BOSCH SMI8ZCS00X Dishwasher User Guide

BOSCH SMI8ZCS00X Dishwasher

Specifications

• Product: Dishwasher
• Model: SMI8ZCS00X
• Water Hardness Settings:
  • Soft: 0 – 1.1 mmol/l (Setting value: 0 – 8)
  • Medium Soft: 1.2 – 1.4 mmol/l (Setting value: 9 – 10)
  • Medium: 1.5 – 1.8 mmol/l (Setting value: 11 – 12)
  • Medium Hard: 1.9 – 2.1 mmol/l (Setting value: 13 – 15)
  • Hard : 2.2 – 8.9 mmol/l (Setting value: 16 – 62)

Product Usage Instructions

Setting up Home Connect:

1. Install the Home Connect app on your mobile device.
2. Scan the QR code with the Home Connect app to connect your appliance.

Adding Special Salt:

1. Unscrew the lid of the special salt dispenser and remove it.
2. Fill the dispenser with special salt just before starting the program.
3. Place the lid back on the dispenser and close it.

Adding Rinse Aid:

1. Press the catch on the lid of the rinse aid dispenser to open it.
2. Add rinse aid up to the max mark.
3. Close the lid of the rinse aid dispenser until it clicks into position.

Setting the Water Softening System:

1. Open the basic settings by pressing the designated button for approximately 3 seconds.
2. Select Water Hardness on the display.
3. Adjust the water hardness setting using the controls.
4. Save the settings by pressing the save button for approximately 3 seconds.

Programmes:
Choose a suitable programme based on your needs and load size to start the dishwasher cycle.

Machine Care:
Run machine care programmes periodically to maintain optimal performance of your dishwasher.

Favourite Programme:
Create and save your preferred settings for quick access to your favorite programme.

Before using for the first time, read the instruction manual and the safety information it contains

Setting up Home Connect

Tip: Connect your appliance to a mobile device. You can conveniently change all settings using the Home Connect app.

1. Install the Home Connect app on your mobile device and follow the instructions.
2. Scan the QR code with the Home Connect app.

Overview of water hardness settings

You can find an overview of the water hardness values that can be selected here. A table of country-specific units can be found in the instruction manual.

Setting the water softening system

1. Press ⁠.
2. To open the basic settings, press for approx. 3 seconds.
3. Press repeatedly until the display shows “Water hardness”.
4. Press – or  + repeatedly until the right water hardness has been set.
5. To save the settings, press for approx. 3 seconds.

Programmes

The programme data has been measured in the laboratory according to European standard EN 60436. The consumption figures depend on the programme and additional function selected. The running time will change if the rinse aid system is switched off or rinse aid needs to be added.

Adding special salt
To avoid damage to the appliance, only add special salt to the dispenser for special salt just before the program starts.

1. Unscrew the lid of the dispenser for special salt and remove it.
2. On initial start-up: Fill the dispenser right up with water.
3. Add the special salt to the dispenser. The water in the dispenser is displaced and forced out. Never add detergent.
4. Place the lid back on the dispenser and turn to close.

Adding rinse aid

1. Press the catch on the lid of the dispenser for rinse aid 1 and lift 2 ⁠.
2. Add rinse aid up to the max mark.
3. Close the lid of the dispenser for rinse aid. a The lid clicks into position.

Adding detergent

1. Add the detergent to the dry detergent dispenser.
2. Close the lid of the detergent dispenser. a The lid clicks into position.

How to use your appliance

1. Load the tableware. Only clean tableware that is suitable for dishwashers. Remove large remnants of food from the tableware. Check that the spray arms can rotate freely.
2. Add detergent.
3. Switch on the appliance ⁠.
4. Select the programme.
5. Start the programme ⁠. Sart.
6. Remove the tableware at the end of the programme.
7. To cancel the programme, press for approx. Reset 4 seconds. The programme is cancelled and ends after approx. 1 minute.

Cleaning filters

1. After each wash check the filters for residue.
2. Turn the coarse filter anticlockwise 1 and 2 and remove the filter system ⁠
3. Pull down the microfilter to remove it.
4. Press the locking catches 1 together and lift the coarse filter out 2 ⁠.
5. Clean the filter elements under running water.
6. Re-assemble the filter system.
7. Insert the filter system into the appliance and turn the coarse filter clockwise. Make sure that the arrow markings match up.

Cleaning spray arms

1. Unscrew the upper spray arm 1 and pull down to remove 2⁠.
2. Pull up the lower spray arm to remove it.
3. Check the outlet nozzles on the spray arms for blockages under running water and remove any foreign bodies.
4. Insert the lower spray arm. The spray arm clicks into position.
5. Insert the upper spray arm and screw it firmly in place.

Clean wastewater pump

1. Disconnect the appliance from the power supply.
2. Remove the filter system.
3. Scoop out any water.
4. Prise off the pump cover using a spoon and grip it by the crosspiece.
5. Lift the pump cover inwards at an angle and remove it.
6. Remove any remnants of food and foreign bodies in the area of the impeller.
7. Insert the pump cover and 1 press 2 down ⁠. The pump cover clicks into position.
8. Install the filter system.

Troubleshooting

FAQ

Q: How do I know which water hardness setting to choose?
A: Refer to the table in the instruction manual for country-specific values or use a water hardness testing kit to determine the correct setting.

Q: Can I use regular salt instead of special salt?
A: No, only use special salt designated for dishwashers to avoid damage to the appliance.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>