Portwell WEBS-21J0 Fan less Embedded System User Manual

Portwell WEBS-21J0 Fan less Embedded System

Product Information

Specifications

• Model: WEBS-21J0
• Type: Fan-less Embedded System
• Version: 1.0

Chapter 1: System Overview
This chapter provides an introduction to the product and includes the following sections:

• 1.1 Introduction
• 1.2 Check List
• 1.3 Product Specification
• 1.4 Mechanical Dimension

Chapter 2: System Installation
This chapter explains the installation process of the system and includes the following sections:

• 2.5.1 45 Degree Angle View (Standard)
• 2.5.2 Front View (Optional Kit: Additional 2x USB 3.0)
• 2.5.3 Rear View

Chapter 3: BIOS Setup Information
This chapter provides information on BIOS setup and includes the following sections:

• 3.1 Entering Setup
• 3.2 Main
• 3.3 Configuration

Chapter 4: Important Instructions
This chapter includes important instructions regarding warranty, liability, and conformity.

• 4.1 Note on the Warranty
• 4.2 Exclusion of Accident Liability Obligation
• 4.3 Liability Limitations / Exemption from the Warranty Obligation
• 4.4 Declaration of Conformity

Chapter 5: Frequently Asked Questions (FAQ)
This chapter provides answers to commonly asked questions about the product.

FAQ

• How can I configure the system to meet my operating requirements?
• Please refer to Chapter 1 for an overview of the product specifications and basic system architecture. Then, follow the instructions in Chapter 2 for system installation.
• What is included in the box?
• Please refer to Chapter 1, section 1.2 for the check list of items included in the box.
• How do I enter the BIOS setup?
• Please refer to Chapter 3, section 3.1 for instructions on entering the BIOS setup.

Preface

How to Use This Manual

• The manual describes how to configure WEBS-21J0 system to meet various operating requirements. It is divided into five chapters, with each chapter addressing a basic concept and operation of Fan-less Embedded System.
• Chapter 1: System Overview. Present what may have in the box and give an overview of the product specifications and basic system architecture for this fan-less embedded system.
• Chapter 2: System Installation. Show the definitions and locations of all the interfaces and describe a proper installation guide so that can easily configure the system.
• Chapter 3: BIOS Setup Information. Specify the meaning of each setup parameters, how to get advanced BIOS performance and update new BIOS. In addition, POST checkpoint list will give users some guidelines of troubleshooting.
• Chapter 4: Important Instructions. Indicate some instructions which must be carefully followed when the fan-less embedded system is used.
• C hapter 5: Frequent Asked Questions. Provide the answers for the most frequently asked questions.
• The content of this manual is subject to change without prior notice. These changes will be incorporated in new editions of the document. The vendor may make supplement or change in the products described in this document at any time.
• CAUTION: Risk of explosion if the battery is replaced by an incorrect type

Chapter 1 System Overview

Introduction

• Portwell Inc., a world-leading innovator in the Industrial PC (IPC) market, announced WEBS-21J0, a fan-less intelligent embedded system featuring 15W SKUs of the Intel Atom® x7000E family SoC (codename Alder Lake N). Its rugged, compact design and high performance make the WEBS-21J0, a perfect solution for applications in harsh environment, such as Industrial Automation, Kiosk and Digital Signage.
• The new rugged WEBS-21J0 is equipped with the Portwell NANO-6064, a NANO-ITX embedded board based on the Intel Atom® x7000E family SoC product family. Processors available in this product family combine low power consumption with high processing power and improved performance compared to previous generation processor. The compact WEBS-21J0 embedded system also features DDR4 SO-DIMM up to 16GB supporting 3200 MT/s; Two Display Ports (DP/HDMI) on the rear I/O (HDMI: resolution up to 4096 x 2160, DP : resolution up to 4096 x 2304); Two USB 3.2 Gen 2 ports (10Gbps) and Two ethernet Ports on the rear I/O. one COM port for RS-232/422/485 selected by BIOS; one audio jack to support Line-out; and one SATA III port, one M.2 B key 2280 socket and one Micro-SD socket for storage.
• The rugged, fan-less design makes the WEBS-21J0 durable in harsh environment applications, such as factory automation and industrial automation. The rugged and compact WEBS-21J0 supports a temperature range from 0ºC to 50ºC for harsh environment operations, while at the same time, its fan-less design ensures silent operation, reliability and low maintenance rate and costs. In addition, it has already passed a vibration test of 3Grms/ 10~500Hz and a shock test of 50G, assuring its solidity and reliability. In addition, the system accepts 12V input voltage.
• With its superior processing power, high capability, and support for 4K resolution (4096 x 2160), Portwell’s WEBS-21J0 is indeed an ideal solution for high computing power and/or high 3D video/image applications.

