5.
Wait until the steam ready light 7 is on and/or the pressure gauge 6 reach 4.5 bar. Adjust the steam flow using the knob 10. To dispense steam, press the steam han-dle button 9 on the steam handle 16a. The steam allows to clean and sanitize surfaces and objects; the supplied accessories as specified in the legend allow multiple applications. In case of delicate surfaces, we recommend the use of a microfibre cloth (such as AR064 PM on page 4) to be applied to the accessory code 16f or 16h (see page 2). Using the microfibre cloth also allows you to quick-ly absorb the dirt dissolved in the steam. At the end of the work, turn off all the switches and disconnect the power cord from the electrical socket.
DO NOT UNSCREW THE CAP WHEN THE BOILER
IS UNDER PRESSURE / IN USE.
DO NOT LEAVE THE APPLIANCE UNATTENDED,
EVEN IN THE EVENT OF A TEMPORARY ABSENCE.

MAINTENANCE

CLEANING OF THE BOILER

Before emptying the water from the boiler, unplug the machine from the power supply and unscrew the safety cap 3 half a turn to release the pressure and heat inside the boiler. When the boiler is cold, it is possible to over-turn with caution allowing the water outlet (see Figures). In models GV03, GV06 and AV03 there is a draining fau-cet in the lower part for emptying the boiler (turn the the draining faucet of 90° anticlockwise).
To clean the boiler, pour a glass of white vinegar with a glass of water in the boiler. Wait 2/3 minutes. Empty the solution. Pour in the boiler 1 litre of tap water to remove the smell of vinegar. Empty again. The cleaning operation must be done according to the use of the machine but at least 1 time per month (or every 30 hours of use).

O-RING LUBRICATION
All steam generators with steam plug and socket have O-rings. In order to be able to easily insert the plug into the socket and not risk breaking the O-rings with steam coming out of the plug, the O-rings must be lubricated at least once per month or depending on usage.
ALL REPAIR AND / OR REPLACEMENT OPERATIONS MUST BE DONE BY AN UTHORIZED TECHNICAL ASSISTANCE CENTER

TROUBLESHOOTING GUIDE

FAULT	CAUSE	SOLUTION
Putting the iron switch on position “ON” , the lamp does not light up.	Switch
broken, power cable not properly inserted, lack of power supply.	Check that

the power ca- ble is plugged in the power socket or contact the Tech- nical Assistance Centre if the problem persists.
After some minutes from switching on, the iron is still cold.| Thermostat is wrongly set.| Adjust the thermostat knob to a higher temperature or contact the Technical Assis- tance Centre if the problem persists.
The temperature of the iron is too high.| The thermostat is faulty or is set to a too high temper- ature.| Adjust it or contact the Technical Assistance Centre if the problem persists.
Water or too wet steam come out from the iron.| The thermostat tempera- ture is too low or too much water has been introduced into the boiler| Introduce less water or con- tact Technical Assistance if the problem persists.
The steam getting out from the iron is too dry.| The thermostat is faulty or is set to a too high temper- ature.| Decrease the temperature of the iron by acting on the thermostat or contact the- Technical Assistance Centre if the problem persists.
Pressing the steam switch, steam does not come out.| Coil is burned, switch bro- ken, iron power cable is damaged.| Contact the Technical Assis-

tance Centre.

Turning on the boiler switch, after about 15 minutes the steam ready lamp does not light up.| Heating element has blown, lack of water in the boil- er, pressure switch broken, steam ready lamp burned out.| Contact the Technical Assis-

tance Centre.

While working, the steam start missing.| Lack of water in the boiler.| Read HOW TO FILL THE

BOILER and add water in the boiler.

EN WARRANTY CERTIFICATE

To be kept with the product

The guarantee is valid for 5 years. Present the guarantee certificate and the invoice with the product at the action of the request of reparation. From the guarantee are excluded the defects, the damages and the breakdowns that might occur for an incorrect and improper use by the customer, for missed respect of the warnings and conditions of use indicated in this instructions book, for a not correct installa-tion or maintenance, for interventions effected by not authorized personnel. In the aforesaid period of warranty the manufacturer undertakes, after having effected the appropriate technical evaluations, to fix or to replace for free, the parts of the appliance that result to have manufacturing defects. From the warranty are ex-cluded the electric parts, the painted or enamelled parts, the knobs, the handles, the plastic mobile or removable parts, the lamps, the glass parts, the hoses, the external electric wire and all possible accessories of normal usury.
The manufacturing society is not responsible of the direct or indirect damages caused to people or things from breakdown of the appliance or consequent to the forced suspension of the use. The interventions under warranty will be directly performed by an Authorized Technical Assistance Centre as long as the appliance must be directly transported or sent at the expense of the client. Contact the man-ufacturer to know the closer Authorized Technical
Assistance Centre. The perfor-mance effected under warranty does not prolong the period of the same warranty. The rights of guarantee respond to the D.lgs. 24/2002.