SUPERATV Teryx4 S Deluxe Self Canceling Turn Signal Kit Instruction Manual

SUPERATV Teryx4 S Deluxe Self Canceling Turn Signal Kit

Product Information

• Specifications
  • Model: IN-TSK-K-TRX4S-007
  • Components: Horn, Mounting Bracket, M6 Nylock Nut, Signal Control Unit, Cable Ties, Signal Switch, Self Tap Screws, Dielectric Grease, Heat Shrink Splices, LED Signal Lights
  • Quantity: Horn (1pc), Mounting Bracket (1pc), M6 Nylock Nut (1pc), Signal Control Unit (1pc), Cable Ties (30pcs), Signal Switch (1pc), Self Tap Screws (3pcs), Dielectric Grease (1pc), Heat Shrink Splices (6pcs), LED Signal Lights (4pcs)

Product Usage Instructions

• Step 1: Preparation
  • Remove the passenger seat, centre console, and dash panel.
• Step 2: Routing Harness
  • Route the back half of the harness to the back of the vehicle. Then route the front half through the dash and pull wires to the front.
• Step 3: Mounting Components
  • Mount the control box and connect the harness. Drill holes and mount passenger’s side signal lights. Mount the horn and connect it to the harness. Drill holes and mount driver’s side signal lights.
• Step 4: Replacing Stock Harness
  • Unplug the stock harness and replace it with the new harness connections at designated places.
• Step 5: Final Installation
  • Mount the license plate light as desired. Install the horn and signal switches. Replace the dash panel, centre console, and seats.

FAQs

• Q: Do I need any special tools for installation?
  • A: Basic tools like screwdrivers, drills, and pliers are recommended for installation.
• Q: Can I install the kit without previous experience?
  • A: While some mechanical knowledge is helpful, the kit comes with detailed instructions to guide you through the installation process.
• Q: How do I ensure proper functioning after installation?
  • A: Test all components before finalizing the installation. Ensure connections are secure and wires are properly routed to avoid interference.

Discard Packaging

Do Not Discard Packaging Until the Product Has Been Successfully Installed

What You’ll Be Doing

• First, you will remove your passenger seat, Center Console and Dash Panel.
• Route the Front half of the harness through the dash and pull the wire through to the front.
• Mount the Control Box & connect the Harness.
• Drill two holes and mount the Passenger’s Side Signal Lights.
• Mount Horn & connect to Harness. Drill two holes and mount the Driver’s Side Signal Lights.
• Routing the back half of Harness to the back.
• Unplug the stock harness and replacing with New Harness Connections in a few places.
• Mount License Plate Light where desired.
• Then install the Horn and Signal Switches.
• Replace Dash Panel, Console and Seats.

Installation

1. The first things you want to do are remove the Dash Panel and remove the Centre Console. See Fig.1.
2. To remove the Center Console, release the Push-Pins around the console first, then remove it and set it out of the way.
3. Next, remove the Passenger Side Seat as we will be routing the harness cables along that side of the vehicle. See Fig.2.
4. Taking the main harness, we will start in the middle of the vehicle and first work forward towards the front to install the Control Unit, Horn and Front Signal Lights. So starting in about the middle of the harness, route the front half of it through the dash opening, following along the existing wiring harness on the Passenger’s side. We will then go around to the front to pull the harness to the locations we need from there. See Fig.3.
5. Next, go around to the front of the vehicle and pull the harness through the access area you fed it through from the dash. As you can see the harness splits into different groups. Some for the Right Signal, the Left Signal and Horn and the Control Unit. See Fig.4. These are explained in more detail in the coming steps.
6. Next, you will mount the Control Box onto the firewall using (2) #8×3/4″ Self Tapping Screws provided in your kit. Mount in the general area or location shown, and plug in the (2) connectors from your new cable harness. See Fig.5.
7. After the Control Box is mounted and plugged in from the harness, you can now run the Green & Black wire sets to the Passenger’s Side Front Wheel Well area to locate a desired location to drill and mount your lights. See Fig.6.
8. Fig.7 shows a typical location for the Front and Side turn signals. However, you can mount them in different places if you desire.
9. Use a 3/4″ dia. drill bit for the turn signal light gasket/fixtures to be pressed into. If they are hard to insert, you can separate the LED from the gasket as shown in Fig.8. Press the gasket into the hole first, then press the LED into the gasket.
10. After the passenger side is installed, now route the Yellow & Black and the Red & Black wire sets to the Driver’s Side as shown in Fig.9.
11. As you can see, the Yellow & Black wires are for your LED lights and are routed towards the wheel well for you to pick your desired locations and install them. See Fig.10.
12. Next, you will mount the horn and hook it up to the cable harness. Fig.9 as we saw shows the basic routing of where to place the horn and how the cables route. To mount the Horn, take out the Factory Screw shown in Fig.11 and place the Mounting Bracket (provided in your kit) underneath the plastic and reinstall the Factory Screw but leave it loose to adjust after Horn is installed. Then attach the Horn to the Mounting Bracket using the M6 Nylock Nut also provided in your kit and tighten down. Then position the horn as shown in Fig.11 and tighten down the Factory Screw to hold in place.
13. After the Horn is installed, now hook up the Red and Black wires from the harness to the tabs as shown in Fig.12. Fig.13 shows the Horn and wires installed and complete. Routing The Harness To The Back
14. To route the cable to the rear section of the vehicle, you will start at the midpoint or where you ran it through the firewall to the front, but will now run the rear part of the harness along the Passenger Console area as shown in Fig.14. To run it out the back, you will push the harness under the plastic flap and back which will allow it to exit the cabin and out under the back end of the vehicle.
    • Fig.15 shows the harness exiting the cabin and out the back, you can then pull it back to the location needed.
    • SHOP TIP: To get more access room to pull the harness through from the front, you can wedge a broom handle or similar between the Console and seat area to open it up a little more, making it easier to pull the harness through. See Fig.15.
15. After getting the harness through the Seat/Console path, pull it back a little and notice up on the frame you’ll see the original harness connector as shown in Fig.16. Now Unplug that connector and insert the Grey Male end of the next closest cable pair of your New Harness into the Female end of the same connector. These are shown plugged together in Fig.16. Then take the other end (or Male end of the original connector) and plug it into the Female end of the New Harness connector of that same cable pair. So in a Nutshell, you are unplugging the stock one, and replacing those ends with New plugs from your new harness.
16. Now, continuing from that point, route the remaining harness back up along the frame with the original harnessing as shown if Fig.17, and then route the remaining wires in the directions needed. The Black/Red/Green wire set will go to the Right Turn Signal as seen in Fig.17.
17. After routing to the Right Turn signal, see the Factory light connector, up under, and Unplug it. Then plug in the Black/Red/Green plug from your New Harness into the connector end of the factory Harness. See Fig.18. (You will not use the old connector end as shown. Tie off up out of the way)
18. The remaining Black/Red wire set that goes to the Driver’s Side is for the license plate light, which you can choose where to install. Tie up out securely of the way. See Fig.19. Installing Your New Switches
19. To install your new switches, we have chosen to install them into the stock factory dash panel, both Horn and Turn Signal switches. See Fig.20.
20. The last remaining wire sets for our installation are the “Red & Black” set which you will plug into your Horn Switch. And the “Multi-Colored” wire set you will plug into your Turn Signal Toggle Switch as shown in Fig.21. Then reinstall the Dash Panel, Console and Seats back to normal.

