7688 Faberjet Classo Designer Hood Instruction Manual

7688 Faberjet Classo Designer Hood

Specifications

• Product Name: FABERJET CLASSO 7688 Designer Hood
• Model: FABERJET CLASSO 7688
• Control: Push Control
• Dimensions: 677mm

Product Usage Instructions

Installation

1. Drill 4 holes of 6mm diameter at the bottom of the hanging cupboard.
2. Put the one-way valve on the cooker hood.
3. Install the cooker hood on the bottom of the cupboard and tighten it with the enclosed 4 screws.
4. Install the adjusted board on the bottom of the hood to keep out the gap between the hood back and the cupboard.

Operation

To operate the FABERJET CLASSO 7688 Designer Hood:

• Press A to turn off the speed control when the fan is on.
• Press B for low fan speed.
• Press C or D to change the fan speed.
• Press A to turn off the fan.
• Press C for mid-fan speed.
• Press B or D to change the fan speed.
• Press D for high fan speed.
• Press E to turn on/off the light.

From the Manufacturer

• Please read this user manual carefully before attempting to operate the appliance and keep it in a safe place for future reference.
• This appliance and its packaging are produced by processes that minimize waste and respect the environment.
• Please help us to continue this effort to protect the environment by using the appliance efficiently and dispose of the packaging responsibly.

FOR THE USER

Safety Instruction

Warning

PLEASE READ THIS SECTION THOROUGHLY BEFORE ATTEMPTING TO OPERATE THE APPLIANCE

1. To ensure adequate ventilation in the room when the range hood is in use at the same time as gas/fuel-burning cooking appliances (this does not apply to appliances that only discharge the air back into the room).
2. There is a fire risk if cleaning is not carried out by the instructions.
3. To avoid using food products that produce flame under the range hood.
4. Do not “flambé” food (a cooking procedure in which alcohol is added to a hot pan to create a burst of flames) under the range hood.
5. Sufficient air is needed for the proper exhausting of gases through the flue (chimney) of fuel-burning appliances.
6. This appliance is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, and lack of experience and knowledge.
7. To reduce the risk of fire properly exhaust air and ensure to duct air outside. Do not vent exhaust air into spaces within walls, ceilings, attics and crawl spaces.
8. The appliance is not to be used by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction.
9. Children are being supervised not to play with the appliance.

Installation

1. This appliance must be installed or repaired by a qualified technician only.
2. Do not modify any part of this appliance by yourself.
3. Ensure the location in which this appliance is installed has good and permanent ventilation.
4. In ducted mode, there must be one or more permanent air inlets. The air collected must not be discharged into a duct used to blow off smoke from other appliances fed with electricity.
5. The distance between the bench to the lower part of the hood must not be less than 60cm.
6. Use an electrical connector with earth that is correct for your location.
7. To check the voltage in your area corresponds to the appliance as indicated on the rating label.
8. Do not connect the hood to a duct that carries combustion fumes (e.g. fireplace).

WARNING: Intended For Household Use

1. This product is designed for household use only and should never be used for commercial applications.
2. After use, always ensure that all controls are in the “OFF” position.
3. When frying with a gas flame, take particular care not to allow the oil or grease in the pan to catch fire.

Cleaning, Maintenance & Service
It is very important to clean and maintain the grease filters regularly (at least once monthly) to improve its efficiency in eliminating heat and contaminated air in the kitchen. Heavy oil deposits is a fire hazard. Hood surface should be cleaned with soft cloth and non-corrosive detergent.

Important: Never attempt to repair this appliance by yourself. Always refer to qualified Service Technicians.

• For safety precautions, always purchase the original replacement parts.
• Always switch off the power and unplug the connection before conducting maintenance or cleaning.

Electrical Cord

1. To ensure the electrical cord is not exposed to heat, chemicals or sharp objects.
2. If the electrical cord is damaged, it must be replaced by the manufacturer its service agent or qualified electrician.

Hood Description

Ducted or Re-circulating mode

• Depending on your requirement, this appliance can be configured to operate in the ducted or re-circulating modes.
• DUCTED MODE: Fireproof ducting system of 150mm diameter vent the fumes through a suitable outlet. In the ducted mode, only the aluminium grease filters are installed.
• RECIRCULATING MODE: Fumes are filtered for grease and odour through the aluminium grease filters and the charcoal filters respectively and re-introduced into the kitchen environment. In re-circulating mode, both the aluminum grease filters and the charcoal filters should be installed.

Speed Control

1. The hood is equipped with 4-speed electronic controls.
2. Use the low speed for simmering, and medium speed for light cooking. To use the high speed for frying or heavy cooking.

Dimension Diagrams

Side Suction Slim Hood

• FABERJET CLASSO 7688

Instructions for use

Push Control (FABERJET CLASSO 7688)

• Press A, and turn off the speed control when the Fan is on.
• Press B  and the fan runs at low speed. Press C or Press D to change the Fan Speed. Press A, the fan turns off.
• Press C  and the fan runs at mid-speed. Press B or Press D to change the Fan Speed. Press A, the fan turns off.
• Press D  and the fan runs at high speed. Press B or Press C to change the Fan Speed. Press A, the fan turns off.
• Press E , and turn on the light. Press it again, and turn off the light.

Cleaning & Maintenance

SURFACES:
Wash with warm soapy water and a soft sponge. Never use abrasive detergent, scouring pads, steel wool or
solvents on any part of this appliance as this will cause irreparable damage.