Check List

• The WEBS-21J0 package should cover the following basic items:
  • One WEBS-21J0 Fan-less Embedded System
  • One 65W AC/DC Power Adapter DC-plug with screw (Optional)
  • Other Accessories
• If any of these items is damaged or missing, please contact your vendor and keep all packing materials for future replacement and maintenance.

Product Specification

• System

  • M/B NANO-6064

  • CPU

  • Intel Atom® x7000E Series Processor

  • Intel® Core i3 N- Series Processor

  • BIOS AMI uEFI BIOS (SPI ROM)

  • System Memory DDR4 3200 MT/s Non-ECC SO-DIMM up to 16GB

  • Storage 1x SATA III port 1x mSATA socket (Choose either mSATA or mini-PCIe by BIOS)

  • Watchdog Timer Programmable by embedded controller

  • H/W Status Monitor System monitor (Voltage and Temperature)
    Expansion

  • 1x M.2 E Key 2230

  • 1x M.2 B Key 3052+2280 (Share with M.2 2280 SATA III socket)

• External I/O

  • Series Ports 1x RS-232/422/485 COM Port (selected by BIOS)
  • Display
  • 1x HDMI (HDMI 2.0b,4096×2160@60Hz)
  • 1x DP, (DP 1.4,4096×2160@60Hz)
  • USB 2x USB 3.2 Gen 2(Optional kit: additional 2x USB 3.2)
  • Audio Audio Jack with Line-out with Realtek AC897 Audio controller
  • LAN 2x Intel ® 2.5GbE Ethernet control (I225-LM)
  • Other TPM 2.0 on board

• Power Supply Unit

  • Power Supply DC 12V

• Environment

  • Operating Temperature 0℃ to 50℃
  • Storage Temperature -40℃ to 85℃
  • Relative Humidity 95% @ 40℃, non-condensing
  • Operating Vibration
  • System: 3Grms/10~500Hz, IEC 60068-2-6
  • Wall mount: 3Grms/10~500Hz, IEC 60068-2-6
  • Din Rail: 3Grms/10~500Hz, IEC 60068-2-6
  • Operating Shock
  • System: 50G, 11 msec, IEC 60068-2-27
  • Wall mount: 15G, 11 msec, IEC 60068-2-27
  • Din Rail : 15G, 11 msec, IEC 60068-2-27

• Mechanical

  • Dimension (WxDxH) 150x 150 x 66 mm
  • Weight 1.4 kg
  • Mounting Wall, DIN Rail mounting

Mechanical Dimension

• Front view of the WEBS-21J0 system (standard

• Front view of the WEBS-21J0 system (with optional kit: addition 2x USB 3.0)

• Front view of the WEBS-21J0 system (with optional kit: DIN-Rail mounting)

• Rear view of the WEBS-21J0 system

• Side view of the WEBS-21J0 system

• Top view of the WEBS-21J0 system

Chapter 2 System Installation

This chapter provides you with instructions to set up your system. Definitions and locations of all the interfaces are described so that you can easily configure your system. For more detailed PIN assignment and jumper setting, please refer to user’s manual of NANO-6064.

