Botslab W302 Outdoor Dual-Lens Camera User Guide

June 13, 2024
Botslab

Bo slab Outdoor Dual-Lens Camera
Quick Start Guide

Botslab W302 Outdoor Dual-Lens Camera Packing list

Please check whether the main unit and all accessories are complete upon unpacking.

Product appearance

Due to ongoing updates and iteration of the product, there may be slight differences between the physical and schematic diagrams. Please refer to the actual products for the most accurate information.

Memory card: Maximum 256GB

Guideline for Connecting to the Network

Download and install the APP
Method 1: Scan the QR code below with your mobile phone to download and install the Botslab APP.
Method 2: Search and download the Bo slab APP from App Store or Google Play, and then install it.

https://www.botslab.com/superappdownload.html

Connection Guide

  • Before using the app to add a camera, please refer to the following diagram and connect the camera according to the prompts below.
  • Connect the camera to the power supply
  • If the indicator light slowly flashes green, this indicates that the device is ready for setup.

Add the Device
Open the Bo slab app, click the Register button to register a Bo slab account. If you already have an account, click the “Login” button, and enter your account and password to log in.
Method 1

  1. Connect the camera to the power supply, press and hold the Reset button to enter the network setup mode, and follow the voice prompts.
  2. After logging in, Bluetooth will automatically search for the camera by default. Once the camera is found, add the device according to the prompts.

When connecting to the network, please make sure that Bluetooth is enabled on the mobile phone and that the WiFi is properly connected.
If the network has not been configured, there is no need to press the RESET button for the initial configuration
Method 2
After logging in, click the “+” button on the upper right corner of the homepage, select “Scan” and use your mobile phone to scan the QR code on the camera to enter the network setup page. Follow the prompts to add the camera

Botslab W302 Outdoor Dual-Lens Camera - App1

Method 3 After logging in, click the “+” button on the upper right corner of the app’s homepage to add a camera by the model

Installation Guide

Installation method

  1. Please use the original adapter to prevent overvoltage and overcurrent from damaging the product.
  2. Pay attention to outdoor lightning protection measures.

Antenna Installation
and Adjustment When the antenna is parallel to the camera, it can affect signal reception.

Botslab W302 Outdoor Dual-Lens Camera - Fig2

Installation Bracket

  1. Attach the positioning sticker to the wall and according to the position shown in the diagram
  2. Insert the expansion bolt into the wall at the sticker’s hole position.
  3. Fix the bracket base with screws.

Botslab W302 Outdoor Dual-Lens Camera - Fig3

Installation of the Camera

  1. Rotate the camera body and screw it into the bracket. Adjust the camera position, and view the image’s fixed position through the app.
  2. Tighten the bracket by rotating the nuts and bracket base. 3.Adjust and unfold the antenna to the appropriate position.

Precautions

Installation method

  1. To achieve better night vision imaging results, keep the lens front or side away from reflective objects such as glass and white walls. This will prevent nearby objects from appearing too bright while distant objects may appear dark or white.
  2. Place the device in a location with good network signal reception and keep it away from metal objects (such as metal brackets, metal doors, and windows) or other sources of signal interference.
  3. It is normal that the equipment generates heat during operation
  4. This product is designed to operate within a temperature range of -10°C to +60°C. Do not use this product in environments that are too hot or too cold.
  5. Please use the original power cord to ensure safety of power supply and good user experience.

Working Status Description

Indicator light status Meaning of indicator light
Flashing blue Camera is online
Constant blue Camera video is being viewed
Flashing green The device is currently bound but offline
Quickly flashing green Device is upgrading
Constant green To be networked/camera is offline

The manufacturer reserves the right to adjust the product’s functional status through firmware upgrades or software adjustments.

Important Statement

Personal information security
For the safety of you and your family, please make sure that the products you purchase are not bound to any unauthorized person. Botslab will take strict measures to protect the information security of you and your family.
Description of Hazardous Material Contents

Component Hazardous substances and elements
Lead (Pb) Mercury (Hg)
Polybrominated Bi phenyls (PBB) Polybrominated Diphenyl Ethers (PBDE)
Plastic enclosure O
Circuit board components X
Power cable X
Adapter X
Lens O

This form is prepared in accordance with Si/T11364.
O :It indicates that for each item in this part, the hazardous substance is below the requirements set forth by the standard GB/T26572.
X :It indicates that the hazardous substance in at least one homogeneous material of this part exceeds the limit specified in GB/T26572. However, it satisfies the limit requirements specified in the List of Exempt Applications of Hazardous Substances Identified in the Management Catalog.
Remarks: The lead content in a small number of special-purpose SMT electronic components (such as high-voltage resistors, ceramic resistors, diodes, etc.) in the part labeled “x” in the above table may be = 0.1%. The lead content in screws or cores of data cables can be 20.1% due to the adoption of high-performance alloy. These components are in compliance with exemption clauses of the EU RoHS Directive. At this stage, due to the limitations of the global technological development level, there is no alternative technologies and parts, and the lead content of the external contactable parts of the product meets the environmental protection requirements.

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference.
  2. This device must accept any interference received, including interference that may cause undesired operation.
    2. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. if this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
ISED Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

  1. This device may not cause interference.
  2. This device must accept any interference, including interference that may cause undesired operation of the device.

This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body.
CE Declaration of conformity
This product complies with the radio interference requirements of the European community. Hereby, Bo slab, Inc. declares that the product is in compliance with the essential requirements and other relevant provisions of RE Directive 2014/53/EU. You can find the Declaration of Conformity on http://Avww.botslab.com. In accordance with Article 10(2) and Article 10(10),This product is allowed to be used in all EU
member states.
The device is restricted to indoor use when operated in the European Community using frequency 51S50MHz-52SO0MHz to reduce the potential for interference.
The device complies with RF specifications when the device used at least 20cm. from your body.
RF power: XXXXX
RF frequency band: XXXXXX
The operating temperature of the product is:XXXXxXx
Manufacturer Name: Bo slab Inc.
Address: 919 North Market Street, Suite 950, Wilmington, New Castle, Delaware, USA
Product Name: Bo slab Outdoor Dual-Lens Camera
Trademark: Bo slab
Product Model: W302

After-Sales Service

Warranty policy for Bo slab Video Doorbell
This product comes with a one-year Local Warranty Service.
For detail of warranty service, please kindly contact local
Authorized Distributors in your country.
Non-warranty policy for Bo slab Video Doorbell

+ No valid warranty certificate and purchase invoice.
+ Damage caused by use, maintenance, or keeping of the product not in accordance with product description, damage caused by disassembly and repair unauthorized by Bo slab, or artificial damage.
+» Damages that result from force majeure.

  • Normal discoloration and wastage during usage will not be included in warranty service.

Contact Us

**https://www.botslab.com
 service@botslab.com
Facebook@botslabofficial
1-866-360-0505 (Only for US)
Working time:** Mon-Fri, 9:00 – 17:00 EST

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals