VOLLRATH T38946 Cafeteria Breath Guard Instruction Manual
- June 1, 2024
- VOLLRATH
Table of Contents
VOLLRATH T38946 Cafeteria Breath Guard
Specifications
- Product Name: Cafeteria Breath Guard
- Model: One Piece and Three Piece
- Manufacturer: Vollrath Company, L.L.C.
One Piece Breath Guard Installation
- Ensure the breath guard uprights (A) are securely attached to the studs (B) using cap nuts (C). Repeat for all four uprights.
- Install the breath guard support tube (D) between the uprights (A) and secure with cap nuts (C).
- Attach the one piece breath guard (E) to the uprights with screws (F) and cap nuts (C), repeating for all mounting locations.
- Secure the side breath protector (G) to the support tube (D) using cap nuts (C).
Three-Piece Breath Guard Installation:
- Attach the breath guard uprights (A) to the studs (B) with cap nuts (C). Repeat for all four uprights.
- Install the breath guard support tube (D) between the uprights (A) and secure with cap nuts (C).
- Secure the side breath guards (E) using screws (F) and cap nuts (C) for all mounting locations.
- Attach the side shield (G) to the support tube (D) using cap nuts (C).
- Connect the support bar and stud assembly (H) to the side breath guards (E).
- Fix the top breath guard (I) to the support bar and stud assembly (H) using cap nuts (C).
Frequently Asked Questions (FAQ):
Q: What should I do if I encounter cracks in the plastic during
installation?
A: If you notice cracks in the plastic parts during installation, stop
tightening immediately to prevent further damage. Contact Vollrath’s service
department for assistance.
Installation Instructions
One Piece cafeteria Breath Guard three Piece cafeteria Breath Guard
These instructions cover the installation of the one pice Cafeteria Breath Guard and the three piece Cafeteria Breath Guard.
One Piece Breath Guard installatiOn
Some units are shipped with a breath guard not installed. To install the
breath guard follow these steps:
NOTE :
Use caution when tightening the cap nuts. Overtightening may cause the plastic
to crack.
-
Install the breath guard uprights (A) to the studs (B) securing with cap nuts (C) as shown. See Figure 1. Repeat for all four uprights.
Figure 1. One Piece Breath Guard Installation
-
Install the breath guard support tube (D) between the uprights (A) securing with cap nuts (C) as shown. Repeat on the other side.
-
Install the one piece breath guard (E) securing with screws (F) and cap nuts (C) as shown. Repeat for all four mounting locations.
-
Install the side breath protector (G) to the support tube (D) securing with cap nuts (C) as shown. Repeat on the other side.
Three Piece Breath Guard Installation
Some units are shipped with a breath guard not installed. To install the
breath guard follow these steps:
NOTE:
Use caution when tightening the cap nuts. Overtightening may cause the plastic
to crack.
-
Install the breath guard uprights (A) to the studs (B) securing with cap nuts (C) as shown. See Figures 1 and 2. Repeat for all four uprights.
-
Install the breath guard support tube (D) between the uprights (A) securing with cap nuts (C) as shown. Repeat on the other side.
-
Install the side breath guards (E) securing with screws (F) and cap nuts (C) as shown. Repeat for all mounting locations.
-
Install the side shield (G) to the support tube (D) securing with cap nuts (C) as shown. Repeat on the other side.
-
Install the support bar and stud assembly (H) to the side breath guards (E).Repeat for all mounting locations.
-
Install the top breath guard (I) to the support bar and stud assembly (H) securing with cap nuts (C). Repeat for all mounting locations.
The Vollrath Company, L.L.C. 1236 North 18th Street Sheboygan, WI 53081-3201
U.S.A.
Main Tel: 800.628.0830 Service Tel: 800.628.0832 FAX: 800.752.5620
- Vollrath of Canada, Co.
- Tel: 800.695.8560
- FAX: 800.752.5620
- © 2010 The Vollrath Company, L.L.C.