Enboya P30 Smart kitchen Waste Composter User Manual
- June 1, 2024
- Enboya
Table of Contents
Enboya P30 Smart kitchen Waste Composter
Please read the manual carefully before using g the product and keep it for future reference.
Important Safety Instructions
When using this product, please maintain constant vigilance and adhere to the following guidelines. Before using the product, please read and store this manual carefully.
warnings
- To prevent electric shock, keep the power cord, plug, and the disposal unit away from water and other liquids.
- Do not immerse the disposal unit in any liquid, including water.
- Place the unit and power cord out of the reach of children.
- When children or individuals with disabilities operate the unit, they should be accompanied and supervised by an adult.
- To avoid accidental activation, unplug the unit from its socket when it is not in use, before removing parts, and before cleaning.
- The disposal unit can be used in your kitchen. If it’s placed near a sink, ensure there is a power protection device installed. If the unit experiences a short circuit or malfunctions, contact the customer service promptly.
- The voltage for the disposal unit is 120V. Ensure proper power supply.
- Do not let the power cord hang off the edge of countertops or tables.
- After the unit completes a cycle (approximately 35 minutes), open the lid to allow the disposal unit to cool down. If continuous use is required, allow all internal components to fully cool.
- Do not open the disposal lid during operation. To open the lid, simultaneously press and hold the Standard Mode button and the Quick Mode button to stop the current cycle, then press and hold the Power button to turn off the unit.
- Do not place your hands inside the unit unless the disposal unit has completed its operational cycle.
- Do not disassemble unit components without proper authorization. Do not reach into the inner bucket while the inner bucket is in place.
- Do not operate any unit with damaged power cords or plugs. If the power cord is damaged, it must be replaced or guided by the manufacturer, service agent, or qualified personnel to prevent electrical hazards.
- Do not operate the unit if it has defects or potential malfunctions.
- The disposal unit is intended for indoor use only; avoid exposing the unit to outdoor conditions.
- Do not place the unit near heat sources, open flames, gas burners, or hot surfaces.
- Avoid placing the disposal unit in a heated oven.
- Do not exceed more than half the capacity of the inner bucket with accumulated waste before processing.
- Under no circumstances should the disposal unit be disassembled, modified, altered, or tampered with.
- Allow proper air circulation by placing the disposal unit at least 0.5ft / 15cm away from the wall and in a well-ventilated area.
- Ensure the disposal unit is placed on a flat, dry, and stable surface.
- Do not put food waste into the unit when the inner bucket is not in place.
- Do not consume or ingest dehydrated food waste or any items placed in the bucket.
- Follow the recommended maximum fill line for food waste disposal. Do not add any food waste above this line to prevent damage and malfunctions.
- Once food waste exceeds the maximum fill line (4.2L), do not compact or add more waste, as overloading the unit can lead to clogs.
- Always ensure no food waste falls outside the bucket or inside the unit.
- Do not place any food waste larger than the size of a palm into the bucket. Ensure to chop hard stems/fibrous vegetables (such as broccoli stalks, cauliflower stalks, kale stems, etc.) to prevent them from getting stuck during the grinding process.
Packing List
Product Overview
Using the Unit
Operation Interface Instruction / Display and Controls
- Lid Lock Indicator : In standby mode and when no cycle is active, the light will be off. In standard/ quick/ self-cleaning mode, the light will be on, indicating that the lid is locked.
- Inner Bucket In-Place indicator : Please adjust the position of the inner bucket for correct installation
- Activated Carbon Box Indicator : After the activated carbon box has been used for a cumulative total of 1000 hours, the indicator light will flash red slowly. Please replace the box. After replacement, press and hold the Clean button for 3 seconds to turn off the flashing.
- Standard Mode Indicator : When the unit is operating in standard mode, the white light will stay on until the cycle is completed.
- Quick Mode Indicator : When the unit is operating in quick mode, the white light will stay on until the cycle is completed.
- Self-Cleaning Indicator : When the unit is in self-cleaning mode, the white light will stay on until the cycle is completed.
- Timer Display : Once a cycle is initiated, the timer starts, and two dots in the middle will flash at a frequency of once per second. The “h” and “m” indicators will stay on.
Preparation
-
Remove the deodorizing filter, peel off the sticker on it, and then reinstall the deodorizing filter into the unit.
-
Plug the power cord into an electrical outlet. You’ll hear a beep sound indicating the power is on.
-
Press the power button . You will hear a beep sound, indicating that the unit has entered standby mode.
-
Press the lid open button to open the lid.
