ZEEVA ET-0851A RC Shooting Vehicle Instruction Manual

ZEEVA ET-0851A RC Shooting Vehicle

Product Information

Specifications

• Power supply: Double Shot Dual Function
• Shooting Vehicle: 5 (Five) AA 1.5V Alkaline Batteries (Not Included)
• Remote Controller : 2 (Two) AA 1.5V Alkaline Batteries (Not Included)
• Frequency: 2.4 GHz

Product Usage Instructions

Remote Control Vehicle Operation
To operate the Remote Control Vehicle, follow these steps:

• Forward: Push the up arrow on the control pad to move the vehicle forward.
• Backward: Push the down arrow on the control pad to move the vehicle backward.
• Turn Left / Right: Push the left or right arrow on the control pad to turn the vehicle in the respective direction.
• Lever Up / Down Front Wheels: Use the lever up/down button to adjust the front wheels of the vehicle.

Dart Blaster Mode
For using the Dart Blaster mode:

• Press the bullet fired button to shoot darts.
• Short press for single shots, long press for continuous shooting.

Water Blaster Mode
For using the Water Blaster mode:

• Press the bullet fired button to shoot water droplets.
• Short press for single shots, long press for continuous shooting.

Power On/Off
To power on/off the Remote Control Vehicle:

• Slide the ON/OFF switch to ON to turn on the vehicle.
• Slide the ON/OFF switch to OFF to turn off the vehicle.

Batteries Installation
Follow these steps for battery installation:

For Remote Control Vehicle

1. Unscrew the battery box cover.
2. Insert 5 x AA 1.5V batteries into the battery box following the correct polarity.
3. Replace the battery box cover and tighten the screw.

For Remote Controller

1. Unscrew the battery box cover.
2. Insert 2 x AA 1.5V batteries into the battery box following the correct polarity.
3. Replace the battery box cover and tighten the screw.

Note: Remove batteries if the product is not being used to prevent damage.

FAQ

• Q: How do I switch between Dart Blaster and Water Blaster modes?
  A: To switch modes, simply press the corresponding buttons on the remote control.

• Q: What should I do if the Remote Control Vehicle loses connection?
  A: Check the batteries in both the vehicle and the remote control. Ensure they are properly installed and have sufficient power.

ET-0851 REMOTE CONTROL DOUBLE SHOT DUAL FUNCTION SHOOTING VEHICLE INSTRUCTION MANUAL
Size : 560 x 110 mm

Instruction Manual
Thank you for purchasing the
Remote Control Double Shot dual Function Shooting Vehicle. This manual provides more information about this RC Vehicle, please read the instructions before using.
WARNING: DO NOT AIM AT EYES OR FACE.

Product Overview

Package Contents

INCLUDES:

•  (One) RC Double Shot Dual Function Shooting Vehicle 8.38in. x 9.45in. x 6.1in. (21.3cm x 24cm x 15.5cm). SOME ASSEMBLY REQUIRED.
• (One) Remote Controller 5.24in. x 3.58in. x 2.08in. (13.3cm x 9.1cm x 5.3cm)
• (One) Water Dropper 1.77in. x 3.74in. x 1.14in. (4.5cm x 9.5cm x 2.9cm)
• (One) Instruction Manual 24 (Twenty Four) Suction Darts
• 0.43in. x 1.97in. x 0.43in. each (1.1cm x 5cm x 1.1cm each)

Specifications

• Power supply:
• Double Shot Dual Function Shooting Vehicle:
  • 5 (Five) AA 1.5V Alkaline Batteries (Not Included). Remote Controller:
  • 2 (Two) AA 1.5V Alkaline Batteries (Not Included).
• Frequency: 2.4 GHz

Remote Controller

Standard Control

• Push the up arrow on control pad to move vehicle forward

• Push the left or right arrow on control pad to move vehicle turn in left or right direction
• Press the lever up button to make the Remote Control Vehicle front wheels lever up.
• Press the lever down button to make the Remote Control Vehicle front wheels lever down.
• Short press the bullet fired button to shoot, long press the button for continuous shooting.
• Short press the bullet fired button to shoot, long press the button for continuous shooting.

Power On/Off

• Remote Control Vehicle:
• Power On / Off Switch
• Slide the ON/OFF Switch to ON to turn on the
• Remote Control Vehicle.
• Slide the ON/OFF Switch to OFF to turn off the
• Remote Control Vehicle.
• Remote Controller:
  • The Remote Controller will be turned on automatically when the batteries have installed.
  • Remove batteries if product is not being used.

Batteries Installation

For Remote Control Vehicle

• To install batteries into the Remote Control Vehicle, unscrew the screw on the battery box cover to open the cover. Insert 5 x AA 1.5V batteries (Not Included) into the battery box. Batteries should be placed as shown on the diagram. Replace battery box cover and tighten the screw.
• For Remote Controller

• To install batteries into the Remote Controller, unscrew the screw on the battery box cover to open the cover. Insert 2 x AA 1.5V batteries (Not Included) into the battery box. Batteries should be placed as shown on diagram. Replace battery box cover and tighten the screw.
• (Notice: When inserting the batteries, you must insert according to the correct polarity, the Remote Control Vehicle and the Remote Controller won’t function if batteries are reversed.)

Dart Bullets Installation to the Blaster

1.  Put the ammunition clips into the machine.
2. Put the suction darts into the ammunition clips one by one, press the remote launch button to make the ammunition clips automatically enter (Please note the direction of the suction dart)
3. Connect the ammunition clips with suction darts together to form a circle.
4. When installing suction dart, load them to the end of the ammunition clip.

Dart Blaster Installation

• Put the convex point on the side of the battery into the card slot with “A” mark on the vehicle, and then turn clockwise to the end.
• To remove the blaster, turn anti-clockwise to the end.
• Repeat the above steps to replace the water blaster.

Dart Bullets Installation to the Blaster

1. Open the lid of the water blaster.
2. Remove the cap by turn anti-clockwise.
3. Use the water dropper to fill clean water into the blaster, replace the fitting and close it by turn clockwise.
4. Then close the lid.
   (Pay attention to not fill the bottle when adding water, and do not spill water on the body to prevent circuit board short circuit.)

Dart Blaster Installation

• Put the convex point on the side of the battery into the card slot with “A” mark on the vehicle, and then turn clockwise to the end.
• To remove the blaster, turn anti-clockwise to the end.
• Repeat the above steps to replace the dart blaster.

Performance Tips

1. Do not drive the Remote Control Vehicle on grass, sand or go through water.
2. Do not drive the Remote Control Vehicle in windy or rainy weather.
3. Do not drive the Remote Control Vehicle into any sharp object.
4. Keep fingers, hair and loose clothing away from Remote Control Vehicle.

Care and Maintenance

• Always use dry and soft cloth to clean this product.
• Avoid this product from being exposed to sunlight or heat.
• Avoid immersing these toys in water, otherwise, the electronic parts may be damaged.
• Check the product regularly. If any damages are discovered, please stop using immediately, until it is completely repaired in good working condition.

IMPORTANT: BATTERY INFORMATION

For AA Batteries
WARNING: TO AVOID BATTERY LEAKAGE

1. Be sure to insert the batteries correctly, and always follow the toy/game and battery manufacturers’ instructions.
2. Do not mix old and new batteries or alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium) batteries.
3. Always remove weak or dead batteries from the product.
4. Remove the battery if the product is is left unused for a long period of time.

Warning

• This product is suitable for individuals with operating experience in remote toys or those aged 14 years old and above.
• Please do not put the product in your mouth to prevent choking hazards from small parts.
• Avoid inserting your fingers into available interspaces.
• Do not engage in rough play with the product, such as throwing, crashing or twisting it.
• Store smaller-sized product accessories in places that are out of reach of children to prevent accidents.
• Avoid placing batteries in areas with high temperatures or exposing them to heat.
• When young children are operating the product, it is essential to ensure that adults are guiding them and maintaining visual control of the toy for convenient control.
• When the product is not in use, please switch off the power supply and remove the batteries.
• Please note that we cannot be held responsible for any injuries, property damage, or loss resulting from incorrect operation during the assembly or use of this product.
• Cau tion: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the product.

FCC Statement

This device complies with the part 15 of the FCC rules.
Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Caution: changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with instructions may cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on.

• The user is encouraged to try to correct the interference by one or more of the following measures:
  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or experienced radio/ TV technician for help.

RF warning statement:
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

• FCC ID: 2ADM5-ET-0851A
• Distributed by 1616 Holdings, Inc.
• 701 Market Street, Suite 200
• Philadelphia, PA 19106
• Made In Shantou, China
• Keep All Relevant Information for Future Reference
• Item# ET-0851A

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>