ZAXCOM QRX200 200 MHz Wide-Band ENG Receiver User Manual
- June 1, 2024
- ZAXCOM
Table of Contents
- ZAXCOM QRX200 200 MHz Wide-Band ENG Receiver
- Product Information
- Product Usage Instructions
- QRX200 Receiver
- Home Screen
- Main Menu
- Dual mode scanning
- Set Scan Range
- Extended Menu
- AES Recognize
- Encryption Code Set
- Frequency Presets
- Firmware
- Wiring Diagrams
- Serial Loop Connector – USB (RS-485)
- Operating Frequencies
- Specifications
- Product Support
- Zaxcom Warranty Policy and Limitations
- Declaration of Conformity
- FCC Notice
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
ZAXCOM QRX200 200 MHz Wide-Band ENG Receiver
Specifications
- Model: Zaxcom QRX200
- Release Date: October 2019
- Firmware Version: QR2-413
- Receiver Flexibility: Ultimate
Product Information
Front Panel Features:
- OLED Display
- INC Key – Used to increase menu parameters
- UHF Antenna Connectors (2) – SMA connectors
- Menu Key – Navigate menu items
- Dec Key – Used to decrease menu parameters
- Receiver Status Indicators:
- Green – Valid signal reception
- Red – No valid signal reception
- A/B Key – Switch between dual receivers
- Power Key – Power control for the QRX
Rear Panel Features:
- DC Power Input – Switchcraft 761K connector
- Audio out connectors (2) – TA5M for analog or AES audio output
Side Panel Features:
Side Mounted LEDs for visual RF and audio reception indication.
Product Usage Instructions
Power Up/Down:
To power up the QRX, press and hold the Power Key for 2 seconds. To power
down, press and hold for 5 seconds.
Menu Navigation:
Use the Menu Key to navigate through different menu items. INC Key
increases parameters, and Dec Key decreases them.
Audio Output:
Connect audio devices to the Audio out connectors on the rear panel. Set
audio assignments in the extended menu as needed.
Receiver Operation:
The QRX has two individual receivers (A and B). Monitor incoming audio
levels and transmitter battery status on the Home Screen.
FAQ
- Q: How do I update the firmware on the QRX using a transmitter?
A: To update firmware, follow the instructions provided in the user manual under the Firmware section.
QRX200 Receiver
Front
-
OLED Display
-
INC Key – Used to increase the parameters of a menu item.
-
UHF Antenna Connectors (2) – SMA connectors.
-
Menu Key – Press to advance to the next menu item.
-
Dec Key – Used to decrease the parameters of a menu item
-
Receiver Status Indicators
Green – Receiver is receiving a valid signal.
Red – Receiver is not getting a valid signal. -
A/B Key – Press to alternate between receivers in dual mode.
-
Power Key – Press and hold for 2 seconds to power up the QRX. Press and hold for 5 seconds to power down the QRX.
Rear
-
DC Power Input – The QRX uses a Switchcraft 761K connector.
-
Audio out connectors (2) – TA5M
These connectors will output the audio from the QRX. The same connectors can be used to output either analog audio or AES audio. The audio assignments for the TA5 connectors are set in the extended menu. -
Serial Loop -The USB style connectors on the back of the QRX allow multiple QRXs to share a single common QIFB option. For example one master QRX with a QIFB option board can be connected to 3 QRXs with no option boards. The QRXs without option boards will behave as if they have an IFB option board and will send remote control commands over the serial link to the master QRX.
Please note the USB connectors are NOT generic USB connectors that can be used as a connection to any computer. These are used to exchange RS-422/RS-485 commands and a special cable is required to do this please see the wiring diagram section of this manual for more information.
Side
Side Mounted LEDs – The LEDs give visual indication if RF and / or audio are being received by the QRX. The LED settings are adjusted in the extended menu. There are three LEDs per group and one group for each receive channel. The group to the top represents channel one, the group below is channel 2, the next group is channel 3, and the group on the bottom is channel 4.
