smappee EVW-332-BR-E-W EV Wall Lite 22kW 3 Phase Socket Instruction Manual

: June 1, 2024
: smappee

Table of Contents

smappee EVW-332-BR-E-W EV Wall Lite 22kW 3 Phase Socket
Product Information
Product Usage Instructions
Introduction
Safety instructions
Models
Components
Technical specifications
Preparing the installation
Installation and activation
Using the EV Wall Lite
- LED status
Declaration of conformity
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

smappee EVW-332-BR-E-W EV Wall Lite 22kW 3 Phase Socket

Product Information

Specifications

Output power:
- Single-Phase: 7.4 kVA
- Three-phase: 22 kVA
Charge mode: Mode 3 (IEC 61851)
Connection case: Case A and B (Socket) (IEC 61851)
Metering: kWh meter compliant with IEC 62053-21
Integrated Residual Current Protection: Rated operating residual current detection: 6 mA DC
Supported power systems: TN-C, TN-C-S, TT, IT 1
Grounding:
- TN system: PE wire
- TT system: Independently installed ground electrode < 100 Ohm spreading resistance
- IT system: connected to a shared reference (common earth) with other metal parts

Product Usage Instructions

Introduction
Thank you for purchasing the Smappee EV Wall Lite charging station for electric vehicles. To ensure a safe and proper installation, carefully read and follow the instructions provided in this manual.
Safety Instructions
Safety Warning:
Before installation, servicing, or use, read and adhere to all safety instructions. Ensure installation complies with national and local regulations by a qualified electrician.
Safety Precautions:
- Risk of electric shock. Exercise caution.
- Refer to the accompanying documentation when you see the specified symbol.
- Avoid overlapping loops of the charging cable to prevent overheating.
Models****
Article no.| EAN| Description
---|---|---
EVWL-332-BR-E-W| 5425036933989| EV Wall Lite 3-Phase 22 kW Socket
EVWL-332-BSR-E-W| 5425036933996| EV Wall Lite 3-Phase 22 kW Socket with shutter
Components
The components included with the product are detailed in the user manual.
Technical Specifications****
Feature| Description
---|---
Output power| Single-Phase: 7.4 kVA Three-phase: 22 kVA
Charge mode| Mode 3 (IEC 61851)
Connection case| Case A and B (Socket) (IEC 61851)
Metering| kWh meter compliant with IEC 62053-21
Integrated Residual Current Protection| Rated operating residual current detection: 6 mA DC
Supported power systems| TN-C, TN-C-S, TT, IT1
Grounding| TN system: PE wire; TT system: Independently installed ground
electrode <100 Ohm spreading resistance; IT system: connected to
a shared reference with other metal parts

FAQ

Q: Who should install the Smappee EV Wall Lite?
A: Only qualified electricians or equivalent individuals should install the Smappee EV Wall Lite for safety and proper functioning.
Q: How can I contact Smappee for support?
A: You can contact Smappee at support@smappee.com for assistance or inquiries.
Q: What should I do if my local distributor cannot assist me?
A: If your local distributor is unable to help, reach out to Smappee directly for further assistance.

Document Accuracy
The specifications and other information in this document were verified to be accurate and complete at the time of its publication. Due to ongoing product improvement, this information is subject to change at any time without prior notice. For the latest information, see our online documentation: https://www.smappee.com/downloads.

Introduction

Thank you for purchasing this Smappee EV Wall Lite charging station for electric vehicles for charging at home.
This installation and user manual tells you how to install and use the Smappee EV Wall Lite. We advise you to read the contents of this manual carefully, to ensure a safe and proper installation.

Support

Only qualified electricians or equivalent may install the Smappee EV Wall Lite. If you have any questions, please contact your service partner.
Please have the following information ready to speed up the process: article number and serial number which you can find on the identification label of the charging station.

Should your local distributor be unable to help you, or you have a suggestion for us, you can contact Smappee at: support@smappee.com.

Smappee n.v.
Evolis 104 8530 Harelbeke Belgium

Safety instructions

Safety warning
Fully read and follow the safety instructions below before you install, service, or use your Smappee EV Wall Lite. The installer must ensure that the charging station is installed according to the relevant national and local regulations.
Carrying out activities on this charging station without the relevant knowledge and qualifications can lead to serious accidents and death. Only carry out tasks for which you are qualified and have been fully instructed. Incorrect installation, repairs, or modifications can result in danger to the user and may void the warranty and liability.

