Botslab G500H Car Dash Cam User Manual
- June 1, 2024
- Botslab
Table of Contents
Botslab G500H Car Dash Cam
Product appearance
Packing List
Upon opening the package, please check if the dash cam is in good condition and if all accessories are included.
- Main unit x1
- USB power cord x1
- Electrostatic film x 2
- User manual x1
- Installation pry bar x1
- Car charger x1
- Rear camera x1
- TF card x1 (optional)
Installation
Install the electrostatic film:
Install the electrostatic film on the front windshield in the recommended area
(dashed area) shown in the diagram below. Before installation, please clean
the glass and ensure there are no bubbles between the electrostatic film and
the glass.
Tip: Please install the dash cam as close to the middle area above the front windshield as possible, in order to ensure full coverage of the car’s front view and improve ADAS-assisted driving accuracy.
Attach the dash cam
Remove the 3M adhesive protective film, attach the dash cam bracket to the
electrostatic film, and adjust the dash cam to the appropriate angle.
Wiring and installation of the rear camera
Arrange the rear camera cable from the front windshield to the rear
windshield, as shown in the picture below.
Wiring and connecting the power supply
Route the power cord along the top of the front windshield, through the
A-pillar, and into the storage compartment located at the front passenger
seat, close to the cigarette lighter port, as shown in the diagram below.
Then, connect the power cord to the cigarette lighter power supply.
Tip: You can use the included wiring pry bar to bury the power cord under
the A-pillar sealant strip. Please note that the position of the cigarette
lighter port may vary between different vehicles, and the pictures are for
reference only.
ADAS Calibration Guide
To ensure the accuracy of ADAS, it is essential to perform ADAS calibration
before use.
After completing the wiring, the dashcam will power on automatically and start
recording. Upon the first power-up, ADAS calibration is required. Please
follow the steps shown in the diagram for adjustment. (If not the first power-
up, navigate to the ADAS calibration in the driving assistance section within
the settings menu.)
- Step 1: Adjust the installation position of the dashcam to align the vertical line of ADAS calibration with the centerline of the vehicle as much as possible.
- Step 2: Adjust the camera angle to align the horizontal line with the horizon of the road (the plane where the road meets the distance).
- Step 3: After calibration is complete, ADAS will become effective. For detailed ADAS function triggering conditions and alert content, please refer to the electronic manual.
ADAS functions are only used to provide information and cannot replace your observation of all roads and driving conditions. Please comply with traffic regulations and take responsibility for safe driving judgment. This function relies on recorder warnings, so the function may be limited under low visibility conditions.
Download and Installation of the App
- Method 1: Scan the QR code provided below to download and install the app.
- Method 2: Search for “botslab” in major application stores and click Download to install the botslab app.
User Guide
Scan the QR code to access the online version of Quick Start Guide, and obtain more detailed instructions on how to use the dash cam.
Precautions for Using the Dash Cam
- This product is an auxiliary device (dash cam) for safe driving.
- Any losses resulting from product malfunctions, data loss or product usage are not the responsibility of our company.
- This product is designed as an auxiliary device to record external images of vehicles. Due to different driving and vehicle environments, some functions may not be supported.
- Firmware upgrades are carried out periodically to improve the product, which may cause changes in product performance, and sometimes may lead to the inability to capture images due to the usage environment. Therefore, the driving images recorded in this product are for reference only.
- Although this product can record and save images of vehicle accidents, it does not guarantee that all accident images can be recorded. A minor collision accident may not activate the collision sensor, so the image may not be recorded in a dedicated folder.
- Do not install or operate this product while the vehicle is in motion.
- This product must be directly connected to the car’s power supply system and installed by professionals with installation experience. Do not use this product for a long time without starting the engine.
- This device may interfere with the function of improperly protected medical devices. If you have any questions or are uncertain whether the medical device can shield external RF energy, please seek advice from a doctor or the medical device manufacturer.
- Do not subject this product to strong shocks or vibrations, which may damage the product, resulting in malfunction or inability to use.
