Shenzhen USV Technology Co Ltd 2AY5D-Q6 3-IN-1 Wireless Charger User Manual
- June 1, 2024
- Shenzhen USV Technology Co Ltd
Table of Contents
Shenzhen USV Technology Co Ltd 2AY5D-Q6 3-IN-1 Wireless Charger
Product Function Introduction
- Applicable mobile phones: iPhone 12/13/14/15 series
- Wireless Earbuds: Airpods pro, Airpods 2/3[Wireless Version], Other Qi
- Wireless Earbuds watch: support Apple Watch 1-9 generation wireless charging
Matters Needing Attention
- Do not place the product in water or near the fire source, so as not to cause malfunction of the charging equipment and mobile phone.
- Do not drop the device from a high place to avoid damage to the device due to falling to the ground.
- If you need to clean the charger, make sure it is not connected to the power supply.
- Recommended to use a QC3.0/PD power adapter to power the product.
Specification
- Input voltage: 9V/2A,5V/3A
- Phone output: 10W/ 7.5W/ 5U
- Headphone output: 3W
- Watch output: 2.5W
- Frequency : Phone&Earphone:115-205KHz
- Watch:326.5KHz
- Receiving distance : 0-4mm
- Conversion rate : ≥80%
Package Include
- Magnetic Wireless charger x1
- Type-C quick charge cable x1
- User manual x1
LED Indicator Status Description
- Connected to power supply: blue light flashes 3 times and turns off after 30s
- Standby: light off
- Quick charging : blue light stays on for 60 seconds and then turns off
- Charging exception alert: blue light keeps flashing.
- Please place the center of the mobile phone at the center of the charging board to get a better charging experience;
- Do not put metal debris or magnetic cards on the charging board, which may cause metal hair, magnetic card damage, charger damage, or other abnormalities;
- If the receiving coil or the transmitting board is overheated and the charging stops during use, please remove the charging device, wait for it to cool down, and try charging again.
- Do not pull the power cord violently to avoid the power cord from breaking or falling off.
- Please do not disassemble the product or put it into fire or water to avoid short circuits and leakage.
- The standard temperature of wireless charger Ql is 130°F, but our product temperature is controlled within 130°F. The charger will cut off the current when it is abnormally hot. Please contact us if any damage occurs.
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference,
- This device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, under Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used under the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body.