abetap N002 Bird Feeder Cam User Guide

abetap N002 Bird Feeder Cam

What’s In The Box

• Black Strap

• Roof
  

• Mounting Screws

• Anchors

• Perch Screw

• Perch

• Bird Feeder Cam
  

• Hose Clip

• Ejector Pin

• Quick Guide
  

• Type C Power Cable

• Mounting Bracket
  

Camera Structure

Insert Micro SD Card

Bird Cam comes with a built-in card slot which supports up to 128GB Micro SD card.

Step 1: Rotate the camera down to the bottom.
Step 2: Open the top silicone plug. Insert the Micro SD card. Make sure to plug it in the right direction.
Step 3: Finally, Cover silicone plug.

Assemble Bird Feeder Cam

Assemble Perch
Use the provided perch screw to install the perch.

Battery Charging

The batteries inside the camera are not fully charged according to the transportation safety regulations. Please fully charge the camera before using it. Please charge the batteries with provided Type C Port Cable (DC5V/1.5A adapter not included).d The status light will be in solid yellow when charging, and will turn to solid green when it is fully charged. It takes about 14 hours to fully charge your camera.

How To Turn On & Off The Camera

To turn on the camera:
Long press the power button for 3s to turn on the camera. Then the Status Light in the front of the camera will be solid blue. Double click the power button to enter WiFi mode after the prompt tone.

To turn off the camera:
Long press the power button for 3s to turn off the camera. Then the Status Light in the front of the camera will be off.

Read Before Installation

1. Keep Bird Feeder Cam and all accessories out of reach of children and pets. d
2. Make sure the camera has been fully charged (DC5V/1.5A).
3. Working temperature: -10°C to 50°C (14°F to 122°F) Working relative humidity: 0-95%
4. Please do not expose the camera lens to direct sunlight.
5. The camera has an IP65 waterproof rating, which supports working properly under rains or snows. But it can not be soaked in water.

Note:

1. Bird Feeder Cam only works with 2.4GHz Wi-Fi.
2. Strong lights may interfere with the device’s ability to scan QR code.
3. Avoid placing the device behind furniture or near microwaves products. Try to keep it within range of your Wi-Fi signal.

Set Up With VicoHome App

|
---|---

App Download

|

Download VicoHome App from App Store or Google Play. Follow the in-app instruction to complete the entire set up process.

Power on/off and network configuration

• Long press the power button for s to power on/off the device.
• Double click the power button to enter the network configuration mode after the prompt tone.

When connecting the camera for the first time, use the App and follow the instruction to configure the camera network.

Set up the camera

1. Click the “Add Camera Now” in the App and enter the Wi-Fi network name and password that you want the camera to connect. To ensure a longer distance connection, the camera only supports the 2.4Ghz Wi-Fi with stronger wall penetration capability and does not support Wi-Fi for enterprise-level authentication currently. Please ensure that the entered Wi-Fi meets the requirements. After completion, click “Continue” to generate the QR code for pairing the camera.
   

2. After pressing the camera switch for 3 seconds, the camera will turn on. At this moment, target the camera at the QR code of the mobile App, with a distance of about 20cm (about 7 inches) until the camera emits a “Di” sound, which represents the scanning is succeeded and the pairing is started.
   

3. After a while, the camera will give out a prompt sound of a successful connection. At this moment, please set the name for the device on the App and select the location you want to place the device. Click “Continue” to complete the pairing.
   

Installation

Check the following things before you drill holes on your wall:
Bird Feeder Cam has been successfully added to your VicoHome App and is able to stream video.

Wall Installation:

Step 1:

1. Use the provided drilling template to mark the position of holes on your wall.
   Use drill bit(5/16,8mm) to drill two holes.

2. Install the anchors to fix the screws.(Install on wood skip this step.)

3. Install the Mounting Bracket on your wall with the screws provided.
   

Step 2:
Slide the Bird Feeder Cam into the bracket through the slide rail.

Tree Installation:

Step 1: Wrap the Mounting Bracket around the tree with the Black Strap.

Step 2: Slide the Bird Feeder Cam into the mounting bracket.

Stand Installation:

Step 1:
The Bird Feeder Cam can be placed steadily on a flat surface, but for stability, we recommend that the backplane is installed and fixed on a flat surface.
Use the provided drilling template to mark the position of holes on flat surface.
Use drill bit (5/16″, 8mm) to drill two holes.

Step 2:
Install the anchors to fix the screws. (Install on wood skip this step.)

Step 3:
Install the Mounting Bracket on flat surface with the screws provided.

Step 4: Slide the Bird Feeder Cam into the mounting bracket.

Pole Installation – Hose clip

Step 1: Attach Bird Feeder Cam to the pole with the Hose Clip turning the handle clockwise.

Step 2: Slide the Bird Feeder Cam into the bracket through the slide rail.

Installation Of Solar Panels

Step 3: Screw the bracket to the wall, then rotate the solar panel so the 1/4″ nut on the back fits with the 1/4″ screw on the bracket.

Step 4: Open the back cover, pass the solar panel cable through the rear, connect it to the camera at the front of the device, and then close the back cover

Cleaning Bird Feeder Cam

Step 1: Unplug the charging cable and put on the silicone cover.

Step 2: Using the Pull Tab on the base of the feeder, remove the Bird Feeder Cam from the bracket.

Step 3: Open up the buckle on the back of the Bird Feeder Cam, and pull up on the roof to open.

Step 4: Pour water into the top of the seed reservoir. Do not wash the camera or any of its components. They are water resistant, not water-proof. Dry the feeder, including the seed reservoir.

Step 5: Re-attach the Roof: Push the roof down and engage the snaps on the back of the Bird Feeder Cam.

Step 6: Re-attach the bracket to the Bird Feeder Cam base. Adjust the angle for both the Bird Feeder Cam and camera.

Step 7: Open the silicone plug, re-plug in the Solar Lite.

How to Add Bird Seed

Step 1: Open up the buckle on the back of the Bird Feeder Cam, and pull up on the roof to open.

Step 2: You can add bird seed. Finally, close the roof back.

Status Light

This camera uses status light to communicate.

Al Bird Recognition

* Al version:* The service is free for life.
Lite version:** This service requires a subscription.

Al Bird Recognition has undergone massive machine learning and uses Al intelligent recognition algorithms to inform you in real time “what species of bird are coming”, automatically save the bird images/videos data for you, and also provide bird knowledge learning and so on.

Warning

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful int efference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The antennas used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be co- located for operating in conjunction with any other antenna or transmitter.

FCC (USA) 15.9 prohibition against eavesdropping except for the operations of law enforcement officers conducted under lawful authority, no person shall use, either directly or indirectly, a device operated pursuant to the provision of this part for the purpose of overhearing or recording the private conversations of other unless such use is authorized by all of the parties engaging in the conversation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

IC Caution:

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and

Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

This device may not cause interference.
This device must accept any interference, including interference that may cause undesired operation of the device.

CE RED This product can be used across EU member states.

NOTE: If you encounter problems with the product during use or before returning it, you can contact us by scanning the QR code.

Get 24/7 Assistance at

Use camera or QR scanner to scan

Customers Support

Visit: https://abetap.afterservice.vip
Call: +1 (833} 924 2196 (Toll-free)
Email: abetap@afterservice.vip

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>