Safety precautions

CAUTION: Risk of electric shock.
CAUTION: Refer to the accompanying documentation whenever you see this symbol.

Please observe the following safety precautions to avoid potential electric shock, fire, or personal injury:

The charging station is intended exclusively for charging electric vehicles and, when installed correctly, may be used by untrained individuals.
Switch off the electrical power supply to your charging station before installation or maintenance work.
Do not use the charging station if damaged / defective.
Do not immerse the charging station in water or any other liquids.
Do not expose the charging station to heat, flame, or extreme cold.
Do not attempt to open, repair, or service any parts. Contact Smappee or your service partner for further information.
Only use the charging station under the specified operating conditions.
Do not allow children to operate a charging station.
When a charging station is in use, adult supervision of any children present is required.
While charging the charging cable must be completely unwound and connected to the electric car without overlapping loops. This is to avoid the risk of overheating the charging cable.

Maintenance

Observe the maintenance schedule.
Clean the outside only with a dry, clean cloth.
Do not use abrasive agents or solvents.
May not be carried out during rain or if air humidity exceeds 95%.

Keeping order

After charging store the charging cable properly so it does not present a tripping hazard.
Make sure the charging cable cannot become damaged (kinked, compressed, or driven over).
Do not place any objects on the charging station.

Transport and storage

Disconnect the electrical power supply before removing the charging station for storage or relocation.
Only transport and store the charging station in its original packaging. No liability for damage incurred will be accepted if the charging station is transported in non-standard packaging.
Store the charging station in a dry environment within the temperature range specified in the technical specifications.

Models

Article no.	EAN	Description
EVWL-332-BR-E-W	5425036933989	EV Wall Lite 3-Phase 22 kW Socket
EVWL-332-BSR-E-W	5425036933996	EV Wall Lite 3-Phase 22 kW Socket with

shutter

Components

Components included

$smappee-EVW-332-BR-E-W-EV-Wall-Lite-22kW-3-Phase-Socket-Fig- $1$$

Identification label
The identification label of your charging station is located on the left inner side of the EV Wall Lite.

$smappee-EVW-332-BR-E-W-EV-Wall-Lite-22kW-3-Phase-Socket-Fig- $2$$

Manufacturer
Article number
Rating
Operating temperature
Manufacturing date
QR code containing article number and serial number
Serial number
Degree of protection
EAN code

Technical specifications

Feature

|

Description

---|---
Technical features
Output power| Single-Phase: 7.4 kVA

Three-phase: 22 kVA

Charge mode| Mode 3 (IEC 61851)
Connection case| Case A and B (Socket) (IEC 61851)
Metering| kWh meter compliant with IEC 62053-21
Integrated Residual Current Protection| Rated operating residual current detection: 6 mA DC.
Supported power systems| TN-C, TN-C-S, TT, IT 1
Grounding| TN system: PE wire

TT system: Independently installed ground electrode < 100 Ohm spreading resistance

IT system: connected to a shared reference (common earth) with other metal parts

30 mA AC RCD type A or B (according to local regulations)

Caution: not all vehicles support the IT system. In this case or with 3x230V charging, a voltage transformer may be required.

Interfaces & Connectivity

LED brightness 100%: 5 W

Environmental conditions| Indoor and outdoor use
Operating temperature| -25 °C to 40 °C
Storage temperature| -25 °C to 60 °C
Relative humidity| 0 % – 95 %, non-condensing
Maximum installation altitude| 0 – 2.000 m
Access| Locations with restricted and non-restricted access
Physical properties
Dimensions| 300 x 300 x 110 mm
Weight (excluding packaging)| 6.2 kg
Charging cable length| N/A
Supply line connection| Terminal block, flexible conductors up to 6 mm² or solid conductors up to 10 mm²
Stationary/moveable| Fixed installation
External design| Enclosed assembly
Mounting method| Wall
| The operating temperature assumes the ambient temperature of a product delivered in the default enclosure colors RAL9016 (star white) + RAL7021 (black grey). Direct exposure to sunlight may hurt the temperature range.
---|---
If the product is exposed to lower or higher ambient temperatures, continuous operation cannot be guaranteed. If temperatures exceed the maximum values, the charging station will automatically decrease the charging current to decrease the internal temperature of the charging station.

