VOLLRATH 38731W Cafeteria Breath Guard Instruction Manual

: June 1, 2024
: VOLLRATH

Table of Contents

VOLLRATH 38731W Cafeteria Breath Guard
Product Usage Instructions
Installation Instructions
- One Piece Breath Guard Installation
- Three Piece Breath Guard Installation
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

VOLLRATH 38731W Cafeteria Breath Guard

Specifications:

Product Name: Cafeteria Breath Guard
Model: One Piece & Three Piece
Manufacturer: Vollrath Company, L.L.C.
Item No.: 2350030-01 Rev 04/12

Product Usage Instructions

One Piece Breath Guard Installation:

Install the breath guard uprights (A) to the studs (B) securingwith cap nuts (C) as shown in Figure 1. Repeat for all fouruprights.

Three Piece Breath Guard Installation:

Install the breath guard uprights (A) to the studs (B) securing with cap nuts (C) as shown in Figures 1 and 2. Repeat for all four uprights.
Install the breath guard support tube (D) between the uprights (A) securing with cap nuts (C) as shown. Repeat on the other side.
Install the side breath guards (E) securing with screws (F) and cap nuts (C) as shown. Repeat for all mounting locations.
Install the side shield (G) to the support tube (D) securing with cap nuts (C) as shown. Repeat on the other side.
Install the support bar and stud assembly (H) to the side breath guards (E). Repeat for all mounting locations.
Install the top breath guard (I) to the support bar and stud assembly (H) securing with cap nuts (C). Repeat for all mounting locations.

FAQ:

Q: What should I do if I accidentally over-tighten the cap nuts?
A: If you accidentally over-tighten the cap nuts and notice cracking in the plastic, stop immediately to prevent further damage. Contact customer service for assistance on replacing the,damaged parts.

Q: Can I disassemble the breath guard for cleaning?
A: Yes, you can disassemble the breath guard following the installation steps in reverse order. Clean each component separately using mild soap and water, then dry thoroughly before reassembling.

Installation Instructions

One Piece Cafeteria Breath Guard
Three Piece Cafeteria Breath Guard

These instructions cover the installation of the one pice Cafeteria Breath Guard and the three piece Cafeteria Breath Guard.

One Piece Breath Guard Installation

Some units are shipped with a breath guard not installed. To install the breath guard follow these steps:

NOTE:
Use caution when tightening the cap nuts. Overtightening may cause the plastic to crack.

Install the breath guard uprights (A) to the studs (B) securing with cap nuts (C) as shown. See Figure 1. Repeat for all four uprights.
Install the breath guard support tube (D) between the uprights (A) securing with cap nuts (C) as shown. Repeat on the other side.
Install the one piece breath guard (E) securing with screws (F) and cap nuts (C) as shown. Repeat for all four mounting locations.
Install the side breath protector (G) to the support tube (D) securing with cap nuts (C) as shown. Repeat on the other side.

Three Piece Breath Guard Installation

Some units are shipped with a breath guard not installed. To install the breath guard follow these steps:

NOTE:
Use caution when tightening the cap nuts. Overtightening may cause the plastic to crack.

Install the breath guard uprights (A) to the studs (B) securing with cap nuts (C) as shown. See Figures 1 and 2. Repeat for all four uprights.
Install the breath guard support tube (D) between the uprights (A) securing with cap nuts (C) as shown. Repeat on the other side.
Install the side breath guards (E) securing with screws (F) and cap nuts (C) as shown. Repeat for all mounting locations.
Install the side shield (G) to the support tube (D) securing with cap nuts (C) as shown. Repeat on the other side.
Install the support bar and stud assembly (H) to the side breath guards (E).
Repeat for all mounting locations.
Install the top breath guard (I) to the support bar and stud assembly (H) securing with cap nuts (C). Repeat for all mounting locations.