STANLEY DR-1212 Timeit Outdoor Twin Mechanical Timer Instruction Manual

: June 1, 2024
: Stanley

Table of Contents

STANLEY DR-1212 Timeit Outdoor Twin Mechanical Timer
Product Usage Instructions
OPERATING INSTRUCTIONS
SPECIFICATIONS
Read User Manual Online (PDF format)
Download This Manual (PDF format)

STANLEY DR-1212 Timeit Outdoor Twin Mechanical Timer

STANLEY-DR-1212-Timeit-Outdoor-Twin-Mechanical-Timer-
PRODUCT

Specifications :

2 Grounded Outlets and Plug
Rated : 125VAC/60Hz/8A/1000W Resistive, 8A/1000W Tungsten, 500VA Electronic Ballast, 1/2 HP Motor Load

Product Usage Instructions

Setting Up the Timer:

Locate the electrical outlet near the device you want to control.
Set the ON / TIMER switch to TIMER and plug the timer into the outlet.
Set the current time by aligning the arrowhead on top of the timer dial to the present time.
Determine the desired start and end times and push down all pins between those times. Pins down indicate ON, while pins up indicate OFF.

Using the Timer:

Plug your electrical device directly into the timer.
Ensure the electrical device is set to the ON position for the timer control to work.
Set the switch on the timer to the TIMER position for it to work.

Additional Features:

To use the Manual Always ON feature, switch the ON / TIMER switch to ON. Remember to switch it back to the TIMER position for proper timer function. In case of power failure, reset the time as indicated in step 3 above.

Initial Use:

Install the unit at least 5ft above ground level with the outlet receptacle facing downward. Plug-in lights or appliances into the outlets at the bottom.

FAQ

Why are pins pushed down by default?
- The timer pins are factory preset in the pushed-down (‘ON’) position for convenience. Pull pins up for ‘OFF’ intervals.

OPERATING INSTRUCTIONS

Locate the electrical outlet that is close to the device you want to control.
Set the ON / TIMER switch located next to the dial to the TIMER position. Plug the timer into the outlet.
Set the current time – turning clockwise, align the Arrowhead (See diagram) on TOP of the timer to the present time (lines between numbers are in increments of 30 minutes). There is no need to touch the pins to set the current time.
- NOTE : Dial is based on AM/PM.
Determine the desired start time and push “DOWN” all pins until the desired OFF time. When pins are pushed down the timer will be on and working. When pins are in the UP position timer is OFF.
- NOTE : “pins” are grey slices around the dial. For example: to turn the timer ON at 5 pm and OFF at 10 pm, push down all the pins from 5 pm to 10 pm.
Plug your electrical device directly into the timer. The electrical device must be set to the “ON” position for the timer control to work properly.
The switch on the timer must be set to the TIMER position for the timer to work. To use the Manual “Always ON” feature, switch the ON / TIMER switch (located next to the dial) to ON for “Always ON”
- Be sure to set switch back to the TIMER position for proper timer function. In case of power failure, reset the time of day as indicated in step 3 above.

SPECIFICATIONS

Grounded Outlets and Plug Rated:

125VAC/60Hz/8A/1000W Resistive
8A/1000W Tungsten
500VA Electronic Ballast
1/2 HP Motor Load

INITIAL USE:

Install the cord and unit at least 5ft (1.5m) above ground level with the outlet receptacle facing downward. Let the switch hang downward so moisture doesn’t accumulate in the outlet. Plug the lights or appliances into the outlets at the bottom.

WARNING

DO NOT PLUG THIS TIMER INTO AN EXTENSION CORD OR OTHER ELECTRICAL ADAPTER. PLUG DIRECTLY INTO AN ELECTRICAL OUTLET.
DO NOT CONNECT THIS TIMER TO APPLIANCES THAT CONTAIN HEATING ELEMENTS (COOKING APPLIANCES, HEATERS, IRONS, ETC.). FAILURE OF THE TIMER TO SHUT OFF SUCH DEVICES MAY LEAD TO OVERHEATING AND A POTENTIAL FIRE.
DO NOT PLUG IN THIS TIMER IF IT IS WET.
DO NOT CLEAN THIS TIMER WHEN IT IS PLUGGED IN.
DO NOT EXCEED THE MAXIMUM RATINGS OF THE TIMER.
POTENTIAL SHOCK HAZARD: KEEP OUT OF REACH OF CHILDREN.

THREE-YEAR LIMITED WARRANTY

If within the first year from the date of purchase, this unit fails due to a defect, exchange where purchased, or ship it prepaid with proof of purchase to The NCC, 1840 McDonald Avenue, Brooklyn, New York 11223. Units that fail to operate during the second or third year from date of purchase must be shipped prepaid with proof of purchase to The NCC. We will replace the unit. This guarantee excludes normal wear and tear and damage resulting from accident, alteration, or misuse. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. For warranty replacement unit must be purchased from an authorized reseller.