behringer ULTRA-DI DI400P High Performance Passive DI Box User Manual

: June 1, 2024
: Behringer

Table of Contents

behringer ULTRA-DI DI400P High Performance Passive DI Box
Safety Instruction
1. Control Elements and Connections
2. Connecting an Instrument Signal
3. Limited Warranty
4. Specifications
FAQ (Frequently Asked Questions):
Documents / Resources

behringer ULTRA-DI DI400P High Performance Passive DI Box

behringer ULTRA-DI DI400P High Performance Passive DI
Box

USER MANUAL

ULTRA-DI DI400P

High-Performance Passive DI Box

Safety Instruction

1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9. Use only attachments/accessories specified by the manufacturer.

10. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

11. Correct disposal of this product: This symbol indicates that this product must not be disposed of with household waste, according to the WEEE Directive (2012/19/EU) and your national law. This product should be taken to a collection center licensed for the recycling of waste electrical and electronic equipment (EEE). The mishandling of this type of waste could have a possible negative impact on the environment and human health due to potentially hazardous substances that are generally associated with EEE. At the same time, your cooperation in the correct disposal of this product will contribute to the efficient use of natural resources.

For more information about where you can take your waste equipment for recycling, please contact your local city office, or your household waste collection service.

12. Do not install in a confined space, such as a book case or similar unit.
13. Do not place naked flame sources, such as lighted candles, on the apparatus.

1. Control Elements and Connections

Connections

(1) + (2) PARALLEL IN/OUT (¼” TS): These connectors are used for connecting unbalanced signal sources. Because both connectors are wired in parallel, they can be used both as an input and as a direct output to loop the signal through to a monitor amplifier.

(3) OUTPUT (XLR): This is the balanced mic-level output.

Use a high-quality balanced microphone cable to establish connection.

(4) Using the GND LIFT (ground lift) switch, you can fully separate input and output grounding. Depending on how the equipment to which your DI400P is connected is grounded, using the GND LIFT switch lets you lower hum noise or ground loops. When the GND LIFT switch is in LIFT position, the ground connection is interrupted.

The SERIAL NUMBER of the DI400P is located at the bottom.

2. Connecting an Instrument Signal

Signal

This illustration shows the application of a DI-box. The signal feeding the amplifier remains unchanged; it is simply taken and routed into the amp. The low-impedance balanced signal is forwarded to the mic input of the mixing console. This application has its advantages particularly with bass guitars, because very few microphones can linearly transmit bass frequencies with high signal levels. If you are using effects, insert the DI400P after the effects device, so that you can monitor the effects via the PA system or the recording as well.

3. Limited Warranty

For the applicable warranty terms and conditions and additional information regarding Music Tribe’s Limited Warranty, please see complete details online at community.musictribe.com/pages/support#warranty.

4. Specifications

Frequency response: 40 Hz (-3 dB) to 20 kHz
THD+N (distortion): 0.007% @ 1 kHz, input level +4 dBu
INPUT: ¼” TS (unbalanced)
Level change (Input Output) : 20 dB
OUTPUT: Balanced XLR
Impedance ratio (Input Output): 110 : 1
Dimensions (H x W x D): 2.6 x 4.7 x 1.4″ (H x W x D) 66 x 120 x 35 mm
Weight: approx. 0.44 lbs approx. 0.2 kg

Behringer continuously strives to assure the highest quality standards possible.
Required modifications may be implemented without prior notice. Technical data and the appearance of the unit may deviate from the above values and/or illustrations.

FAQ (Frequently Asked Questions):

Q: Can I use this DI box with a microphone?

A: Yes, you can use this DI box with a microphone to convert high-impedance signals to low-impedance signals for better audio quality.

Q: How do I connect the DI box to my audio interface?

A: Connect the output of your instrument or microphone to the input of the DI box using a suitable cable. Then, connect the DI box output to your audio interface using a balanced cable for optimal signal transfer.

Q: Can I use this DI box for recording electric guitars?

A: Yes, this DI box is suitable for recording electric guitars by providing impedance matching and noise reduction benefits.

We Hear You

Documents / Resources

| behringer ULTRA-DI DI400P High Performance Passive DI Box [pdf] User Manual
VD400-Vintage-Delay, RockBoard, ULTRA-DI DI400P High Performance Passive DI Box, ULTRA-DI DI400P, High Performance Passive DI Box, Performance Passive DI Box, Passive DI Box
---|---