Storage M.2 2280 Device Installation
It’s easy to install and maintenance the 1x M.2 2280 module by just open the back cover.

• Step 1. Loosen the 4 screws of the back cover
• Step 2. Take out the back cover

• Step 3. Assemble the M.2 2280 module and make sure it has been screwed
• Step 4. Tighten the 4 screws of the back cover

M.2 Key E 2230 Device Installation
It’s easy to install and maintenance the 1x M.2 2230 device by just open the back cover.

• Step 1. Loosen the 4 screws of the back cover
• Step 2. Take out the back cover

• Step 3. Assemble the Half-size Mini-PCIe card and make sure it has been screwed
• Step 4. Install the SMA cable onto main connector of module

• Step 5. Put the Antenna cable through the antenna hole
• Step 6. Install the Antenna

• Step 7. Position the back cover
• Step 8. Tighten the 4 screws of the back cover

DIN Rail Mounting Device Installation
It’s easy to install and maintenance the Din Rail mounting device by just open the back cover.

• Step 1. Loosen the 4 screws of the back cover
• Step 2. Take out the back cover

• Step 3. Take out the front side cover and prepare Din rail mounting side cover
• Step 4. Position the back cover

• Step 5. Tighten the 4 screws of the back cover
• Step 6. Final Photo

Getting Started
It is easy to get the system started.

• Step 1. Make sure the power supply (12V) is connected properly
• Step 2. Press the power button to turn on the system

I/O Interfaces

1. **45 Degree Angle View (Standard)

**

2. **Front View (Optional Kit: Additional 2x USB 3.0)

**

3. **Rear View

**

• DC in: (12V)
  Using the provided DC source to connect to the system.

• Power Button:
  Press the power button to turn ON/OFF the system.

• SSD LED:
  Shows real-time read and write activity of your SSD as a small blinking indicator.

• DP / HDMI:
  DP /HDMI (Display Port) display output

• LAN:
  2x Intel ® 2.5GbE Ethernet control (I225-LM)

• USB 3.2:
  Two USB 3.2 Gen2 (Universal Serial Bus) port. (Optional Kit: Additional 2x USB 3.2)

• RS-232/422/485:
  *Note: RS-232/422/485 configuration is determined by BIOS setting. Check BIOS setting for details.

• Audio:
  Audio Jack with Line-out with Realtek ALC897 audio controller.

• Antenna Hole:
  Antenna holes for wireless module to usage.

Chapter 3 BIOS Setup Information

WEBS-21J0 system adopts NANO-6064 mother board. The following section describes the BIOS setup program. The BIOS setup program can be used to view and change the BIOS settings for the module. Only experienced users should change the default BIOS settings.

Entering Setup
Power on the computer and the system will start POST (Power on Self Test) process. When the message below appears on the screen, press key will enter BIOS setup screen.

• Press to enter SETUP
  If the message disappears before responding and still wish to enter Setup, please restart the system by turning it OFF and On or pressing the RESET button. It can be also restarted by pressing , , and keys on keyboard simultaneously.

• Press to Run General Help or Resume
  The BIOS setup program provides a General Help screen. The menu can be easily called up from any menu by pressing . The Help screen lists all the possible keys to use and the selections for the highlighted item. Press to exit the Help Screen.

Main
Use this menu for basic system configurations, such as time, date etc.