The power switch is factory-defaulted to the “on” position. -
Pour kitchen waste into the unit’s inner bucket, ensuring it does not exceed the maximum marking line. The inner bucket can be removed separately.
-
Close the lid. You will hear a click sound, indicating the lid is closed.
-
Select either the standard mode or quick mode to start the processing cycle.
-
After completing a cycle and entering standby mode, press and hold the power button for 3 seconds to shut down. All indicator lights will be off.
- It is recommended not to remove the inner bucket. Instead, directly pour kitchen waste into the bucket, as removing the inner bucket may make accurate installation more difficult.
- If the inner bucket has been removed, align it according to the markings on the handle and the chamber. If you encounter a situation where the lid cannot be closed, gently rotate the blades to correctly install the inner bucket.
Operation Modes
Standard Mode
In standby mode, press the Standard Mode button. The unit will emit a beep
sound and enter the standard mode of operation. The lid will be locked, and
the Lid Lock Indicator as well as the Standard Mode Indicator will stay on.
The timer on the display will start counting. After completing the cycle, the
unit will automatically enter standby mode.
Self-Cleaning Mode
Open the lid and add water to the bucket until it reaches the marked water
level on the inner wall of the bucket. Then close the lid. In standby mode,
press the Self-Cleaning button. The unit will emit a beep sound and enter the
self-cleaning operation. The lid will be locked, and the Lid Loc Indicator as
well as the Self-Cleaning Indicator will stay on. The timer on the display
will start counting. After completing the process, the unit will automatically
enter standby mode.
Quick Mode
In standby mode, press the Quick Mode button. The unit will emit a beep
sound and enter the quick mode operation. The lid will be locked, and the Lid
Lock Indicator as well as the Quick Mode Indicator will stay on. The timer on
the display will start counting. After completing the cycle, the unit will
automatically enter standby mode.
Forced Termination
In any operation mode, simultaneously press and hold the Power button
power for 3 seconds to forcibly terminate the current cycle. The device
will enter a cooling phase and automatically end the operation.
Maintenance and Care
Maintenance and Care
Important Notes
- Before cleaning, please turn off the unit and unplug it from the power source.
- Do not immerse the device directly in water or any liquids during cleaning, as this may cause circuit damage and cause electrical hazards.
- It is recommended to place this unit on a kitchen countertop rather than on the floor.
- Pouring foods with a high oil content may result in moist and viscous kitchen waste after processing.
- We recommend not removing the inner bucket. Instead, directly pour kitchen waste into the bucket with the inner bucket installed to avoid difficulties in accurate installation.
- If you encounter a situation where the lid cannot be closed, please ensure that the inner bucket is correctly installed. First, align the arrow markings on the inner bucket handle and the chamber, then gently rotate the blades to ensure the inner bucket is correctly installed in place.
- During the kitchen waste processing, the initial mixing process may cause a slight increase in noise, but it will quickly quiet down.
- During kitchen waste processing, the unit’s body may generate slight heat, which is normal.
- The outlet temperature during kitchen waste processing may be higher. It will not damage wires or furniture, but do not block the outlet or touch it with your hand.
- It is generally not recommended to stop the current cycle and add new kitchen waste midway. If there is a special situation requiring you to stop the current cycle, press the Power button for 3 seconds to force stop the current cycle.
- After processing kitchen waste, the lid remains in a secure locked state because the unit needs to cool down to a safe temperature. The ventilation outlet continues to operate, and this process lasts approximately 40 minutes. Once ii reaches a safe temperature, the lid will automatically unlock, and the ventilation outlet will stop working.
- The inner bucket is coated with a non-stick layer and can be cleaned in a dishwasher. The blades can also be disassembled for cleaning.
- Handle the processed kitchen waste with care and keep ii out of reach of pets or children to prevent ingestion.
- The P30 has a large 530ml carbon box, so you don’t need to worry about odors. However, please maintain the carbon box by ensuring that the air inlet and outlet are not blocked before using the unit. It is recommended to replace the activated carbon every 2 3 months, depending on usage. The activated carbon used in the P30 is biodegradable and environmentally friendly.
- The Quick Mode is recommended for common kitchen waste not exceeding 1.5 liters.
- If you have any questions during use or encounter error messages on the product display, please contact support@enboya.com.
Replacing the Filter
The filter needs to be replaced regularly to ensure the deodorizing
effectiveness of the unit. It is recommended to replace it every 3-6 months.
(Recommended filter specifications: Coal-based columnar activated carbon /
black/ diameter 4mm / iodine adsorption value (mg/g) >1000)
- Disconnect the power supply to the unit and then pull out the filter from the back of the unit.