LED modulation colors
Home Screen
Receiver
The QRX has two individual receivers the A (left receiver) and the B (right
receiver).
Audio level
Indicates the incoming audio level for each receiver, the meter extends from
the left to the right. The two vertical bars to the right are the -20dBFS and
-10dBFS mark.
Transmitter’s battery level
The battery diagram displays the transmitter’s battery level. The battery type
being used in the transmitter needs to be set in the transmitters extended
menu. The battery symbol will start to blink just before transmitter shuts
down.
Transmitter’s record status
- S (STOP) The transmitter is stopped.
- R (REC) The transmitter is recording.
- P (PLAY) The transmitter is playing back.
RF signal strength
This shows the radio signal strength of the corresponding transmitter. The RF
signal is depicted as a staircase pattern with the lowest step (low signal
strength) on the left and building up as it progresses to the right (higher
signal strength). When more stairs are showing the stronger the signal is.
Receiving antenna
⇐ Indicates the signal is being received by antenna 1 (left antenna connector)
⇒ Indicates the signal is being received by antenna 2 (right antenna
connector)
Main Menu
Navigating the Main Menu
- To enter the main menu – press the MENU key.
- To advance to the next menu press the MENU key again.
Exiting the Main Menu
- To exit the main menu at any time press and hold the MENU key for 1.5 seconds.
Frequency Adjust
The frequency select menu is where the QRX’s receive frequencies are set. These frequencies need to match the frequencies that are set on the corresponding transmitters.
Adjusting the receive frequency of the QRX
-
Press the INC key and DEC key to adjust the frequency.
-
In dual receive mode pressing the A/B key will toggle between the A and B receiver.
The > will indicate the receiver being adjusted. -
Please note that when in dual receive mode the A and B frequencies needs to be within 35MHz of each other. If the frequency difference is more than 35MHz “TOO BIG” or “TOO SMALL” will flash on the screen to warn that the difference is greater than 35MHz and the frequency will need to be adjusted.
Transmitter Gain Adjust
This menu is only available when transmitter remote control is set to “ON” in
the extended menu.
The transmitter gain menu allows for the input gain on the transmitter to be remotely adjusted when a QRX100 or QRX235 with an IFB option board is connected via the serial loop. The transmitter gain menu will display the gain level and an audio meter with a -20dBFS and -10dBFS mark on the right.
Adjusting the transmitter gain remotely
- Press the INC key to increase the transmitters gain. As the gain is increased“+ + +” will replace the gain level.
- Press the DEC key to decrease the transmitters gain. As the gain is decreased “- – -” will replace the gain level.
- When in dual mode pressing the A/B key will toggle between the two transmitters.
Unit Code Select
This menu is only available when transmitter remote control is set to “ON” in
the extended menu.
This menu sets the unit code that will correspond to the transmitter that is being controlled. The unit code is a unique number used to identify a transmitter within a particular group. This allows individual transmitters that are within the same group to be independently controlled. Unit codes can be any number from 1 to 200.
Test Tone Output
From the tone menu a 1K test tone can be enabled. The tone will be outputted from the TA5 connectors. This is used to set levels and check routing. Pressing the INC and DEC key will cycle through the different tone settings.
- OFF – No tone is being outputted.
- -20dBFS -Tone is simultaneously sent to all 4 outputs at -20dBFS.
- CHAN-ID -Tone is sequentially sent to each channel one at a time at -20dBFS.
- +0dBFS – Simultaneously sends tone to all 4 channels at 0dBFS (full scale)
Frequency Scan
The frequency scan menu is where the QRX can scan the user specified frequency range and search for a clear frequency. After the scan is complete a graphical display of the RF that is present, in that specified range will be shown and the QRX200 will suggest a clear frequency. That frequency can be accepted by pressing the INC key. Or press the DEC key to skip the first chosen frequency and have the QRX200 suggest another frequency.
Single mode scanning
- Turn off the transmitter.
- Press the INC key to initiate a scan.