Detailed System Information

Configuration

1. **CPU Configuration

**

2. **Chipset Configuration

**

3. **Graphics Configuration

**

4. **eDP-to-LVDS configuration

**

5. **OEM Profile: PANEL 1 Configuration

**

6. **Power Control Configuration

**

7. **PCI/PCIE Configuration

PCI Express Root Port 7, 9, 10

**

8. **LAN Configuration

**

9. **SATA Configuration

**

10. **USB Configuration

**

11. **TPM Configuration: TPM 2.0 Device Found

**

12. **Super IO Configuration

**

13. **HW Monitor

**

14. **Serial Port Console Redirection

COM0 Console Redirection Settings:

**

15. **EC Firmware Update

**

  *  **Select file

**

  *  **Update

**

  * ![Portwell WEBS-21J0 Fan less Embedded System-fig-57](https://manuals.plus/wp-content/uploads/2023/12/Portwell-WEBS-21J0-Fan-less-Embedded-System-fig-57.png)

Security

• **Secure Boot

**

• **Key Management

**

Boot

UEFI Application Boot Priorities:

Save & Exit

NANO-6064 BIOS / EC UEFI Update SOP process under UEFI Shell

• Step1. Prepare a USB DOK.
• Step 2. Unzip BIOS update file to the USB DOK.
• Step 3. Plug the USB DOK into the target system and then boot in UEFI Shell by selecting UEFI: Built-in EFI Shell in the BIOS Save & Exit page.

• Step 4. Under the UEFI shell, direct to your USB DOK, below picture is an example using fs0. Then direct to the folder with BIOS / EC updated file and then enter command: “Update.efi” to start updating BIOS / EC.

• Step 5. The updating process will start and you can see the updating progress. When you see the following pictures, which means the BIOS / EC update processes finished. Please cut the AC power off and wait for 10 seconds before powering on.

Chapter 4 Important Instructions

This chapter includes instructions which must be carefully followed when the fan-less embedded system is used.

Note on the Warranty
Due to their limited-service life, parts which, by their nature, are especially subject to wear are not included in the guarantee beyond the legal stipulations.

Exclusion of Accident Liability Obligation
Portwell, Inc. shall be exempt from the statutory accident liability obligation if users fail to abide by the safety instructions.

Liability Limitations / Exemption from the Warranty Obligation
In the event of damage to the system unit caused by failure to abide by the hints in this manual and on the unit (especially the safety instructions), Portwell, Inc. shall not be required to respect the warranty even during the warranty period and shall be free from the statutory accident liability obligation.

Declaration of Conformity

EMC
CE/FCC Class A
This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This equipment may not cause harmful interference.
2. This equipment must accept any interference that may cause undesired operation.

Chapter 5 Frequent asked question

• I forgot my password of system BIOS, what am I supposed to do?
  You can switch off your power supply then find the JP3 on the NANO-6064 board to set it from 2-3 n/a to 1-2 short and wait 5 seconds to clean your password then set it back to 2-3 short to switch on your power supply.

• Portwell Software Service?

1. If you have customized requirements of BIOS, you can contact person of our company or branch.
2. If you have requirements of WDT、GPIO APP, you can contact our headquarter or branch, and we can render your assistance on developing.

Portwell Worldwide:

• Portwell, Inc.
  E-mail: info@portwell.com.tw

• Shanghai Portwell
  E-mail: info@portwell.com.cn

• Portwell Japan, Inc
  E-mail: info@portwell.co.jp

• American Portwell Technology
  E-mail: info@portwell.com

• European Portwell Technology
  E-mail: info@portwell.eu

• Portwell UK Ltd.
  E-mail: info@portwell.eu

• Portwell Deutschland GmbH
  E-mail: info@portwell.eu

• Portwell India Technology
  E-mail: info@portwell.in

• Portwell Korea, Inc.
  E-mail: info@portwell.co.kr

References

• ポートウェルジャパン株式会社 | 産業用PC, IoT, エッジコンピューティング端末メーカー
• 산업용보드, 산업용컴퓨터 | Portwell Korea | 대한민국
• Portwell -  Home
• Portwell, Inc. - Together in Electric Dream!
• Portwell - Industrial PC Manufacturer, Industrial Computer Systems
• Portwell -  Portwell Deutschland GmbH
• Portwell -  Home
• Embedded System Manufacturer | Industrial PC | Box-PC - Portwell India

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>