This stabilizes the internal temperature and makes it less likely that a charging session will be unexpectedly paused.

If the product is directly exposed to sunlight, the automated temperature management may automatically start below the maximum ambient temperature. Therefore, wherever possible, avoid exposing the charging station to direct sunlight.
Where products are exposed to the elements of nature, the enclosure can be subject to gradual aging of the material, which can result in product discoloration over time.

Therefore, wherever possible, place the product in a sheltered place to optimize the life of the materials.

Preparing the installation

The first step is to prepare the physical installation of the EV Wall Lite as described in this chapter.

Installation prerequisites

Calculate the existing electrical load to find the maximum operating current for the charging station installation. The Smappee EV Wall Lite is equipped with 1 connector which needs to be powered.
Obtain all necessary permits from the relevant local authority.
Refer to local wiring regulations to select the conductor sizes and use only copper conductors.
Make sure that the installation area of the charging station is adequate for usability and ventilation purposes.
Use the correct tools and provide sufficient material resources and protection measures.

Power supply

The appropriate wire gauge of the supply cable depends on the power rating and distance between the meter cabinet and the charging station. The voltage drop must not exceed 5%. It is advisable to have a maximum voltage drop of 3 %.
The maximum wire gauge that can be fitted is 6 mm² in the case of flexible conductors or 10 mm² when solid conductors are used.
The power supply connection must be protected against short-circuiting and over-current with an individual circuit breaker. This circuit breaker must be 2-pole (for single-phase) or 4-pole (three-phase), curve B or C, and have a current rating of a maximum of 40 A (or otherwise in compliance with local standards and regulations).
An RCD of type A or B (according to local regulations) with a rated residual operating current of 30 mA must also be installed. A charging station connector must always be installed on a dedicated power circuit.
When the power supply and the charging station are part of a TN-S system, the station must be grounded via the main distributor.
Route the power supply cables to the position where the charging station will be installed together with an Ethernet cable for the internet connection (if applicable).
Make sure that there is at least a 30a cm cable available at the location of the EV Wall Lite to be able to connect it easily internally.
Local regulations may be applicable and can vary depending on the region or country.
- The power supply enters the station at the bottom of the housing through the middle cable gland.
- The Cat 5/6 Ethernet cable also enters the charging station via the bottom of the housing.

The maximum power rating for each connector is specified in the table below.

Power per connector| Connection| Input current| Output current
---|---|---|---
7.4 kW| 1-phase| 1 x 32 A| 1 x 32 A
22 kW| 3-phase| 3 x 32 A| 3 x 32 A

Route Ethernet cable
The EV Wall Lite requires a stable internet connection via Ethernet. An RJ45 connector (not supplied) should be attached to the end of the cable.

Prepare the mounting
The Smappee EV Wall Lite is designed to be mounted on a wall. When positioning the EV Wall Lite, take into account that the power supply cables and Ethernet cable are entering the housing at the bottom through cable glands. The central M32 cable gland is for the power supply, and the M20 cable gland is for the Ethernet cable.

Tools (not included)

Screwdrivers
3 mm Hex screwdriver
7 mm socket wrench with extension bar
Multimeter and earth ground meter
Wire stripper and cutter
Needle-nose pliers
Ferrules crimper, when using stranded power supply cables
Drill and rock drill diameter 10 mm
Hammer
RJ45 crimping tool

Supplies (included)

3 x wall plugs and screws (Ø 4.8 mm x 50 mm)
3 x M4 x 6 mm HEX screws

Supplies (not included)

CAT 5/6 Ethernet cable and two RJ45 connectors for internet access
Power supply cables
Ferrules (6 mm²), when using stranded power supply cables
Circuit breaker (max. 40 A)
30 mA RCD Type A or B

Installation and activation

This procedure describes the required steps for the physical installation of the EV Wall Lite.

CAUTION: The installation must be carried out by a qualified professional who has read this manual and works in compliance with IEC 60364 standards. Neglecting this may lead to severe injuries or hazardous situations while working with electricity.

