behringer Four Play Quad Voltage Amp and Mixer User Guide

behringer Four Play Quad Voltage Amp and Mixer

Product Information

• Specifications:
  • Model: FOUR PLAY V3.0
  • Controls: CV IN, CV ATTENUATOR, BOOST, CURVE, LEVEL, INPUTS, OUTPUTS
  • Power Supply: +12V / -12V

Product Usage Instructions

• Safety Instructions:
  • Before using the FOUR PLAY module, please ensure to follow these safety guidelines:
  • Read and follow all instructions provided in the user manual.
  • Avoid contact with water, except for outdoor use.
  • Clean the module only with a dry cloth.
  • Do not block any ventilation openings on the module.
  • Install the module according to the manufacturer’s instructions.
  • Avoid placing the module near heat sources such as radiators or amplifiers that produce heat.
  • Use only attachments and accessories specified by the manufacturer.
• Power Connection:
  • To connect power to the FOUR PLAY module, follow these steps:
  • Make sure the power supply or rack case power is turned off and disconnect the power cable.
  • Insert the 16-pin connector on the power cable into the socket on the power supply or rack case with proper alignment.
  • Insert the 10-pin connector into the socket on the back of the module ensuring correct orientation.
• Controls:
  • The FOUR PLAY module features various controls for sound manipulation:
  • CV IN: Control voltage input for channels 1-4, adjust using the knob.
  • CV ATTENUATOR: Attenuates control voltage signals.
  • BOOST: Adjusts the signal boost with a range of +6 dB.
  • CURVE: Controls the curve shape of the signal.
  • LEVEL: Adjusts the overall output level.
  • INPUTS: Input jacks for connecting audio sources.
  • OUTPUTS: Output jacks for routing audio signals including a mix output for all four channels.

FAQs

• Q: How do I clean the FOUR PLAY module?
  • A: Use a dry cloth to gently clean the module’s surface. Avoid using any liquids or cleaning agents.
• Q: Can I use any power cable to connect the module?
  • A: No, use only the provided power cable to connect the FOUR PLAY module to ensure compatibility and safety.

Safety Instruction

1. Please read and follow all instructions.
2. Keep the apparatus away from water, except for outdoor products.
3. Clean only with a dry cloth.
4. Do not block any ventilation openings. Install per the manufacturer’s instructions.
5. Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including amplifiers) that produce heat.
6. Use only attachments/accessories specified by the manufacturer.
7. Use only specified carts, stands, tripods, brackets, or tables. Use caution to prevent tip-overs when moving the cart/ apparatus combination.
8. Avoid installing in confined spaces like bookcases.
9. Do not place near naked flame sources, such as lighted candles.
10. Operating temperature range 5° to 45°C (41° to 113°F).

LEGAL DISCLAIMER

• Music Tribe accepts no liability for any loss that may be suffered by any person who relies either wholly or in part upon any description, photograph, or statement contained herein.
• Technical specifications, appearances and other information are subject to change without notice.
• All trademarks are the property of their respective owners. Midas, Klark Teknik, Lab Gruppen, Lake, Tannoy, Turbosound, TC Electronic, TC Helicon, Behringer, Bugera, Aston Microphones and Coolaudioare trademarks or registered trademarks of Music Tribe Global Brands Ltd.
• © Music Tribe Global Brands Ltd. 2024 All rights reserved.

LIMITED WARRANTY

• For the applicable warranty terms and conditions and additional information regarding Music Tribe’s Limited Warranty, please see complete details online at community. musictribe.com/support.

FOURPLAY CONTROLS

Controls

1. CV IN – Each channel has its CV input which is cascaded to the channels below, provided that they do not have a CV cable inserted. If only CV IN 1 is connected it will control all 4 channels. Each CV input has an associated CV LED which lights green for a positive CV (VCA gain) and red for a negative CV (VCA attenuation), if the CV IN voltage is 0V then the LED does not light.
2. CV ATTENUATOR – Each channel has a CV Attenuator, which can reduce the CV input signal level when moved CCW.
3. BOOST – Each channel has a switchable Boost control, which raises the input gain by +6 dB when the switch is set in the right-hand position.
4. CURVE – Each channel has a continuously variable VCA response curve, ranging from exponential at full CCW to linear at full CW.
5. LEVEL – Each channel has its own overall VCA output level control. The response of the Level control is affected by the Curve control setting.
6. INPUTS – Each channel has its input, which can be used with audio or CV input signals.
7. OUTPUTS – Each channel has its output, which is mixed with channels to the right if no output cable is inserted into that channel output. If only the 4/ Mix output jack is connected the module operates as a 4 into 1 mixer, which can be operated manually using the Level controls, or voltage controlled via the CV inputs.

