AML ACC-7715-PS Inline Charger User Guide

June 1, 2024
AML

AML ACC-7715-PS Inline Charger

AML-ACC-7715-PS-Inline-Charger-prodcut

Specifications

  • Power Supply Output: 12 VDC, 2.5A
  • Power Supply Certification: EN60950
  • Compatible Devices: M7700 Striker, M7800 Scepter, M7800 Solo Mobile Computer

Product Usage Instructions

Set Up

Unpacking the Charger
The shipping box includes:

  • One ACC-7715-PS Inline Charger
  • One PWR-8050US Power Supply (12 VDC, 2.5 A)
  • This User’s Guide

Connecting the Power

  1. Plug in the PWR-8050 power supply to a standard 120 VAC electrical outlet.
  2. Connect the plug on the end of the power supply to the round, barrel-jack connector on the rear of the charger. Do NOT use the USB port for charging.
  3. The charger’s power LED, on the rear panel, will illuminate dim green to indicate power is connected.

Charging
Attach the Inline Charger to the bottom of the compatible mobile computer (M7700 Striker, M7800 Scepter, or M7800 Solo) and it will begin charging immediately.

Introduction

The ACC-7715-PS Inline Charger charges any M7700 Striker, M7800 Scepter, or M7800 Solo Mobile Computer.

About This Guide
This guide provides instructions on setting up and using the ACC-7715-PS Inline Charger.

Set Up
Setting up the charger includes unpacking, connecting the power supply, and attaching the charger to your device.

Unpacking the Charger

The shipping box includes the following:

  • One ACC-7715-PS Inline Charger
  • One PWR-8050US Power Supply (12 VDC, 2.5 A)
  • This User’s Guide

Connecting the Power
The PWR-8050 power supply, included with the charger, is intended for 120VAC operation.

To connect power to the charger

  1. Plug in the PWR-8050 power supply to a standard 120 VAC electrical outlet.
  2. Connect the plug on the end of the power supply to the round, barrel-jack connector on the rear of the charger. Do NOT use the USB port for charging.
  3. The charger’s power LED, on the rear panel, will illuminate dim green to indicate power is connected.

Charging
Attach the Inline Charger to the bottom of the M7700 Striker, M7800 Scepter, or M7800 Solo Mobile Computer and it will begin charging immediately.

Indicator Lights

CHARGER STATE LED INDICATOR
The device disconnected with power GREEN (dim)
Charging in progress (including recharge) YELLOW
Charging complete GREEN (bright)

Charge faults:

1. Battery temperature too cold/hot

2. Battery over voltage

3. Charger too HOT

4. Safety timer expiration before battery completely charged

5. Internal charger fault

6. Battery not installed in the device

| ****


Flashing YELLOW/GREEN

No Power| OFF

How to Attach the Inline Charger

  • The Inline Charger should clip onto the rear of the device as shown.
  • Make sure the AML logo on the rear of the charger is not upside down.

Communication Ports
The ACC-7715 Inline Charger has one communication port and one power jack located on the rear of the charger. The charger itself has no internal or external settings that can be changed.

USB Type B
Connect to a PC (transfer files, software development)

© 2022 AML
7361 Airport Fwy

  • Richland Hills, TX 76118 800.648.4452
  • Local: 817.571.9015

FAQ

  • Q: Can I use a different power supply with the Inline Charger?
    • A: It is recommended to only use the AML-approved power supply (PWR-8050) to ensure proper functionality and safety.
  • Q: What should I do if the power LED does not illuminate when I connect the charger?
    • A: Check the power supply connection and ensure it is properly plugged into a 120 VAC outlet. If the issue persists, contact AML support for assistance.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals