Cobra CA-MICROOBD-00 Obd-II Hardwire Kit User Guide
- June 1, 2024
- Cobra
Table of Contents
Cobra CA-MICROOBD-00 Obd-II Hardwire Kit
INTRODUCTION
This Vehicle Hardwire Kit connects your Micro USB powered device directly to your on board diagnostic port (OBD II), freeing up your 12V accessory port and eliminating clutter on your dash board. This Hardwire Kit should work with any Micro USB powered device, but is designed and tested specifically for Micro USB powered Radar Detectors and Dash Cams from Cobra.
NOTE: OBD II port locations, fuse types, and interior designs vary greatly by vehicle. This guide is intended to outline basic steps for installation but the process may differ depending on your car’s make and model.
USING THE OBD II HARDWIRE KIT
- Connect one end of the micro USB cable to the dash cam and tuck the cables into your vehicle’s headliner for a clean install.
- Plug the other end of the hardwire kit into your vehicle’s OBDII port. You can generally find the OBDII port on the underside of the dashboard by the driver’s side door. If you have trouble locating the OBDII port, please consult your vehicle’s owner’s manual.
- Go to the camera’s setting menu. Enable Parking Mode to monitor for impacts to your vehicle. Enable Motion Detection to monitor for movement in front of the camera (please note, this may result in more files being created).
- Enable power using the included power supply box. A green light will appear when power is being delivered to the camera.
NOTE: When the battery voltage is lower than 11.9V (12V vehicle systems) or 23.9V (24V vehicle systems), the hardwire kit’s low voltage protection function will be activated. Power to the connected device will be cut off and only resume after the car has been started and the car battery is charged.
FCC STATEMENT:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
WARNING: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference
by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Cobra Electronics Corporation™ is a trademark of Cobra Electronics
Corporation, USA.
This device complies with RSS-310 of Industry Canada. Operation is subject to
the condition that this device does not cause harmful interference.
CAN ICES-3B/NMB-3B.
TRADEMARK ACKNOWLEDGMENT
Cobra, and the snake design, are proprietary trademarks of Cobra Electronics
Corporation, USA. Other trademarks and trade names are those of their
respective owners.
Cobra Electronics Corporation™ is a trademark of Cobra Electronics
Corporation, USA.
DISPOSAL OF ELECTRONICS EQUIPMENT: This product may contain hazardous
substances that could impact health and the environment if not disposed of
properly.
The crossed out wheeled bin symbol indicates that the product should not be
disposed of along with household waste. II should be handed over to an
applicable collection point for the recycling of electrical equipment. By
ensuring that this product is disposed of correctly you will help/prevent
potential negative impact on the environment.
If you need more information on the collection, reuse and recycling systems, please contact your local civic office or the shop where ii was originally purchased.
WARNING: This product contains chemicals know to the State of California to cause cancer and birth defects or other reproductive harm.
PRODUCT SERVICE AND SUPPORT
For any questions about operating or installing this new Cobra product, PLEASE CONTACT COBRA FIRST … do not return this product to the retail store. The contact information for Cobra will vary depending on the country in which you purchased and utilize the product. For the latest contact information, please go to www.cobra.com/support.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>