VOLLRATH 15084 Cutting Blade Assembly Installation Guide
- June 1, 2024
- VOLLRATH
Table of Contents
VOLLRATH 15084 Cutting Blade Assembly
Specifications
- Brand: Vollrath
- Model: Table Top Model / Wall Mount Model
- Material: Stainless Steel
- Blade Type: Sharp cutting blade assembly
- Dimensions: Varies based on model
Product Usage Instructions
Safety Precautions:
Blades are sharp and can cause cuts and amputation. Only trained personnel should operate the equipment.
Blade Maintenance:
Wash new blades with warm, soapy water to remove the protective oil film. Handle blades with caution to avoid injuries.
Assembly Instructions:
Tabletop Models:
- Remove the pusher head assembly by sliding it off the rod guides.
- Raise the bumpers approximately 2 inches.
- Loosen thumbscrew and carefully remove the blade assembly.
- Install the new cutting blade assembly and tighten the thumbscrew.
- Slide bumpers down guide rods to contact base assembly and position pusher head assembly onto the guide rods.
Wall Mount Models:
- Remove the pusher head assembly by following the specific instructions for wall mount models.
- Follow steps 2-5 mentioned above for tabletop models.
Maintenance:
Lubricate the guide bar with mineral oil or Petrol-Gel after each use to ensure smooth operation. Avoid using cooking oil as it may damage the equipment.
FAQ
Q: How often should I replace the cutting blade assembly?
A: It is recommended to replace the cutting blade assembly when it becomes dull or damaged to maintain optimal performance and safety.
Q: Can I use any type of oil for lubricating the guide bar?
A: No, it is recommended to use mineral oil or Petrol-Gel for lubrication. Avoid using cooking oil as it can cause damage to the equipment.
WARNING
Sharp Blade Hazard
Blades are sharp and can cause cuts and amputation.
To avoid injury from sharp blades, handle with caution. Only trained personal
should operate equipment or preform maintenance.
Wash new blades with warm, soapy water and rinse thoroughly to remove the thin protective oil film. Keep the sharp edge away from you when handling blades.
-
Remove the pusher head assembly:
Tabletop models: Slide the pusher head off the rod guides.
Wall mount models: Remove the locking pin (J). Lift handle and slide the pusher head off the guide rods. Place pin back into the hole on the handle assembly to prevent loss. -
Raise the bumpers approximately 2” (5.0 cm).
-
Loosen thumbscrew and carefully remove the blade assembly. Remove the cutting blade assembly by pressing upwards on the bottom of the side of the blade holder, where the thumbscrew is located. Discard the old blade assembly.
-
Install the new cutting blade assembly by inserting the tab on the blade holder into the groove in the base, then lowering the blade holder into the seated and flush position in the base. Tighten the thumbscrew.
-
Slide bumpers down guide rods to contact base assembly. Position pusher head assembly onto the guide rods, slowly lower pusher head assembly, and check pusher head block to blade alignment.
-
Lubricate the guide bar with mineral oil or Petrol-Gel after each use. Do not use cooking oil as it will become sticky and may permanently damage the equipment.
Assembly
-
A Guide Rods. Guides and align the pusher head onto the blade set.
-
B Handle. Used to lower and raise the pusher head block
-
C Guides. Used for smooth and consistent operation of pusher head on the guide rods
-
D Pusher Head Assembly. Made up of the pusher head block (and “T” handle for tabletop models).
-
E Bumpers. Cushions the stop of the pusher head.
-
F Thumbscrew. Used to secure the pusher head block or the blade assembly.
-
G Pusher Head Bock. Pushes the food product through the blade set.
Specifically sized to match the corresponding blade assembly. -
H Blade Assembly. Houses the blades. Specifically sized to match the corresponding pusher head block
-
I Base Assembly. Holds the guide rods and blade assembly.
-
J Locking Pin. Secures the pusher head to the handle.
The Vollrath Company, L.L.C.
1236 North 18th Street
Sheboygan, WI 53081-3201 U.S.A. Main Tel: 800.624.2051 or 920.457.4851 Main
Fax: 800.752.5620 or 920.459.6573 Customer Service: 800.628.0830 Canada
Customer Service: 800.695.8560
Technical Services
techservicereps@vollrathco.com
Induction Products: 800.825.6036 Countertop Warming Products: 800.354.1970 All
Other Products: 800.628.0832
© 2016 The Vollrath Company L.L.C.\
Part No. 2350079-1 en 1/22/16
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>