ALUMINIUM GREASE FILTERS:
Wash in the dishwashers or soak the panels in a degreasing agent for an hour, then rinse off and dry before re-installing.

CHARCOAL FILTERS:( optional and not included in the package) (only in the re-circulating model): Charcoal cannot be reused. They must be replaced with the appropriate types once a year or depending on the frequency of appliance usage.
For this appliance to function effectively, regular maintenance is a must.
Clogged filters restrict airflow and may cause the motor to overheat.

Installation

• Use suitable bolts to mount the appliance on a secure surface.
• The minimum distance between the supporting surface for the cooking vessels on the hob and the lowest part of the range hood. When the range hood is located above a gas appliance, this distance shall be at least 65 cm. If the instructions for installation for the gas hob specify a greater distance, this has to be taken into account;
• The location of the installation must have permanent ventilation openings.
• Regulations concerning the discharge of air have to be fulfilled.
• It is strongly recommended that the hood be installed right over the exhaust air from cooking.
• It is better not to install the outlet of the pipe in the wind direction, which can prevent the exhaust air from flowing backwards.
• Fasten the components for the exhaust outlet with screws. To ensure good ejection of exhaust air, the pipe must not be bent for too many times.

Way one:

• To install onto the wall drill 2 holes of 08mm in a suitable place according to the centre distance of the hole in the back of the cooker hood.
• Insert the nut into the holes. Py to coker no in a conscious. The two safety vents are positioned on the back casing, with a diameter of 6mm.
• Put the one-way valve onto the cooker hood.

Way two:

• Drill 4 holes of 6mm diameter at the bottom of the hanging cupboard
• Put the one-way valve on the cooker hood, then install the cooker hood on the bottom of the cupboard, tighter the hood with enclosed 4 screws.
• Install the adjusted board on the bottom of the hood in order to keep out the gap between the hood back and the cupboard.

Note:

1. The extendable pipe are optional accessory, not supplied.
2. Take off the protection film before installation.
3. There are 2 methods for ventilation, including ‘ horizontal ventilation’ and ‘ vertical ventilation’.

Please pay attention to the ventilation method when installing.

• Vertical ventilation: See Pic A, please use the tool and take out the round cover before using, and the air can be vented from the top
• horizontal ventilation: See Pic B, please use the tool and take out the round cover before using, and the air can be vented from the back.

The square air outlet for horizontal ventilation is not supplied.

Air ventilation setting

• Outdoor exhausting : Turn the adjuster to the outdoor position (pic.7A), install the outlet, and turn on the cooker hood, and then the air will be vented from the outside outlet.
• Recycling: the recycling mode with carbon filter, Turn the adjuster to indoor position (pic.7B), install the outlet cover, turn on the cooker hood, and then the air can be vented from the inside outlet. See Pic 7D
• Note: The charcoal filter is mounted on the back of the grill and must be changed once every three months.
• Warning: t he charcoal cannot be washed or recycled. It should be changed at most after 120 hours using. The carbon filter shouldn’t be exposed to heat.

• The four hob elements were used in the appliance at most.
• Every hood has to fixing screws to firmly fix the hood in its place.

Installation (Vent inside)
If you do not have an outlet to the outside, an exhaust pipe is not required and the installation is similar to the one shown in the section “installation (Vent outside) »

An activated carbon filter can be used to trap odours.
To install the activated carbon filter, the grease filter should be detached first. Press the lock and pull it downward.

Plug the activated carbon filter into the unit and turn it in a clockwise direction. Repeat the same on the other side.

IMPORTANT NOTES:

1. Ensure the activated carbon filter is securely locked.
2. When an activated carbon filter is attached, the suction power will be lower.
3. To check the electrical connection corresponds to the electrical requirement on the rating plate, which is placed inside the cooker hood. The appliance should now be connected to the electrical supply.
4. Check the appliance is operating correctly by selecting each speed and switching the light bulb on and off.
5. To remove the hanging hook and then slide the lower chimney section downwards, until it rests against the main body of the cooker hood.
6. Use a stainless-steel cleaner and polish on the stainless steel surfaces of the appliance.
7. If you are using the appliance in recirculation mode, you should install the carbon filter. See the “fitting the carbon filter” section on page 21.
8. Every hood has two fixing screws to firmly fix the hood in its place.

FOR THE INSTALLER

Safety Information

1. Electrical connection must be by the local standards and laws.
2. Ensure that the electrical supply complies with the appliance setting, otherwise, do not connect.
3. Ensure the power supply cord is free from any heat source or sharp objects.
4. The electrical connection of this appliance must be soundly earthed. In the event of an electrical short circuit, grounding reduces the risk of electrical shock. If unsure, contact a qualified electrician.
5. Replacement of lamp must not exceed 20W.
6. LED lamps must not exceed 1.5W/7W.

Wire Color Codes:

• Green & Yellow = EARTH
• Blue = NEUTRAL
• Brown = LIVE

Troubleshooting

FAQ

Frequently Asked Questions

• Q: Can children operate this appliance?
  • A: Children should not operate this appliance unsupervised. Ensure children are supervised and do not play with the appliance.
• Q: What should I do if I encounter difficulties during installation?
  • A: If you face any challenges during installation, refer to the instructions manual carefully or seek professional assistance.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>