AZIJYV G13 Digital Speedometer Instruction Manual
- June 1, 2024
- AZIJYV
Table of Contents
GPSspeedometer:G13
Kindly remind ：The standard working voltage is 5V. It is forbidden to use
power supply higher than 5V.
After power on, the satellite icon flashes to indicate the star search, the
GPS satellite icon stops flashing and shows more than 5 satellites before it
can be used normally
Description of the interface:
- Compass: The icon will stop flashing after the satellite is found, and then G13 can work normally (N-North/ E-East/ W-West/ S-South)
- Area 2：Speed/ Clock/ Speed+Clock/ Satellites number/ Driving distance/ Driving time (Press vertically to switch)
- Speed unit:MPH (miles) km/h (kilometer)
Description of the button
- Short press in(1s to release)：Freely switch between Speed/ Clock/ Speed+Clock/Number of satellites （Short press in to “Confirm” in Setting mode）
- Long press in(2s to release):Enter the settings menu, adjust the vertical long press 2 seconds to save the exit
- push left: switch compass color (adjust option after entering settings)
- Long push left: Long push left 2 seconds to hear Didi turn off buzzer alarm, again left dial 2 seconds to hear Didi turn on the buzzer
- short push right : switch the color of the multi-function area (adjust option after entering settings)
Setting Mode:
Long press in to enter the Setting mode, Short push right to switch the
Setting item, Short press in to confirmed, After adjustment, Long press 2
second in to save and exit.
Setting item
| Function| Adjustment Range| Description| Default|
Interface of setting
---|---|---|---|---|---
| Adjust speed| 50-150| Adjust the parameter value when there is an error
between HUD and dashboard.
Ex: dashboard displays 100 KM, HUD displays 105 KM. Please adjust the
parameter value to102.(107-5)| 107|
| Over-speed alarm setting| 0-250| Overspeed alarm is 150KM/H,users can freely
set this value| 150|
| Fatigue driving reminder| 1.0-8.0| Fatigue driving reminder is 8 hours| 8.0|
| Brightness adjustment| 0-11| 0-automatic photosensitive mode 1-11 is manual
adjustment| 0|
| Speed unit| 0-1| 0- KMH 1- MPH| 0|
| Time adjustment| 0:00-12:00| Please adjust the clock based on your GMT
timezone,up for GMT +,down for GMT – Default clock is Chinese GMT 8,HUD will
display the specific accurate time of GMT 8 after the star is found)| 8：00|
| Factory setting| 0-1| The default is 0, adjust to 1 and long press 2 second
in to save| 0|
FAQ
1.No display on the screen, No power
Please check whether the USB cable is damaged, or replace the USB cable test (note: it is forbidden to use a voltage higher than 5V for power supply)
2.No Speed
GPS blinks for searching numbers ongoing.Please move the car to wide road. It will work after GPS light steady.
3.The speed is still displayed after the car has stopped
If driving to underground parking lots, tunnels, under flyovers and other places that make the signal unstable, the data displayed by the product may have some deviation, drive the car to the open road to restore normal
4.Inaccurate Speed
a.Check whether the unit is correct, km KM/mile MPH, (please refer to Menu 5 to switch speed unit) b.Fine-tuning the vehicle speed, such as the meter displays 100 Km/h, the machine displays 105 Km/h, adjust the parameter value to 102.
5.Time adjustment
a.The default is Beijing8.00 time, China. b. If the Time to another Time zone is needed, please enter Setting item “6” in the Setting mode, and short push left/right to adjust the Time. The adjustment range is 30 minutes at a time.(For example, if a certain area is 1 hour faster than Beijing Time, short push right the button twice) Attention: The satellite icon flashing indicates that there is no satellite was found, Please adjust to the time zone of your country (e.g. Korea +9:00) after the satellite icon stops blinking, and then directly calibrate the displayed time.
6. Driving direction is wrong
Driving direction will go normal after the vehicle speed exceeds 5KM / H
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>