Power Connection

The FOUR PLAY module comes with the required power cable for connecting to a standard Eurorack power supply system. Follow these steps to connect power tothe module. It is easier to make these connections before the module has been mounted into a rack case.

1. Turn the power supply or rack case power off and disconnect the power cable.
2. Insert the 16-pin connector on the power cable into the socket on the power supply or rack case. The connector has a tab that will align with the gap in the socket, so it cannot be inserted incorrectly. If the power supply does not have a keyed socket, be sure to orient pin 1 (-12 V) with the red stripe on the cable.
3. Insert the 10-pin connector into the socket on the back of the module. The connector has a tab that will align with the socket for correct orientation.
4. After both ends of the power cable have been securely attached, you may mount the module in a case and turn on the power supply.

Installation

• The necessary screws are included with the module for mounting in a Eurorack case.
• Connect the power cable before mounting.
• Depending on the rack case, there may be a series of fixed holes spaced 2 HP apart along the length of the case, or a track that allows individual threaded plates to slide along the length of the case.
• The free-moving threaded plates allow precise positioning of the module, but each plate should be positioned in the approximate relation to the mounting holes in your module before attaching the screws.
• Hold the module against the Eurorack rails so that each of the mounting holes is aligned with a threaded rail or threaded plate.
• Attach thescrews part way to start, which will allow small adjustments to the positioning while you get them all aligned.
• After the final position has been established, tighten the screws down.

Specifications

Inputs

• CV in
  • Type 4 x 3.5 mm TS jacks, DC coupled
  • Impedance > 1 MΩ, unbalanced, half normalled
  • Max input level 10 V p-p
• In
  • Type 4 x 3.5 mm TS jack, DC coupled
  • Impedance 30 kΩ, 15 kΩ with boost enabled, unbalanced
  • Max input level +19 dBu

Outputs

• Out
  • Type 4 x 3.5 mm TS jack, DC coupled
  • Impedance 100 Ω, unbalanced, half normalled
  • Max output level +19 dBu
  • Output noise at unity gain -92 dBu, 22 Hz-22 kHz
  • Output noise at full attenuation -98 dBu, 22 Hz-22 kHz
  • Maximum attenuation -97 dB at 1 kHz

Controls

• CV attenuator -∞ to unity gain
• Exp/Lin Exponential to linear CV response
• Level -∞ to unity gain
• Boost switch Adds +6 dB input gain
• CV LED
  • Green = positive CV,
  • Red = negative CV

Power

• Power supply Eurorack
• Current draw 100 mA (+12 V), 100 mA (-12 V)

Physical

• Dimensions 60.6 x 129 x 41.3 mm (2.39 x 5.08 x 1.63″)
• Rack units 12 HP
• Weight 0.14 kg (0.31 lbs)

FCC

FEDERAL COMMUNICATIONS COMMISSION COMPLIANCE INFORMATION

• Responsible Party Name: Music Tribe Commercial NV Inc.
• Address: 122 E. 42nd St.1, 8th Floor NY, NY 10168, United States
• Email Address: legal@musictribe.com.

FOURPLAY
This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
  • This equipment complies with Part 15 of the FCC rules.

Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Important information: Changes or modifications to the equipment not expressly approved by Music Tribe can void the user’s authority to use the equipment.

• Hereby, Music Tribe declares that this product is in
• compliance with Directive 2014/30/EU, Directive
• 2011/65/EU and Amendment 2015/863/EU, Directive
• 2012/19/EU, Regulation 519/2012 REACH SVHC and
• Directive 1907/2006/EC.
• Full text of EU DoC is available at https://community.musictribe.com/.
• EU Representative: Music Tribe Brands DK A/S
• Address: Gammel Strand 44, DK-1202
• København K, Denmark
• UK Representative: Music Tribe Brands UK Ltd.
• Address: 8th Floor, 20 Farringdon Street London EC4A 4AB,
• United Kingdom

Correct disposal of this product: This symbol indicates that this product must not be disposed of with household waste, according to the WEEE Directive (2012/19/ EU) and your national law. This product should be taken to a collection center licensed for the recycling of waste electrical and electronic equipment (EEE). The mishandling of this type of waste could have a possible negative impact on the environment and human health due to potentially hazardous substances that are generally associated with EEE. At the same time, your cooperation in the correct disposal of this product will contribute to the efficient use of natural resources. For more information about where you can take your waste equipment for recycling, please contact your local city office or your household waste collection service.

References

• Music Tribe
• Music Tribe
• Music Tribe

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>