- While the QRX is scanning, the frequency being examined is displayed on the bottom half of the screen and a graphic map of the RF that is found will be displayed with a vertical line extending up from the baseline. The length of the line indicates the level or strength of the found RF at that frequency.
Selecting a frequency
When the scan is complete a suggested frequency will be shown and a vertical blinking line will be drawn on the display.
At that point:
- Press the INC key to accept the frequency.
- Press the A/B key or the DEC key to suggest another frequency.
Dual mode scanning
In dual mode the two operating frequencies must be within 35MHz of each other.
Pressing the INC key will scan the full chosen scan range (scan range is set
in the next menu) and recommend a frequency from the entire range. If a second
frequency is being chosen to work with a previous chosen frequency, press the
DEC key to limit the scan to a 70MHz window which is 35MHz above and 35MHz
below the other selected frequency. After a scan is triggered, by either
pressing INC or DEC key, the QRX will scan and suggest a frequency. After the
scan is completed that frequency can be accepted or rejected the same way as
in single mode. If an exclamation point appears after the suggested frequency
that is a warning that the shown frequency is more than 35MHz away from the
other frequency. That frequency can be selected provided a new frequency that
is within 35MHz of this frequency will be selected for the other receiver.
Please note that after the first scan turn on the first transmitter and set it
to the chosen frequency, this way when the scan is performed for the second
transmitter the QRX will not select the same, or adjacent, frequency. To
toggle between scanning RXA and RXB press the A/B key.
Set Scan Range
The scan range menu sets what frequency range that the QRX200 will scan when doing a frequency scan. Pressing the INC and DEC key will cycle through the scanning options. If the scan range is changed the QRX200 will automatically jump back to the scanning menu when the MENU key is pressed.
Available Scan Ranges
- All 200 – All frequencies from 512.0MHz through 698.0MHz will be scanned.
- LO 100 – Corresponds to the frequency range of TRX3.5 transmitters, when selected frequencies from 512.0MHz through 614.0MHz will be scanned.
- HI 100 – Corresponds to the frequency range of TRX3.6 transmitters, when selected frequencies from 596.0 through 698.0MHz will be scanned
- BLK (20 -26) – Allows the QRX to scan a specific block (Blocks 20-26).
- Block 20 518-542 MHz
- Block 21 536-572 MHz
- Block 22 560-590 MHz
- Block 24 614-644 MHz
- Block 25 638-668 MHz
- Block 26 662-698 MHz
Extended Menu
Navigating the Extended Menu
- Press and hold the DEC key from the home screen to enter the extended menu.
- To advance to the next menu press the MENU key.
- Press and hold the MENU key at any point to return to the top of the extended menu.
Exiting the Extended Menu
- To exit the extended menu – press the POWER key briefly.
Modulation Select
From this menu the modulation mode is selected. Modulation is simply the way a transmitter “modulates”, or sends, its signal to the QRX200. This setting needs to match the modulation mode that the corresponding transmitter is set to – if the two setting do not match the QRX will not be able to receive and decode the signal from the transmitter. Please note the QRX will need to be rebooted after a change is made to the modulation.
| STEREO| MONO| XR| ZHD 96| ZHD 48
---|---|---|---|---|---
Modulation Bandwidth| 200 kHz| 200 kHz| 200 kHz| 96 kHz| 48 kHz
Minimum Channel to Channel Spacing| 400 kHz| 400 kHz| 400 kHz| 200 kHz*| 100
kHz**
6 MHz TV Channel Capacity| 15| 15| 15| 30| 60
Latency| 6ms| 3.5ms| 6ms| 6ms| 18ms
Compatibility with a 200 Series Receiver| 2 Transmitters| 2 Transmitters| 2
Transmitters| 2 Transmitters| 1 Transmitter
Compatibility with a 300-96 Receiver| NO| NO| NO| 1 Transmitter| 1 Transmitter
Compatibility with a 300-48 Receiver| NO| NO| NO| NO| 1 Transmitter
- When used with a QRX300-96 receiver – the minimum spacing is 300 kHz when using all other receivers.
