Tuya S7-BT Outdoor Smart Access Control System User Manual
- June 1, 2024
- Tuya
Table of Contents
Tuya S7-BT Outdoor Smart Access Control System
Introduction
- The device is a single-door standalone access control with Wiegand input & output. It uses Atmel MCU assuring stable performance. The operation is very user-friendly, and the low-power circuit makes it a long service life.
- The device supports 1,000 users (990 common users + 10 visitor users).
- It supports multi-access modes in card access, PIN access, card + PIN access, or multi-card/PIN access.
Optional Version:
The device with Bluetooth-enabled. People can install the Bluetooth APP to
easily access the door with their smartphone. (APP operation can refer to APP
manual)
Features
- Waterproof, conform to IP66
- Vandal-resistant metal enclosure
- One relay, 1,000 users (990 common + 10 visitors)
- Can add any 4~6 digits PIN on Infrared Remote Control
- Card Type: 125Khz EM Card/13.56Mhz Mifare Card (optional)
- Wiegand 26 bits output, Wiegand 26/34bits input automatic identification
- Card block enrollment
- Tri-color LED status display
- Pulse mode, Toggle mode
- Low temperature resistance (-40°C)
Specifications
Carton Inventory
INSTALLATION
- Remove the back cover from the unit
- Drill 2 holes(A, C) on the wall for the screws and one hole for the cable
- Knock the supplied rubber bungs to the screw holes(A, C)
- Fix the back cover firmly on the wall with 4 flat-head screws
- Thread the cable through the cable hole(B)
- Attach the unit to the back cover
Wiring
Sound and Light Indication
Basic Configure
Enter and Exit Program Mode
Set Master Code
Connection Diagram
Common Power Supply
Attention:
Install a 1N4004 or equivalent diode is needed when using a common power
supply, or the keypad might be damaged. (1N4004 is included in the packing)
Access Control Power Supply
Programming
Programming will vary depending on access configuration. Follow the
instructions according to your access configuration.
Notes:
User ID number: Assign a user ID to the access card / PIN to track it.
- The Common User ID
- PIN/ Card user ID: 0 ~ 989
- Visitor User ID: 990 ~ 999
IMPORTANT:
User IDs do not have to be proceeded with any leading zeros. Recording of User
ID is critical. Modifications to the user require the User ID to be available.
-
Proximity Card:
Proximity Card: 125KHz EM card or 13.56MHz Mifare card -
PIN:
Can be any 4~6 digits except 8888 which is reserved. Press the PIN on the Infrared Remote Control.
Add Common Users
PIN/Card user ID: 0~989; PIN length: 4~6 digits except 8888
Tips for PIN Security (Only valid for 6 digits PIN):
For higher security we allow you to hide your correct PIN with other numbers
up to a max of 10 digits.
Example PIN: 123434
- You could use (123434) or ** (123434)
- (“*” can be any number from 0~9)
Add Visitor Users
(User ID number is 990~999; PIN length: 4~6 digits except 8888) There are 10
groups of Visitor PIN/cards available, the users can be specified up to 10
times of usage, after a certain number of times, i.e. 5 times, the PIN/card
becomes invalid automatically.
Change PIN Users(PIN length: 4~6 digits except 8888)
Delete Users
Set Relay Configuration
The relay configuration sets the behaviour of the output relay on activation.
Set Access Mode
For Multi-user access mode, the interval time of reading can not exceed 5
seconds, or else, the device will exit to standby automatically.
Set Strike-out Alarm
- The strike-out alarm will engage after 10 failed entry attempts (Factory is OFF).
- It can be set to deny access for 10 minutes after engaging or disengage only after entering a valid card/PIN or Master code/card.
Set Audible and Visual Response
WIEGAND MODE
Pass-through Mode
(The device Operates as a Wiegand Output Reader)
In this mode, the device supports a Wiegand 26-bit output so the Wiegand data
lines can be connected to any controller that supports a Wiegand 26-bit input,
and then the device will operate as a slave reader.
Wiring Diagram
Controller Mode
(The device Operates as a Controller)
- It supports Wiegand 26/34 bits input (Automatic Identification), so an external Wiegand device with 26/34 bits output can be connected to the Wiegand input terminals on the device. Either an EM card reader (125 KHz) or a Mifare card reader (13.56MHz) can be connected to the device.
- Cards are required to be added at the external reader, except where an external EM card Reader is used, in this case, cards can be added at either reader or controller.
Wiring Diagram
OTHERS
Users Operation & Reset to Factory Default
- Open the door: Read valid card user or input valid PIN user #
- Remove Alarm: Enter Master Code # or Master Card or valid card/PIN user
- To reset to factory default & Add Master Card: Power off, press the Exit Button, hold it and power on, there will be two beeps, then release the exit button, and the LED light will turn yellow, then read any 125KHz EM card/13.56MHz Mifare card, the LED will turn into red, means reset to factory default successfully. Of the card reading, it is the Master Card.
Remarks:
- If no Master Card is added, must press the Exit Button for at least 5 seconds before release. (this will make the previously registered Master Card invalid)
- Reset to factory default, the user’s information is still retained.
Master Card Usage
Documents / Resources
| Tuya
S7-BT Outdoor Smart Access Control
System
[pdf] User Manual
S7-BT Outdoor Smart Access Control System, S7-BT, Outdoor Smart Access Control
System, Smart Access Control System, Access Control System, Control System,
System
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>