Botslab W315 Dual Lens PTZ Camera User Guide

Botslab W315 Dual Lens PTZ Camera

Packing list

Please check whether the main unit and all accessories are complete upon unpacking.

Product appearance

Network configuration instructions

Download and install the APP

• Method I: Scan the QR code below with your mobile phone to download and install the Botslab APP.
• Method II: Search and download the Botslab APP from the App Store or Google Play, and then install it.

Installation

Connect to a power

1. Connect the camera to the power adapter. After the camera is turned on, the status indicator light is “flashing green”, indicating that the device enters the network setup state and awaits being added.
   • Note: If the status indicator light is not flashing green, please reset the device now. Please use the original power adapter that comes with the camera.

Add camera

Launch the Botslab APP, tap the “Sign up” button, and start creating your account. If you already have an account, please log in directly and add a camera.

• Method I: Tap the “+11 button in the upper right corner of the APP homepage to “Add Device”, tap the “Camera11 button, tap and select the Duel-Lens PTZ Camera W315 icon to enter the distribution page, and add the camera as instructed.
• Method II: Tap the “+” button in the upper right corner of the APP homepage to “Scan11 the code, then use your mobile phone to scan the QR code at the bottom of the camera to enter the distribution page, and add the camera as instructed.

Notice:

• Complete the sound wave pairing in a quiet environment.
• Please press and hold the reset button until you hear a beep sound if the device failed to be added by connecting to the network, wait for the device to reboot, and then follow the steps above to add it again.

Installation guide

Insert a Micro SD card (optional).
Open the waterproof card cover with a screwdriver, insert the Micro SD card, and log in to the Botslab app for initialization before using it.

Wall-mounted Installation

• The camera supports both ceiling and wall-mounted installation. After selecting an appropriate installation method and location, securely affix the installation sticker. Drill holes and install the expansion pipe, then fasten the wall bracket with screws.
• The camera also supports hoop-mounted installation, where two cable ties are passed through the bar holes of the bracket and wrapped around an object such as a pipe, pole, etc., with each of the two cable ties being tightened.
• Align the card slot and push the camera upward into the fixed bracket, rotating it until it aligns with the wall bracket positioning marks.

Precautions:

• Please ensure that the camera has been successfully added before proceeding with the wall installation.
• The wall surface where the camera is installed must be able to support at least three times the combined weight of the camera and wall bracket.

Install a waterproof kit (optional)

1. Before installation, inspect the waterproof kit items and place the waterproof rubber ring on the camera’s network interface.
2. Thread the waterproof kit through the network cable one by one, and connect the network cable to the network interface.
3. Tighten the waterproof kit at the camera’s network interface first, and then screw the locking bolt.

After the installation is completed, connect the camera to the power source again. After startup, the camera will automatically connect to the pre- configured network.

Precautions:
The camera’s waterproof kit can effectively prevent rainwater from seeping into the network interface. Failure to install it properly may result in equipment damage, which is not covered by the after-sales warranty service.

Notes

1. For better night vision imaging, do not use the camera with the front or sides of the lens near reflective materials such as glass and white walls; otherwise, the images of things nearby will be rendered bright while those far away dark or even white.
2. Try to place the device in a place with good network signal reception. The distance between the device and metal objects (e.g., metal supports, metal doors, and windows) or other signal interference sources should not be too close.
3. Do not place the device near the heat source, e.g., electric heater, oven, or stove fire.
4. The applicable working temperature of this product is -20°C-+45°C. Please do not use it in an environment where the temperature is too high or too low.
5. Please do not use this product in an environment that is excessively humid and may cause water ingress.

Operating mode description

The manufacturer reserves the right to adjust the functional status of the product through firmware upgrades or software adjustments.

This symbol means the product must be discarded as household waste, and should be delivered to an appropriate collection facility for recycling. Proper disposal and recycling help protect natural resources, human health and the environment. For more information on the disposal and recycling of this product, contact your local municipality, disposal service, or the shop where you bought this product.

IMPORTANT

Personal information security
For the safety of you and your family, please make sure that the products you purchase are not bound to any unauthorized person. Botslab will take strict measures to protect the information security of you and your family.

Description of Hazardous Material Contents

Note:
A small patch of electronic components for special purposes is marked with “X” in the table (such as high voltage resistors, ceramic resistors, and diodes), in which the lead content may exceed 0.1%. As the screws and the core in the data cables use alloy with better performance, the lead content may also exceed 0.1%. These components are per the requirements of the exemption clause of the EU RoHS directive. Limited by the current global technology development, there are no other alternative technologies and components. The external lead contents of these components are under environmental protection requirements.

Declaration of Conformity

Hereby, Botslab, Inc. declares that the radio equipment type W315 of Botslab Dual lens PTZ Carema is in compliance with Directive 2014/53/EU and this product is allowed to be used in all EU member
states. The full text of the EU Declaration of Conformity is available at the following internet address: www.botslab.com.

• Operation frequency (Max. power)
• Bluetooth: 2402-2480MHz (<20dBm).
• Wifi: 2412MHz-2472MHz (<20dBm)

RF exposure statement

RF exposure information:
The Maximum Permissible Exposure (MPE) level has been calculated based on a distance of d=20 cm between the device and the human body. To maintain compliance with RF exposure requirements, use products that maintain a 20cm distance between the device and the human body.

Restriction in BE, BG, CZ, DK, DE, EE, IE, EL, ES, FR, HR, IT, CY, LV, LT, LU, HU, MT, NL, AI, PL, PT, RO, SI, SK, FI, SE, UK(NI).

UK Declaration of Conformity
Hereby, Botslab, Inc. declares that the product complies with the essential requirements and other relevant provisions of Radio Equipment Regulations 2017(SI 2017 No.1206). You can find the Declaration of Conformity on www.botslab.com.

The device complies with RF specifications when the device is used at least 20cm from your body.

RF Operating frequency(Max Power):

• Bluetooth: 2402-2480MHz (<20dBm)
• Wifi: 2412MHz-2472MHz (<20dBm)

IC regulatory conformance
This device complies with CAN ICES-003 (B)/NMB-003(B). This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

• this device may not cause harmful interference, and
• this device must accept any interference received, including interference that may cause undesired operation.

RF Exposure
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note:
This equipment has been tested and found to comply with the limits for a Class B digital device, according to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used per the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interterence will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and the receiver.
3. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.

This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be collocated or operating in conjunction with any other antenna or transmitter.

Responsible party (contact for FCC matters only): Botslab Inc. 919 North Market Street, Suite 950, Wilmington, New Castle, Delaware www.botslab.com.

After-Sales Service

Warranty policy
This product comes with a one-year Local Warranty Service. For details of warranty service, please kindly contact local Authorized Distributors in your country.

Non-warranty policy

• Cannot present valid warranty certificate and purchase invoice.
• Damage caused by use, maintenance, or keeping of the product, not under the product description, damage caused by disassembly and repair unauthorized by Botslab, or artificial damage.
• Damages that result from force majeure.
• Normal decolouration and wastage during usage will not be included in warranty service.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>