BOSCH SMS6ZCW00X Dishwasher User Guide

BOSCH SMS6ZCW00X Dishwasher

Product Information

Specifications

• Model: SMS6ZCW00X
• Energy Consumption: Varies based on programme
• Water Consumption: Varies based on programme
• Capacity: Not specified

Product Usage Instructions

Setting up Home Connect

1. Install the Home Connect app on your mobile device and follow the instructions.
2. Scan the QR code with the Home Connect app.

Overview of Water Hardness Settings

Refer to the table in the instruction manual for selecting the appropriate water hardness setting.

Adding Special Salt

1. Unscrew the lid of the dispenser for special salt and remove it.
2. Fill the dispenser with water on initial start-up.
3. Add special salt to the dispenser before starting the program. Never add detergent.
4. Place the lid back on the dispenser and close it.

Adding Rinse Aid

1. Press the catch on the lid of the dispenser for rinse aid and lift it.
2. Add rinse aid up to the max mark.
3. Close the lid of the dispenser for rinse aid.

Programmes

Refer to the programme data in the manual for duration, energy consumption, and water usage information.

Adding Detergent

1. Add detergent to the dry detergent dispenser as per the recommended quantity.
2. Close the lid of the detergent dispenser securely.

How to Use Your Appliance

1. Load suitable tableware into the dishwasher after removing large food remnants.
2. Switch on the appliance.
3. Select the desired programme.
4. Start the programme.
5. Remove tableware at the end of the programme.
6. To cancel a programme, press and hold for approximately 4 seconds.

Cleaning Filters

After each wash, check and clean the filters to ensure optimal performance.

FAQ

Q: How often should I add special salt?

A: Add special salt to the dispenser only before starting a new programme to avoid damage to the appliance.

Setting up Home Connect

Tip: Connect your appliance to a mobile device. You can con-veniently change all settings using the Home Connect app.

1. Install the Home Connect app on your mobile device and fol-low the instructions.
2. Scan the QR code with the Home Connect app.

Overview of water hardness settings

You can find an overview of the water hardness values that can be selected here.
A table of country-specific units can be found in the instruction manual.

Setting the water softening system

1. Press ⁠ .
2. To open the basic settings, press
3. Setup 3 sec. for 3 seconds.
4. The display shows Hxx.
5. The display shows
6. Press Start repeatedly until the right water hardness has been set.
7. To save the settings, press Setup 3 sec. for 3 seconds.

Programmes

• The programme data has been meas-ured in the laboratory according to European standard EN 60436.
• The consumption figures depend on the programme and additional func-tion selected.
• The running time will change if the rinse aid system is switched off or rinse aid needs to be added.

PRODUCT OVERVIEW

How to use your appliance

1. Load the tableware.
   Only clean tableware that is suitable for dish-washers. Remove large remnants of food from the tableware. Check that the spray arms can rotate freely.

2. Add detergent.

3. Switch on the appliance ⁠.

4. Select the programme

5. Select the programme Start

6. Remove the tableware at the end of the programme.

7. To cancel the programme, press Reset 4 sec. for approx. 4 seconds.
   The programme is cancelled and ends after ap- prox. 1 minute.

Cleaning filters

1. After each wash check the filters for residue.
2. Turn the coarse filter anticlock-wise 1 and re-move the filter system 2⁠.
3. Pull down the microfilter to remove it.

4. Press the locking catches 1 to-gether and lift the coarse filter out 2⁠.

5. Clean the filter elements under running water.

6. Re-assemble the filter system.

7. Insert the filter system into the appliance and turn the coarse filter clockwise. Make sure that the arrow markings match up.

Cleaning spray arms

1. Unscrew the upper spray arm 1 and pull down to remove 2⁠.
2. Pull up the lower spray arm to remove.

3. Check the outlet nozzles on the spray arms for blockages under running water and remove any foreign bodies.

4. Insert the lower spray arm.
   The spray arm clicks into position.

5. Insert the upper spray arm and screw it firmly in place.

Clean wastewater pump

1. Disconnect the appliance from the power supply.

2. Remove the filter system.

3. Scoop out any water.

4. Prise off the pump cover using a spoon and grip it by the crosspiece.

5. Lift the pump cover inwards at an angle and remove.

6. Remove any remnants of food and foreign bodies in the area of the impeller.

7. Insert the pump cover 1 and press down 2⁠.
   The pump cover clicks into position.

8. Install the filter system.

Troubleshooting

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>