- When used with a QRX300-48 receiver – the minimum spacing is 200 kHz when using all other receivers.
Single / Dual Mode Select
- SINGLE – This configures the QRX to operate as a single receiver. In single mode the QRX can receive one audio channel from one transmitter.
- DUAL – This configures the QRX to operate as two independent receivers. In dual mode the QRX can receive audio from two transmitters.
AES Output Enable
This menu enables the TA5 connectors to output an AES signal.
- ON – Indicates that the TA5 will output AES audio.
- OFF – Indicates that the TA5 will output analog audio.
Output Assignment
This menu is only available when the QRX is set to dual receive mode.
This menu sets what audio is outputted from each TA5 connector when the QRX is set to dual mode receiving mono transmitters.
- SPLIT / NORMAL – The signal from each transmitter will be outputted on individual TA5 connectors. Transmitter 1 will be outputted on TA5 1 and transmitter 2 will be outputted on TA5 2.
- COMBINED / SWAP – The signal from each transmitter will be combined on a single TA5 connector.
Transmitter Remote Control Enable
Transmitter remote control turns on the ability to remote control the corresponding transmitter when connected to a QRX235, via the serial loop. When connected and enabled QRX200 will have the ability to remotely change the gain, UHF frequency and power level of the corresponding transmitter in addition to changing the transport status of the onboard recorder. Please note that the QRX235 will need to have a QRX option board installed.
Serial Port Assign
This menu sets the function of the serial port on the QRX.
- OFF – No commands will be communicated to the serial port.
- ZAXLAN QRX – The QRX will communicate commands to a QRX235, with QIFB, via the serial port.
- BLUE TOOTH – This setting allows a QRX235 with QIFB will interface to communicate with a ZaxMote blue tooth dongle via the serial port.
Output Routing
This menu is only available when the QRX is set to single receive mode.
This menu sets the output assignments of the TA5 connectors when the QRX is set to single mode and is receiving a signal from a stereo transmitter.
QRX Software Update
The software update menu is where a firmware update for the QRX is initiated from. After the INC key is pressed the QRX will wait for firmware to be sent from a TRX transmitter. When the QRX receives the firmware the update process will automatically begin. Please note the QRX needs to be set to mono modulation and in single mode to update the firmware. Please see the firmware section in the back of this manual for additional information on updating the QRX.
AES Recognize
The AES recognize is used for some Sony F5 or F55 cameras that cannot recognize the AES signal from the QRX.
- OFF – The QRX will output a normal AES signal.
- ON: AB KEY – This setting will send a special signal to the AES out, when the A/B key is pressed. This will allow the Sony camera to recognize and lock to the AES signal from the QRX. This is the recommended setting.
- ON: ALWAYS – The QRX will constantly send a special recognize signal via the AES out.
AES Output Sample Rate Adjust
This menu adjusts the AES output sample rate.
- Normal – This is the recommended setting.
- 96K – The QRX will output a 96 kHz AES signal for some mixers like the Yamaha 01V that cannot properly sample rate convert the AES signal.
LED Brightness Set
This menu sets the brightness level of the side mount LED’s.
- OFF – The LEDs do not illuminate.
- NUMERIC VALUE – Adjustable brightness levels.
- BRIGHT – The LED’s will illuminate at the brightest setting.
Blue LED Set
This menu sets the action of the bottom LED in each group (total of 4 groups). The side mount LEDs were designed to give visual confirmation that audio is being received at the QRX. This menu gives the option to display that a valid RF signal is getting to the QRX even if no audio is being sent.
- OFF – The bottom LED will only display the audio modulation and the blue LED is disabled.
- BLUE FULL TIME – Turns the bottom LED blue for each channel that is receiving a valid RF signal. When the audio has gotten to the point of displaying a level for that channel, the bottom LED will continue to show blue but with a tint of the appropriate modulation color of that channel’s LEDs.
