Aqara P2 Motion and Light Sensor Instruction Manual

: June 1, 2024
: Aqara

Table of Contents

Product Introduction
Quick Setup
Product Specifications
Warnings
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Motion and Light Sensor P2 User Manual

Product Introduction

Motion and Light Sensor P2 detects human motion and condition of ambient light. When detecting human movement or changes in ambient light conditions, Motion and Light Sensor P2 will send notice to the Aqara Home app through or link to other devices based on Thread.

A Matter-compatible Thread Border Router is required for use.

Aqara P2 Motion and Light Sensor -

Quick Setup

Please make sure you have a Matter-compatible app and a Matter-compatible Thread Border Router.
Remove the insulating tab. The indicator should start breathing.
Please note: If the indicator is not breathing, press and hold the reset button for 5 seconds until the LED indicator starts blinking and release it. The device will enter the pairing mode.
Open the Matter-compatible app and scan the Matter QR setup code on the manual or package, or enter the Matter numeric setup code printed on the product to add the device to the app.

Product Specifications

Motion and Light Sensor P2
Model: ML-S03E/ ML-S03D
Battery: CR2450 × 2
Wireless Protocols: Thread, Bluetooth 5.0
Bluetooth Operation Frequency: 2402-2480 MHz
Bluetooth Maximum Output Power ≤ 13 dBm
Thread Operation Frequency: 2405-2480 MHz
Thread Maximum Output Power ≤ 13 dBm
Dimensions: 33.1 × 33.1 × 41.6 mm (1.3 × 1.3 × 1.6 in.)
Operating Temperature: -10°C ~ 55°C (14°F ~ 131°F )
Operating Humidity: 0 ~ 95% RH, no condensation
What is in the Box
ML-S03E: Sensor Main Unit × 1, Holder × 1, Sticker × 2,
User Manual × 1
ML-S03D: Sensor Main Unit × 1, Holder × 2, Sticker × 4,
User Manual × 1
Manufacturer: Lumi United Technology Co., Ltd.
Address: Room 801-804, Building 1, Chongwen Park, Nanshan iPark, No. 3370, Liuxian Avenue, Fuguang Community, Taoyuan Residential District, Nanshan District, Shenzhen, China.
Online Customer Service: www.aqara.com/support
Email: support@aqara.com

For details, please see www.aqara.com/support or scan the QR code below to get the detailed electronic manual.

Aqara P2 Motion and Light Sensor - qr code https://prd.aqara.com/manual/?mid=manual.1064949965801345024

Warnings

This product is not a toy, please keep children away from this product.
This product is designed for indoor use only. Do NOT use in humid environments or outdoors.
Beware of moisture, do NOT spill water or other liquids onto the product.
Do not place this product near a heat source.
Do not attempt to repair the product by yourself. All repairs should be performed by authorized personnel.
This product is designed only for improving the convenience of household life, and for status notifications. If the user violates the product instructions and this warning, the manufacturer is not responsible for any risks and property losses caused thereby.

Caution

Risk of explosion if the battery is replaced by an incorrect type.
Dispose of used batteries according to the instructions.
Do not ingest battery, Chemical Burn Hazard.
This product contains two coin / button cell battery. If the coin / button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death.
Keep new and used batteries away from children.
If the battery compartment does not close securely, stop using the product and keep it away from children.
If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.
Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion.
Leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas.
A battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas.
The equipment is only suitable for mounting at heights ≤ 2 m.

EU Declaration of Conformity
Hereby, [Lumi United Technology Co., Ltd] declares that the radio equipment type [Motion and Light Sensor P2, ML-S03E/ ML-S03D]are is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://www.aqara.com/DoC/

WEEE Disposal and Recycling Information
All products bearing this symbol are waste electrical and electronic equipment (WEEE as in directive 2012/19/EU) which should not be mixed with unsorted household waste. Instead, you should protect human health and the environment by handing over your waste equipment to a designated collection point for the recycling of waste electrical and electronic equipment, appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. Please contact the installer or local authorities for more information about the location as well as terms and conditions of such collection points.
Symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic
Under normal use of condition, this equipment should be kept a separation distance of at least 20cm between the antenna and the body of the user.

FCC ID ：2AKIT-MLS03
Federal Communications Commission (FCC) compliance statement:

This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment of and on, the user is encouraged to try to correct the interference by one or more of the following measures:

—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit diﬀerent from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.

RF Exposure statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

IC:22635-MLS03
IC NOTICE TO CANADIAN USERS
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device.
This Class B digital apparatus complies with Canadian ICES ‐003.
This device complies with RSS‐247 of Industry Canada.
Operation is subject to the condition that this device does not cause harmful interference.
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Lumi United Technology Co., Ltd is under license. Other trademarks and trade names are those of their respective owners.