CAUTION: The electric system must be entirely disconnected from every power source before performing installation or maintenance work. Make sure it is not possible to connect the electric current during installation. Put up caution tape and warning signs to mark the work areas. Make sure no unauthorized people can enter the work areas.
CAUTION: The charging station contains electric components that may still contain electrical charge after being disconnected. Wait at least 10 seconds after disconnection before commencing work.
CAUTION: Adaptors or conversion adaptors and cord extension sets are not allowed to be used.

Place the mounting plate in position

Use the mounting plate to mark the position of the screws on the wall where the EV Wall Lite is to be positioned.
Make sure the mounting plate is positioned with the 2 insert holes on the bottom and that it hangs level.
Drill 3 holes of 10 mm diameter through the slots to a depth of 50 mm. Insert the supplied wall plugs into the holes.
Attach the mounting plate, with the 3 bulges facing the wall, to the wall with the supplied screws, as depicted below.

Place the EV Wall Lite in the position

Untighten the two M4 nuts on the back of the front plate and remove the front plate of the EV Wall Lite. Safely put aside the front plate to avoid damaging the PCB-board attached to it. $smappee-EVW-332-BR-E-W-EV-Wall-Lite-22kW-3-Phase-Socket-Fig- $5$$
Attach the EV Wall Lite housing to the mounting plate using the three supplied M4 x 6 mm HEX screws.

Serial number starting with 6222 – Power supply connection

Slide the power cable through the middle cable gland.
Cut the power supply cables to adequate length and add the ferrules to each conductor if stranded cables are used.
Measure the resistance of the grounding circuit and make sure that it is within acceptable limits. If necessary, install a grounding point closer to the charging station.
Connect each power supply cable to the relay board using the connectors labeled with ‘IN’. Respect the phase assignment of L1, L2, and L3.
If you have a single-phase power supply, only the L1, N, and PE wires are connected.

Serial number starting with 6202 – Power supply connection

Slide the power cable through the middle cable gland.
Cut the power supply cables to adequate length and add the ferrules to each conductor if stranded cables are used.
Measure the resistance of the grounding circuit and make sure that it is within acceptable limits. If necessary, install a grounding point closer to the charging station.
Connect each power supply cable to the terminal block.
If you have a single-phase power supply, only the L1, N, and PE wires are connected.

IMPORTANT notes for 3P (3 x 230 V) – Delta topology
This section is only relevant if you have a delta grid topology. This is only found in some parts of Belgium and Norway. If this is not applicable, you can skip this section.

When an EV Wall Lite is installed in a residential installation with a 3P (3 x 230 V) Delta grid connection, some additional requirements need to be taken into account. You can verify whether you have this topology by checking the grid connection to see if the following are true:

There is no neutral wire.
The voltage between the two phases is approximately 230 V.
The voltage between a phase and the earth is approximately 130 V.

Some EVs are not compatible with this type of grid connection due to built-in security in the EV. Contact your EV manufacturer for more information. The security feature that some EVs have is a voltage check between the phase that is connected as neutral and the ground. If this is not 0 volts, the car won’t charge. The presence of this security feature may vary for each manufacturer and each model.

As there is no neutral wire available in this topology, the L3 will be used as neutral. In this case, some EVs will be able to charge dual phase (using both L1 and L2) and some will only charge single phase. In practice, this may limit the maximum charging power. This again varies for each EV manufacturer and each model. If your EV is not compatible with this grid topology, or if you would like to achieve higher charging power than what is possible on a delta grid topology, you can install a transformer. This transformer will convert the 3 x 230 V delta topology to a standard 3 x 400 V + N star topology.

Serial number starting with 6222 – without transformer

If you are connecting the charging station directly to the 3 x 230 V delta grid, without a transformer, please refer to the diagrams below.
As depicted, the L3 connector is left empty. The L3 power supply cable is connected to the N connector block.
We highly recommend that you test compatibility with the customer’s EV during installation. If you have connected the EV Wall Lite as shown above but the EV will not charge, you can try to disconnect the L2 cable going to the socket.
Do not disconnect the L2 of the power supply cable!

Serial number starting with 6202 – Without transformer

If you are connecting the charging station directly to the 3 x 230 V delta grid, without a transformer, please refer to the diagrams below.
As depicted, the L3 connector is left empty. The L3 power supply cable is connected to the N connector block. $smappee-EVW-332-BR-E-W-EV-Wall-Lite-22kW-3-Phase-Socket-Fig- $10$$
We highly recommend that you test compatibility with the customer’s EV during installation. If you have connected the EV Wall Lite as shown above but the EV will not charge, you can try to disconnect the L2 cable going to the socket.
Do not disconnect the L2 of the power supply cable!

With transformer
If a transformer is used to convert the 3 x 230 V delta connection to a standard 3 x 400 V star with neutral, then the charging station’s power supply can be connected as usual. Please refer to the pictures on previous pages for this.

Serial number starting with 6222 – Closure

Attach an RJ45 connector to the Ethernet cable after feeding it through the right cable gland. Plug it into the Smappee Connect.
- As an optional setup, it is possible to remove the Connect from the EV Wall Lite and mount it inside of the building. See “Optional: mount the Connect inside of the building” for more information
Mount the front plate into position by connecting the 12-pin plug to the PCB attached to the front plate. Make sure to hear a click when connecting the 12-pin plug.
Mount and tighten the supplied M4 nuts.

Serial number starting with 6202 – Closure

Attach an RJ45 connector to the Ethernet cable after feeding it through the right cable gland. Plug it into the Smappee Connect.
Mount the front plate into position by connecting the RJ10 cable to one of the B ports of the PCB attached to the front plate.
- Be careful to connect the RJ10 cable to one of the B ports. Do not connect it to the A port.
- The Ethernet cable should be connected to the Smappee Connect, not to the PCB attached to the front plate.
Mount and tighten the supplied M4 nuts.

Switching on the EV Wall Lite

Check all connections are secure and power up the EV Wall Lite.
Check the status LEDs:
- Smappee Connect: blue flashing
- Power Box: green flashing light (1 x per 3 seconds)

Optional: mount the Connect inside of the building
This setup is only applicable to EV Wall Lite units with a serial number starting with 6222.

On some rare occasions, it might be beneficial that the Smappee Connect is removed from the EV Wall Lite and mounted inside of the building.
This might be an option when the owner is concerned about the security of the Internet connection and doesn’t want an Ethernet cable to leave the building.
A second reason might be that the owner opts for a Wi-Fi internet connection and the signal is not strong enough to reach the EV Wall Lite.
It is possible to remove the Connect from the EV Wall Lite and mount it inside the building.
- This kind of setup requires some additional components, which are not included.

Below you find the schematic overview of how this alternative installation can be accomplished.

$smappee-EVW-332-BR-E-W-EV-Wall-Lite-22kW-3-Phase-Socket-Fig- $17$$

Follow the steps below to make the correct interconnections between all components.

Remove the RJ10 data cables from the Connect.
Connect the RJ10 cable from the B-port of the Power Box to one of the B-ports of the relay board.
Pay attention not to connect this cable to the A-port of the relay board.
Mount the Connect in the desired location. To accomplish this, an extra DIN mounting plate or wall mounting plate is necessary (not included).
Route an Ethernet cable for internet connection to the Connect. Connect the Ethernet cable to the RJ45 port of the Connect (not included).
Route an RJ10 data cable from the Connect to the EV Wall Lite. Connect this data cable to one of the B-ports of the Connect (not included).
Route the RJ10 data cable through the right cable gland.
Connect the new RJ10 data cable to the remaining B-port of the relay board.

Pay attention not to connect this cable to the A-port of the relay board.

Activation
This procedure is done with the Smappee mobile app. You can download this from the Apple App Store for iOS or the Google Play store for Android phones.

The Smappee App will guide you through the various steps to fill in all the required information.

Log in to the Smappee App with the given Smappee username or create a new user account.
Install a Smappee car charging station.
Follow the steps shown in the mobile app.

The settings of your charging station can be adjusted in the Smappee Mobile app or Dashboard.

Smappee Mobile App: Name, Maximum current per connector, Charging speed, and LED brightness
Dashboard: Name, Maximum current per connector, charging speed and LED brightness

Using the EV Wall Lite

There are three ways of charging using a Smappee EV Wall Lite:

Plug and charge: Simply connect your cable and start charging.
Swipe and charge: Connect the cable, swipe your card, and start charging.
Scan and charge: Connect the cable, scan the QR code in the Smappee app, and start charging.