- Open the filter cover and remove the used filter material. Clean the inside of the filter thoroughly and let it dry.
- Insert the new filter material and close the filter cover.
- Properly reinstall the filter back into the unit.
Cleaning the Inner Bucket and Blades
- Remove the inner bucket from the unit.
- Press the blade release button down and then firmly pull the blade assembly upwards to remove it from the inner bucket.
- Use the cleaning brush to remove debris from the inner bucket, the exhaust fan filter, and the blades. Rinse them thoroughly with water.
- Allow all components to air dry completely to ensure they are free from moisture.
- Align the blades with the central axis of the inner bucket. Adjust the angle as needed. Press down firmly on the blades until you hear a click sound, indicating the blades are securely in place. Then, install the inner bucket back to the unit.
- Align the arrows on the edge of the inner bucket, the inner bucket handle, and the chamber to be in the same line to ensure the inner bucket is correctly installed. Otherwise, the lid cannot
Tips:
- The inner bucket is dishwasher safe.
Fault Codes and Troubleshooting Guide
|
---|---
E01| Lid Not Closed or Faulty Sensor
E02| Inner Bucket Not Installed
E03| Turntable Motor Open/Short Circuit or Jammed Over 50 Times
E04| Cooling Fan Jammed/Open Circuit
E05| Heating Plate Overheating (Above 150°C)
E06| Temperature and Humidity Abnormal
| |
---|---|---
Indicator Light Flashing Red
|
Potential Malfunctions During Operation
| 1. Turn off the unit and unplug the power cord. Wait for the inner bucket of the unit to cool down for 30 to 60 minutes.
2. Check the inner bucket of the unit to ensure that it is not obstructed by foreign objects.
3. Check the fan and exhaust pipe to ensure they are not blocked by foreign objects.
4. Ensure that the inner bucket is properly installed in place.”
Strong Odor During Operation
|
Expired Deodorizing Device or Clogged Deodorizing Filter Impairing Exhaust
| 1. Turn off the unit and unplug the power cord. Wait for the inner bucket of the unit to cool down for 30 to 60 minutes.
2. Check if the filter material of the unit is clumped together, and decide whether replacement is necessary.
3. Regularly clean the unit and replace the deodorizing filter.”
Extended Process ing Time
| Excessive Moisture Content in the Food Waste Deposited
into the Inner Bucket
|
1. Turn off the power and unplug the power cord. Wait for the inner bucket of the device to cool down for 30 to 60 minutes.
2. Check if the filter material of the unit is clumped together, and decide whether
replacement is necessary.
3. Please try to drain excess moisture from food waste before disposing of it.”
Blockage in the Internal
Exhaust Filter or Deodorizing Filter
- Temperature and Humidity Abnormality Indicator : When the temperature and humidity sensor detects abnormal data, the indicator light will flash red rapidly.
- Healing Plate Abnormality Indicator : When the heating plate’s temperature is abnormal, the indicator light will flash red rapidly. Please wail for the heating plate’s temperature to return to normal. Once it does, the flashing will stop and the light will be off.
- Blade Abnormality Indicator : When foreign objects obstruct the blades inside the bucket, the indicator light will flash red rapidly. Please wait for the temperature inside the bucket to decrease to a safe level. Once the lid is unlocked, open the lid and clear the obstruction. After closing the lid, the unit will resume the cycle that was ongoing before the malfunction occurred.
- Cooling Fan Malfunction Indicator: When the cooling fan malfunctions, the light will flash red rapidly. Please contact customer service promptly.
- Sterilization Malfunction Indicator : When the UV lamp malfunctions, the light will flash red rapidly. Please contact customer service promptly.
For after-sales support, please contact support@enboya.com.
Specifications
Due to the need for continuous improvement of the product, this information is based on the actual product, and our company reserves the right to update the product.
| Product Model | P30 |
|---|---|
| Product Dimensions | 13.3″ L x 12.8″ W x 15″ H (33.7 x 32.6 x 38 cm) |
| Maximum Inner Bucket Capacity | 4.2L |
| Rated Power | 450W |
Rated Voltage
| 120V
Weight| 17.6 lbs (8kg)
Filter Weight| 1.1 lbs (500g)
Storage Environment| 0-45C
Processing Time| Standard Mode: 8 – 10 hours Quick Mode: 2 – 5 hours Self-
Cleaning Mode: 16 – 20 hours
Processing Cycles| Drying, Grinding, Cooling
Noise
|
<45dB
- For after-sales support, please contact support@enboya.com.