PORTWELL WEBS-89I0 DIN Rail BoxPC with Intel Celeron User Manual
- June 1, 2024
- Portwell
Table of Contents
PORTWELL WEBS-89I0 DIN Rail BoxPC with Intel Celeron
Product Information
Specifications
- Model Name: WEBS-89I0
- CPU: 10W
- TDP: AMI UEFI
- BIOS: 256Mbit
- Memory: 1 x SO-DIMM DDR4-3200MHz, Support up to 32GB
- Storage: 1 x M.2-2242 M key SSD Slot SATA3.0
- USB: 3 x USB3.1
- COM: 1 x RS-232, 1 x RS-485
- Ethernet: 3x RJ45 GbE (Intel i210AT)
- Display: Support up to 4096 x 2160 @60Hz (DP), Support up to 3840 x 2160 @60Hz (HDMI)
Frequently Asked Questions
- Q: Are additional accessories required for setting up the WEBS-89I0?
- A: The necessary accessories are included with the product. However, for specific configurations or expansions, additional components may be needed.
- Q: What is the maximum display resolution supported by the WEBS-89I0?
- A: The device supports up to 4096 x 2160 resolution at 60Hz for DP and up to 3840 x 2160 resolution at 60Hz for HDMI.
- Q: How should I handle loose wiring or unstable communication issues?
- A: Ensure proper connection of terminals as per the provided parameters to prevent loose wiring or communication instability.
Quick Guide for WEBS-89I0
You will find the specifications, interface definition and how to use the
product from this quick guide. Please read and learn this guide carefully
before power on, for the I/O development Kit, please contact sales or local
reseller.
Please keep this guide properly for future reference and be sure to share for
the end user.
Safety Precautions
- Please read and follow the safety precautions before you are going to use it.
- Pay attention to the labels on the product.
- The“Tips”, ”Warnings”and“Danger”items in the following table don’t represent all safety precautions to be followed, but only the supplementary.
- Make sure to use in an environment that meets the design specifications, otherwise, malfunction or partial damage caused by non-compliance with relevant regulations is not covered under the product quality guarantee.
- Please unplug the power cord and do not use liquids to clean the PC.
- Please keep the PC in a safe space to prevent it from falling and damaging its components.
- Please keep the power cord in a safe location to avoid causing personal injury.
- Please do not bundle control wires, communication cables and power wires together, it would be better to keep a distance of at least 100mm between them to avoid mutual interference.
- It is recommended to use wires with isolation, especially in environments with severe electromagnetic interference.
- Please disconnect it from the power socket if the PC is not used for a long time.
- Please make sure that no liquids enter the device to avoid the risk of fire or short circuit.
- Please disconnect the power cord before opening the computer case.
- Please clean the dust regularly.
- Please ask for technical support and return the PC to RMA:
- The power cord or plug is damaged;
- Liquid has entered the interior of the PC;
- PC doesn’t work;
- PC is damaged;
- Physical damage on the PC
Safety Instructions
Symbols / Description
- Warning: There are potentially dangerous situations that If not avoided will result in death, serious injury or significant property damage.
- Danger: There are imminently dangerous situation that If not avoided will result in death, serious injury or significant property damage.
- Tip: There are important information tips.
Specification
| Model Name | WEBS-89I0 |
|---|---|
| CPU | Intel ®Celeron J6412,2.0-2.6GHz, |
4 Cores,4 Threads，1.5MB L2 Cache
TDP| 10W
BIOS| AMI UEFI 256Mbit
Memory| 1 x SO-DIMM DDR4-3200MHz,
Support up to 32GB
Storage| 1 x M.2-2242 M key SSD Slot，
SATA3.0
USB| 3 x USB3.1
COM| 1 x RS-232, 1 x RS-485
Ethernet| 3x RJ45 GbE (Intel i210AT)
DP| Support up to 4096 x 2160 @60Hz
HDMI| Support up to 3840 x 2160 @60Hz
Expansions| 1x Full-size miniPCIe slot
1 x SIM card holder on bottom side for easy access
DO| 1 x Programmable LED
Watch Dog| 1~255 levels programmable
Voltage Input| DC12~24V ±10%，overcurrent, overvoltage and polarity inverse
protection
Voltage Input Power Consumption| DC12~24V ±10%，overcurrent, overvoltage and polarity inverse protection
Max.60W
Dimensions| (L)138mm x (W)102mm x (H)48mm
Net Weight| 1.06Kg
Work Temperature| -20℃ ~ 60℃ (-4°F~40°F)
Stroage Temperature| -40℃ ~ 80℃ (-40°F~176°F)
Relative Humidity| 5~95%(Non-condensing)
Operating Vibration| 5~500Hz,1.5Grms@with SSD,Follow IEC60068-2-64
Operating Shock| 20G peak acceleration(11ms duration)with SSD,
Follw IEC60068-2-27
EMC| CE/FCC Class B
Interface specifications
No. / Definition
- Status LED
- Power button
- HDMI
- DP
- USB
- LAN
- Power connector
- COM
Interface description
Dimension
Connection And Use
Phoenix terminal wiring
The power input interface and serial communication interface of WEBS-89I0 adopt spring-type pressing terminals. Please connect according to the parameters in the table when using, otherwise it may lead to loose wiring, falling off or unstable communication.
