AIPHONE AI-SSV Vandal Resistant Sub Station Instructions

AIPHONE AI-SSV Vandal Resistant Sub Station

Product Information:

functions as a limited stop button.
Wiring to AI-900RS via supplied connector| Orange wire connects to A (top) terminal, Brown wire connects
to B (middle) terminal, and Black wire connects to C (bottom)
terminal.
Yellow BNC connector for video output| A yellow BNC connector used for video output.
Speaker| A water-proof and puncture-resistant speaker with a resistance
of 625 ohms, power of 1W/25V, diameter of 2 inches, and a magnet
weight of 2.4 oz.

Specifications

set in
the system programming.
Communication| The sub station allows hands-free communication. The master
station is push-to-talk, release-to-listen, or VOX via
handset.
Video Output| Provides a 75 Ohm / 1Vp-p composite video output.
Iris Control| Automatic iris control.
Minimum Illumination| 1.0 lux
Effective Picture Element| 512×492 NTSC
Lens Mount| 3.7mm Cone Pinhole Lens
Camera Power Source| 12V DC, 100mA (via included power supply)
MTBF| Mean Time Before Failure: 80,000 Hours
Faceplate| 12 gauge stainless steel
Mounting| Tamper-proof screws included (6×32 for use with flush 2-gang
box) with T-10 TORX bit. When using SBX-2G, use the hardware
included with that unit.
Terminations| Color-coded pre-wired pigtails. Orange, Brown, and Black wires
connect to AI-900RS connector. Red connector for 12V DC power.
Yellow connector for 75 Ohm / 1Vp-p video output (BNC).
Audio Wiring| 2 conductors with overall shield. Use Aiphone #822202
wire.
Audio Wiring Distance| 1650′ (24AWG); 2650′ (22AWG)
Video Wiring| An independent BNC connection is required from the sub station
pigtail to the destination video device.
Dimensions (H x W x D)| AI-SSV alone: 4-11/16 x 4-11/16 x 2
With SBX-2G: 4-3/4 x 4-7/8 x 3-5/8 (Top) 2-3/8 (Bottom)

Product Usage Instructions:

1. Connect the orange wire to the A (top) terminal of the AI-900RS connector.
2. Connect the brown wire to the B (middle) terminal of the AI-900RS connector.
3. Connect the black wire to the C (bottom) terminal of the AI-900RS connector.
4. Connect the yellow BNC connector to the video output device.
5. Ensure the speaker is connected properly and securely.
6. Supply power to the camera using the included 12V DC power supply.
7. Mount the AI-SSV using the tamper-proof screws and T-10 TORX bit.
8. If using SBX-2G, use the hardware included with that unit for mounting.
9. Connect the audio wiring using Aiphone #822202 wire.
10. Ensure the audio wiring distance does not exceed 1650′ (24AWG) or 2650′ (22AWG).
11. Connect the video wiring independently from the sub station pigtail to the destination video device.

Vandal Resistant Sub Station with built in Color pinhole camera for use with the Al-900 System

INSTRUCTIONS

The AI-SSV is a 2-gang stainless steel vandal proof and weather resistant sub station designed for use with the Al-900 system. It is constructed of 12 gauge stainless steel and has a stand alone camera built in. The unit either flush mounts into a 2-gang box, or surface mounts with the SBX-2G. Each unit includes a 12V DC power supply for the camera, tamper proof screws, and a tool for installation.

INSTALLATION

1. For flush mounting, install sub station in standard 2-gang electrical box with minimum 2-1/2″ depth.
2. For surface mounting, use the SBX-2G surface mount enclosure (sold separately).
3. Only the 12V DC power supply included should be used to power the Al-SSV camera.
4. IMPORTANT! These units are designed for use in normal weather conditions, and to allow drainage and evaporation of moisture that naturally gets into the unit. Do not apply caulking or silicone sealant around the unit when installing, and do not use weather stripping around the perimeter of the box when mounting. If sealing the unit is required, the bottom must remain unsealed. Sealing the unit will prevent or inhibit moisture from dissipating from inside the unit, which may cause corrosion or deterioration of the internal components over time.

AI-SSV BACK VIEW & WIRING DIAGRAM

SPECIFICATIONS:

• Audio Power Source:
  Supplied by master station

• Speaker:
  625 ohms, 1W/25V, 2″ diameter, water proof and puncture resistant, 2.4 oz. magnet

• Call Button:
  SPST call button, momentary activation. Limited stop button

• Call Annunciation:
  Call tone rings at master for duration set in programming of system.

• Communication:
  Hands free at sub. Master is push-to-talk, release-to-listen, or VOX via handset.

• Video Output:
  75 Ohm / 1Vp-p composite video

• Iris Control:
  Auto

• Minimum Illumination:
  1.0 lux

• Effective Picture Element:
  512×492 NTSC

• Lens Mount
  3.7mm Cone Pinhole Lens

• Camera Power Source:
  12V DC, 100mA (via included power supply)

• MTBF:
  (Mean Time Before Failure) 80,000 Hours

• Faceplate:
  12 gauge stainless steel

• Mounting:

  • Flush mount into a 2-gang box (minimum 2-½ depth) or surface mount into SBX-2G (sold separately)
  • Tamper proof screws included (6×32 for use with flush 2-gang box) with T-10 TORX bit
  • When using SBX-2G, use the hardware included with that unit.

• Terminations:
  Color-coded pre-wired pigtails. Orange, Brown and Black wires connect to Al- 900RS connector.
  Red connector = 12V DC power; Yellow connector = 75 Ohm / 1Vp-p video output (BNC).

• Operating Temperature:
  14°F ~ 140°F (-10°C ~ 60°C)

• Audio Wiring:
  2 conductors w/overall shield. Use Aiphone #822202 wire.

• Audio Wiring Distance:
  1650′ (24AWG); 2650* (22AWG);

• Video Wiring:
  Independent BC connection from sub station pigtail to destination video device.
  Dimensions (H × W x D): AI-SSV alone: 4-11/16″ × 4-11/16″ × 2″
  With SBX-2G: 4-3/4″ × 4-7/8″ x 3-5/8″ (Top) 2-3/8″ (Bottom)

Aiphone Communication Systems
1700 130th Ave. N.E.
Bellevue, WA 98005
425-455-0510
FAX 425-455-0071

TOLL FREE TECHNICAL SUPPORT:
800-692-0200
TOLL FREE FAX LINE: 800-832-3765
E-MAIL: tech-serv@aiphone.com

References

• Manual-Hub.com – Free PDF manuals!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>