Below you can find the different charging sequences.

Each EV Wall Lite that is installed and activated is Plug and charged. Changing the Session Activation Method is done using the Smappee Dashboard.
Changing the authentication methods can be done remotely.
Scan and charge and Swipe and charge (with Smappee CPO) can only be used when a Smappee Payment Package has been signed. See this article for more info.

Plug and charge
The charging station is freely accessible without the need to authorize. Anyone can plug their car into the charger and start charging for free.

Swipe and charge
Charging sessions can be started using an RFID card. You can either use a Smappee Smart Charge Card for free charging or (if activated) a third-party eMSP card to pay for charging sessions.

The RFID reader is found on the front plate of the EV Wall Lite, together with the ambient light.

Whitelist: charging is free with a Smappee Smart Charge Card or any other authorized RFID card. Once the charging cable is plugged in, the user simply swipes their RFID card and the free charging session begins. All authorized cards must first be added to the whitelist using the ‘Whitelisting’ card on dashboard.smappee.net. See this article for more information. Cards can be ordered via the Smappee dashboard.
Public charging: Other EV drivers can use this charging station and pay with an RFID card /token from a third-party eMSP. This can be done through Smappee’s own CPO or a third-party CPO. Public charging is activated using the Smappee dashboard. See the Smappee Academy for more information.
Split Billing: This is aimed at employees who charge their company car at home and need to be reimbursed for the electricity consumption. Split billing agreements must be made for each employee. Starting a charging session is similar to whitelisting but at the end of each month, Smappee Services will send a bill for all employees’ charging sessions to the company. All individual employees will be reimbursed according to the amount of kWh charged. Split billing is activated using the Smappee dashboard. See this article or the Smappee Academy for more information. $smappee-EVW-332-BR-E-W-EV-Wall-Lite-22kW-3-Phase-Socket-Fig- $20$$

Scan and charge
The user pays by credit card (Visa or Mastercard) using the Smappee app. They scan the QR code shown on the charging station and the app will guide them through the process of starting the charging session. It is also possible to set discount rates for specific users. Scan and charge are activated using the Smappee dashboard. See the Smappee Academy for more information.

$smappee-EVW-332-BR-E-W-EV-Wall-Lite-22kW-3-Phase-Socket-Fig- $21$$

More information on how to use the Smappee EV Wall Lite can be found at: support.smappee.com/hc > Smappee EV Line

LED status

$smappee-EVW-332-BR-E-W-EV-Wall-Lite-22kW-3-Phase-Socket-Fig- $22$$

Declaration of conformity

We,
Smappee nv Evolis 104 B-8530 Harelbeke Belgium

following the provision of the following EC Directives:

2014/35/EU The Low Voltage Directive
2014/30/EU The Electromagnetic Compatibility Directive
2011/65/EU RoHS Directive

hereby declare that the product:
EVWL-332-BR-E-W, EVWL-332-BSR-E-W

conforms with the applicable requirements of the following documents

Emissions:

(EN61326-1 : 2013)
- Radiated Emission: EN 55011:2009 / EN 55032:2015 (Class B)
- Conducted Emission: EN 55011:2009 / EN 55032:2015 (Class B) Harmonic current Emission: EN 61000-3-2:2005 +A1:2008 + A2:2009 Flicker: EN 61000-3-3:2008

Immunity:

(EN61326-1 : 2013)
- ESD: EN 61000-4-2:2008 / EN 61000-4-2 :2009
- Radiated immunity: EN 61000-4-3:2006 + A1:2007 + A2: 2010
- Power frequency magnetic field: EN 61000-4-8:2009
- Voltage dips/interruptions: EN 61000-4-11:2004
- Common Mode Immunity: EN 61000-4-6:2008/EN 61000-4-6:2009
- Burst: EN 61000-4-4:2004/EN 61000-4-4:2012
- Surge: EN 61000-4-5:2005/EN 61000-4-5:2006
Safety:
- Metering Function: IEC 61010-1 Ed 3.0 (2010-06) + A1:2016
- AC Charging equipment: IEC 61851-1 (2017) / EN61558-1
Other applicable standards and certifications: IEC 60364, IEC 62192-1, IEC 62192-2