Switch Orientation

Switch Templates

Liability Statement

• SuperATV’s® products are designed to best fit user’s ATV/UTV under stock conditions. Adding, modifying, or fabricating any factory or aftermarket parts will void any warranty provided by SuperATV® and is not recommended. SuperATV’s® products could interfere with other aftermarket accessories.
• If the user has aftermarket products on the machine, contact SuperATV® to verify that they will work together.
• Although SuperATV® has thousands of satisfied customers, users should be aware that installing lift kits, long travel, suspension kits, tyres, etc. will change the ride of the machine and may increase maintenance and part wear. Operating any off-road machine while, or after, consuming alcohol and/or drugs increases the risk of bodily harm or death. No warranty or representation is made as to this product’s ability to protect users from severe injury or death. SuperATV® urges operators and occupants to wear a helmet and appropriate riding gear at all times.
• By purchasing and installing SuperATV® products, the user agrees that should damages occur, SuperATV® will not be held responsible for loss of time, use, labour fees, replacement parts, or freight charges. SuperATV®, nor any 3rd party, will not be held responsible for any direct, indirect, incidental, special, or consequential damages that result from any product purchased from SuperATV®. The total liability of the seller to the user for all damages, losses, and causes of action, if any, shall not exceed the total purchase price paid for the product that gave rise to the claim.
• SuperATV® will warranty only parts provided by SuperATV®. Any damage or problems with OEM housings, bearings, seals, or other manufacturers’ products will not be covered by SuperATV®. SuperATV® parts and products are not warranted if the item was not installed properly, misused, or modified.
• Installing, adding, modifying, or fabricating any factory or aftermarket product to your ATV/UTV may violate certain local, state, and federal laws. Be advised that laws vary depending on town, city, county, state, etc. Use of certain products on public streets, roads, or highways may violate law.
• The Buyer is solely and exclusively legally and personally responsible for any violation of the law by the installation or use of the product. You must abide by all local, state, and federal laws, including but not limited to vehicle safety, traffic laws, and ordinances. It is your responsibility to know the laws and how they apply to you.
• The Buyer is responsible for fully understanding the capability and limitations of his/her vehicle according to manufacturer specifications, warnings and instructions and agrees to hold SuperATV® harmless from any damage resulting from failure to adhere to such specifications, warnings and/ or instructions. The Buyer is also responsible to obey all applicable federal, state, and local laws and ordinances when operating his/her vehicle while using this product, and the Buyer agrees to hold SuperATV® harmless from any violation thereof.

If you have any problems/questions on this kit, contact us by email at Superatv.com.

Need help with your installation?

• sales@superatv.com.
• 1-855-743-3427
• www.superatv.com.
• 8:00am – 9:00pm EST M-Th
• 8:00am – 7:00pm EST Friday
• 9:00am – 2:00pm EST Saturday
• Like SuperATV on Facebook to keep up to date on new products!
• ©2023 Superatv.com. All Rights Reserved
• IN-TSK-K-TRX4S-007_7-5-23
• 2753 Michigan Road
• Madison, Indiana 47250 855-743-3427

References

• Superatv.com
• superatv.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>