- BLUE PART TIME – Turns the bottom LED blue for each channel that is receiving a valid RF signal. Once the audio is received, the blue is replaced with the appropriate modulation color for that channel.
Encryption Code Set
The encryption menu is where the encryption is turned on and the code is set. The encryption code needs to match the encryption code of the associated transmitters. If an encryption code is set on the transmitter the transmitted audio will be encrypted and can only be listened to if the QRX has the same matching encryption code entered. When the codes do not match, all that will be heard is white-noise. These two sets of numbers are formed into a single six-digit encryption code which provides a total of 16,777,216 possible combinations. For non-encrypted operations all six numbers should be set to 0.
Adjusting the encryption code
- Press the A/B key to advance to the next character.
- To change the designated character, press the INC or DEC key.
- To exit this page, press and hold the MENU key.
Frequency Presets
The QRX has 16 user assignable frequency presets.
Access and navigating the channel preset menu:
- From the home screen press and hold the DEC key for 1.5 seconds which will access the extended menu, then press the DEC one more time to access the channel preset menu.
- When in the channel preset menu pressing the MENU key will cycle through the 16 presets (0 through 15).
- To adjust each preset frequencies press the INC and DEC key.
- To advance to the next preset press the MENU key.
- To exit the preset menus briefly tap the PWR key.
Selecting preset frequencies:
- From the frequency adjust menu press and hold the DEC key until the QRX frequency reaches the minimum frequency of 512.0MHz. Then continue to press the DEC key to access the 16 preset frequencies.
- Pressing the INC and DEC keys will cycle through the 16 preset frequencies.
Firmware
Each unit is shipped with the latest firmware version installed. Each time a unit is powered up, the firmware version number is displayed briefly on the screen. As newer firmware becomes available, it can be downloaded from the Zaxcom website: http://www.zaxcom.com/software-updates
Updating the QRX firmware using a transmitter
- Format a micro SD card in a transmitter.
- With a computer take the formatted card and perform the following:
- Delete the “SNXXXX.ME” file from the card.
- Download the new QRX firmware and load it into the card. (QR2-XXX.BIN)
- Insert the card and a fresh set of batteries into the transmitter.
- At the QRX:
- Verify the QRX is set to single mode and modulation is set to mono.
- Verify encryption is off (ID1 and ID0 are both set to 000)
- Set the UHF Frequency to the same frequency as the programming transmitter.
- The QRX receiver status LEDs should both be green.
- From the extended menu go to the firmware update page and press the INC key.
- The screen will display waiting for program. This indicates the receiver is ready to download the new firmware. This can be done to several QRXs so they will be updated at the same time.
- At the transmitter proceed to the setup menu choose to the firmware update menu (see transmitter manual) and press the INC key.
- Each QRX should indicate it is receiving the program.
- After the firmware send cycle, all of the receivers should be re-programmed and “SUCCESS . . . REBOOT NOW” will be displayed. If there was a reception error, the affected receiver will automatically restart the process with the start of the next send cycle.
- Reboot the QRX and verify the QRX is running the new firmware version.
WARNING: After the QRX has received its entire program, it will erase and burn its firmware into the ROM. During this process, which only takes a few seconds, you MUST NOT turn ‘OFF’ the QRX. If the program is never fully received, it is safe to cycle the power.
Wiring Diagrams
Audio Output Connectors
There are two TA-5M connectors on the back panel. How they are used varies
based on the output configuration in the extended menu.
Single Analog Channel out of one TA5
Two Analog Channels out of one TA5
AES Digital out of TA5
The TA-5 connectors can also be used to output AES digital audio. Each TA5
will output a stereo pair on pins 1, 2 and 3 with pin 1 being ground. When
receiving audio from a mono transmitter the QRX will output the same audio on
both pairs of the TA5. When receiving audio from a stereo transmitter the QRX
can output both signals on a single TA5.