- Before cleaning or maintenance, please stop using the product.
- Do not use chemical solvents or cleaning agents to clean this product.
- Do not disassemble or modify this product without authorization.
- The normal temperature range for using this device is between 0 C and 50 C.
- Please ensure that you use this product within the limits allowed by law.
Important Statement
Personal Information Security
To ensure the safety of you and your family, please make sure that your
product is only bound by authorized persons. 360 will take strict measures to
ensure the security of your and your family’s information.
FCC regulatory conformance:
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.
Attentions And After-Sales Service
- Introduction and declaration of after-sales service
- Thank you for choosing the dash cam. Please use only the accessories provided by the original manufacturer to avoid unexpected malfunctions or damage. Failure to use the product as outlined here, or connecting it with incompatible accessories, will result in your warranty becoming void. The company assumes no responsibility for any danger or damage caused by such unauthorized uses. If you dismantle or change the product housing, the warranty will also become invalid.
- Our company is committed to constant improvement and sustainable development. As a result, we may modify and improve the product manual without advance notice to users.
- Unless otherwise specified by applicable laws, the manual contents are provided based on the product’s manufacturing conditions. Therefore, no explicit or tacit warranty of any kind is made for the correctness, reliability, or contents of the files.
- The product manual is protected by copyright law. Copying, transmitting, distributing, or using it in other forms is forbidden without the written approval.
- In regards to service policies within the warranty period of the dash cam:
1. This product contains a one-year warranty. For details on warranty service, kindly contact local authorized distributors.
2. The warranty period for the power adapter and charger cable is 12 months, and for the battery, it is 6 months.
3. Non-electronic accessories are not covered by the warranty. This symbol means the product must be discarded as household waste, and should
be delivered to an appropriate collection facility for recycling. Proper
disposal and recycling helps protect natural resources, human health and the
environment. For more information on the disposal and recycling of this
product, contact your local municipality, disposal service, or the shop where
you bought this product.
List of Performance Faults of Dash Cam
- Charged maintenance policies of recorder product
If any of the following cases occur, the Company or its authorized service centers will provide reasonable maintenance services at a cost for those outside the scope of the warranty.
1. Exceeding the valid warranty period.
2. Lack of warranty certificate or valid invoice. The warranty certificate does not match the model and labeling of the product or has been tampered with.
3. Damage caused by usage, repair, and maintenance that does not follow the requirements in the User Manual. Damage or malfunction resulting from personal removal, maintenance, or modification of the system software without authorization from the Company.
4. Collision, soaking, breaking or burning of the printed circuit board.
5. Cracking or damage to the outer shell, LCD screen, antenna, etc. of the dash cam during use, except for that caused by structural or material factors.
6. Damage due to force majeure.Contact Us
Website: https://www.botslab.com
Email: service@botslab.com
Facebook: @botslabofficial
RF Exposure
CE:
EU regulatory conformance:
RF exposure information: The Maximum Permissible Exposure (MPE) level has
been calculated based on a distance of 20cm between the device and the human
body. To comply with RF exposure requirements, it is recommended to use the
product while maintaining a distance of 20cm between the device and the human
body.
CE DOC
Hereby, Botslab Inc. declares that the radio equipment type G580H-N560-1
complies with Directive 2014/53/EU. The full text of the EU Declaration of
conformity is available on the following Internet.
address: https://www.botslab.com
Manufacturer information:
Company name: Botslab Inc.
Address: 919 North Market Street, Suite 950, Wilmington, New Castle,
Delaware, USA
Operation temperature: 0~50 C
Operation frequency(Max power)
Wifi: 2412MHz-2472MHz (<20dBm)
Bluetooth: 2402MHz-2480MHz (<13dBm)
FCC:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20 cm between the radiator and your body. This
transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
Responsible party (contact for FCC matters only): Botslab Inc.
919 North Market Street, Suite 950, Wilmington, New Castle, Delaware
www.botslab.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>