Ethernet
- WEBS-89I0 have 3 Ethernet ports, standard RJ-45 connector.
- The network cable is recommended to use a shielded network cable of Category 5 or above to ensure its working stability.
RS-485 communications
The WEBS-89I0 have 1 channel of RS-485 with phoenix terminal. The cable is recommended\ to use a shielded twisted pair and the shield should be connected to the ground properly by the single point. A120 ohm terminal resistor should be placed at the end of the cable for limiting bus reflections.
Power supply
- In order to make the IPC work more reliably, it is recommended to add a DC power filter between the IPC and the input power supply, and ensure that the filter and the IPC must be well grounded to prevent some interference problems.
Memory card installation
WARNING: If the IPC is equipped with a SIM card, please remove the SIM card firstly, and then disassemble other parts.
Use a hexagonal screwdriver to remove the four screws (position 1-4 in Figure 1), open the rear case (position 5 in Figure 1), and insert the memory card into the slot(position 6in Figure 1) at an angle of 30°, then press it in the direction of the arrow (Figure 1) until the card audibly latches into place. Lift up in the direction of the arrow (Figure 2) to remove the memory.
4G / WiFi card installation
Use a hexagonal screwdriver to remove the four screws (position 1-4 in Figure 1), open the rear case (position 5 in Figure 1), and insert the expansion card into the slot (position 6 in Figure 1) at an angle of 30°, then press the expansion card in the direction of the arrow (Figure 1), and fix it on the motherboard with a M2 screw, the antenna adapter cable is installed at position A (Figure 2), and the other end is installed at position B (Figure 2). After the card and cable are installed, the rear cover of the machine can be closed, and the external antenna and SIM card can be installed after locking all of the screws.
Warning
- If the IPC is equipped with a SIM card, please remove the SIM card firstly, and then disassemble other parts.
SIM card installation
- WEBS-89I0 have a SIM card slot, and the SIM card can be installed and removed normally without dismantling the machine.
- When installing, push the SIM card into the card slot. And press the SIM card with a tool and the card will pop out when disassembling.
Tip
- Please pay attention to the direction of the SIM card when installing the SIM card, otherwise, the SIM card will not be recognized.
IPC installation
- WEBS-89I0 support wall mounted in default, and DIN-rail mounted is an option.
Ground wiring
- WEBS-89I0 have a ground screw on the side of the power terminal, it is recommended to use thicker and shorter cable to connect to the ground nearby properly.
IPC installation
In order to facilitate the installation and heat dissipation and ventilation
of the IPC, a sufficient distance should be left between the IPC and the
surrounding components.
Figures of two installation methods:
Wall mounted installation
There is a hanging plate on the back of the IPC, and there is a hole on the upper and lower sides of the hanging plate. The IPC can be fixed on the backboard through screws to realize the wall-mounted structure(Refer to Figure 1). Please refer to Figure 2 during disassembly. Please pay attention that the mounting screw pan head needs to be less than 8mm and greater than 4.5mm, screw length not less than 8mm.
DIN-Rail mounted installation
WEBS-89I0 also support DIN-Rail mounted as an option. Put the IPC in the normal mounting position, the IPC is mounted on the DIN rail from above. Make sure that the universal DIN rail adapter is in the correct position behind the DIN rail (A in Figure 1). Then press the IPC down until the universal DIN rail adapter audibly latches into place (B in Figure 1). Please make sure that the IPC is securely attached to the DIN rail. When disassembling, the steps are reversed, please refer to Figure 2 and Figure 3.
Copyright © Portwell, Inc., 2023. All rights reserved.
All other brand names are registered trademarks of their respective owners.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>