IMPORTANT: While sending digital audio, it is necessary that the unit on
the other end (recorder, mixer, etc.) have digital inputs with sample rate
convertors, as there is no way to synchronize the output data with the
recorder’s digital input.
Serial Loop Connector – USB (RS-485)
The serial connectors allow for communication between several QRXs. This allows QRXs that do not have the IFB option to connect to a single QRX that does have the IFB option.
Operating Frequencies
UHF – Audio
512.0 MHz to 698.0 MHz (Blocks 20 through 26)
Antenna Cutting Chart
ZAXCOM
www.zaxcom.com
Specifications
Receiver
- RF Modulation: Proprietary digital method
- RF Frequency Range: 512.0 to 698.0 MHz
- RF Frequency Step: 100 KHz
- Channel Separation: 500 KHz (700 KHz recommended)
- Sensitivity: -110 dBm
- Antenna Connector: 50-ohm SMA female
Receiver Audio – Analog Outputs
- Channels: Up to 4
- Audio Level: Line Level 0 dBu active balanced
- Dynamic Range: 114 dB
- Distortion: 0.001%
- DAC Bit-depth: 24 bit
- Connector (x 2): TA-5M
Receiver Audio – Digital Outputs
- Channels: Up to 4
- AES Reference: Wordclock and AES reference
- Connector: TA-5M
Serial Control
- Protocol: RS-422, RS-485
- Connector (x 2): USB
Physical
- Weight: 6.0 oz. (170 grams)
- Dimensions (H x W x D): 1.25” x 3.25” x 5.25” (32mm x 83mm x 133mm)
- External Power: 9 to 18 VDC (270 mA @ 12 VDC – no side LEDs, 390 mA – w/ LEDs illuminated)
- Internal Power: N/A
- Display: OLED panel
Product Support
- Register your product with Zaxcom: http://zaxcom.com/support/product-registration/
- Download the latest Firmware from: http://zaxcom.com/support/updates/
- Download the latest User Manuals from: http://zaxcom.com/support/updates/
- Submit Technical Questions at: http://www.zaxcom.com/submit-a-technical-question
- Submit information for Repair Services at: http://www.zaxcom.com/support/repairs
- Join the Zaxcom User Forum at: http://www.zaxcom.com/forum/forum.php
- Join the Zaxcom Face Book User Group at: https://www.facebook.com/groups/682199065139938/
Zaxcom Warranty Policy and Limitations
Zaxcom Inc. values your business and always attempts to provide you with the very best service. No limited warranty is provided by Zaxcom unless your QRX (“Product”) was purchased from an authorized distributer or authorized reseller. Distributers may sell Product to resellers who then sell Product to end users. Please see below for warranty information or obtaining service. No warranty service is provided unless the Product is returned to Zaxcom Inc. or a Zaxcom dealer in the region where the Product was first shipped by Zaxcom.
Warranty Policy
The Product carries a Standard Warranty Period of one (1) year.
NOTE: The warranty period commences from the date of delivery from the
Zaxcom dealer or reseller to the end user.
There are no warranties which extend beyond the face of the Zaxcom limited
warranty. Zaxcom disclaims all other warranties, express or implied, regarding
the Product, including any implied warranties of merchantability, fitness for
a particular purpose or non-infringement. In the United States, some laws do
not allow the exclusion of the implied warranties.
Troubleshooting & Repair Services
No Product should be returned to Zaxcom without first going through some basic
troubleshooting steps with the dealer you purchased your gear from. To return
a product for repair service, go to the Zaxcom Repair Services page
http://www.zaxcom.com/repairs and fill in your information; there is no need
to call the factory for an RMA. Then send your item(s) securely packed (in the
original packaging or a suitable substitute) to the address that was returned
on the Repair Services page. Insure the package, as we cannot be held
responsible for what the shipper does. Zaxcom will return the warranty
repaired item(s) via two-day delivery within the United States at their
discretion. If overnight service is required, a FedEx or UPS account number
must be provided to Zaxcom to cover the shipping charges.
*Please note a great resource to troubleshoot your gear is the Zaxcom Forum: http://www.zaxcom.com/forum.
Warranty Limitations
Zaxcom’s limited warranty provides that, subject to the following limitations,
each Product will be free from defects in material and workmanship and will
conform to Zaxcom’s specification for the particular Product.
Limitation of Remedies
Your exclusive remedy for any defective Product is limited to the repair or
replacement of the defective Product. Zaxcom may elect which remedy or
combination of remedies to provide in its sole discretion. Zaxcom shall have a
reasonable time after determining that a defective Product exists to repair or
replace a defective Product. Zaxcom’s replacement Product under its limited
warranty will be manufactured from new and serviceable used parts. Zaxcom’s
warranty applies to repaired or replaced Product for the balance of the
applicable period of the original warranty or thirty days from the date of
shipment of a repaired or replaced Product, whichever is longer.
Limitation of Damages
Zaxcom’s entire liability for any defective Product shall, in no event, exceed
the purchase price for the defective Product. This limitation applies even if
Zaxcom cannot or does not repair or replace any defective Product and your
exclusive remedy fails of its essential purpose.
No Consequential or Other Damages
Zaxcom has no liability for general, consequential, incidental or special
damages. These include loss of recorded data, the cost of recovery of lost
data, lost profits and the cost of the installation or removal of any Product,
the installation of replacement Product, and any inspection, testing or
redesign caused by any defect or by the repair or replacement of Product
arising from a defect in any Product. In the United States, some states do not
allow exclusion or limitation of incidental or consequential damages, so the
limitations above may not apply to you. This warranty gives you specific legal
rights and you may also have other rights, which vary from state to state.
Your Use of the Product
Zaxcom will have no liability for any Product returned if Zaxcom determines
that:
- The Product was stolen.
- The asserted defect:
- Is not present,
- Cannot reasonably be fixed because of damage occurring when the Product is in the possession of someone other than Zaxcom, or
- Is attributable to misuse, improper installation, alteration, including removing or obliterating labels and opening or removing external covers (unless authorized to do so by Zaxcom or an authorized Service Center), accident or mishandling while in the possession of someone other than Zaxcom.
- The Product was not sold to you as new.
Additional Limitations on Warranty
Zaxcom’s warranty does not cover Product, which has been received improperly
packaged, altered or physically abused.
Declaration of Conformity
ZAXCOM, INC.
230 West Parkway, Unit 9
Pompton Plains, NJ 07 444
September 1, 2019
We certify and declare under our sole responsibility that the following
product: QRX200, QRX235, QRX212, MRX214, RX-12, RX-12R, RX200 and URX100
wireless
microphone receivers Restrictive use for residential, office and professional
use only Conforms with the essential requirements of the EMC Directive
2004/108/EC and
R&TTE Directive 99/5/EC, based on the following specifications applied:
- EN 300 422-2 v1 .3.1 Radio Parameters
- EN 301 489-9 v1 .4.1 Immunity
- EN 60950: 2006/A 1 :2011 Product Safety (low voltage directive)
- EN 50566: 2013 RF Exposure Safety
Our authorized representative in Europe is Mr. Roger Patel, Director of
Everything Audio located at Elstree FIim Studios, Shenley Road, Borehamwood,
Herts WD61 JG in England.
Glenn Sanders
President
Zaxcom, Inc.
Zaxcom, Inc.
230 West Prkwy, Unit 9
Pompton Plains, NJ
07444 USA
zaxcom.com
973.835.5000 (tel)
973.835.6633 (fax)
FCC Notice
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. The equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna
- Increase the separation between the equipment and receiver
- Connect the equipment into an outlet on a circuit different from that which the receiver is connected
- Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications to this equipment not expressly approved by Zaxcom, Inc. could void the user’s authority to operate it.
References
- Forums - Zaxcom Forums
- Forum - Zaxcom Forums
- Zaxcom » Repair Submission Form
- Zaxcom » Repair Submission Form
- Zaxcom » Product Registration
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>