DIMPLEX DLG1058 28-in Premium Electric Fireplace Log Set Owner’s Manual
- June 3, 2024
- Dimplex
Table of Contents
Better solutions through innovation
Owner’s Manual
Model
DLG1058
DLG1058 28-in Premium Electric Fireplace Log Set
IMPORTANT SAFETY INFORMATION : Always read this manual first before
attempting to install or use this Log Grate. For your safety, always comply
with all warnings and safety instructions contained in this manual to prevent
personal injury or property damage.
To view the full line of Dimplex products, please visit
www.dimplex.com
Always use a qualified technician or service agency to repair this Log Grate.
NOTE: Procedures and techniques that are considered important enough to
emphasize.
CAUTION: Procedures and techniques which, if not carefully followed, will
result in damage to the equipment.
WARNING: Procedures and techniques which, if not carefully followed, will
expose the user to the risk of fire, serious injury, or death.
Welcome & Congratulations
Thank you and congratulations for purchasing an electric fireplace from
Dimplex. Please use our convenient online registration page to record your
model and serial numbers for future reference at
www.dimplex.com/register
Please carefully read and save these instructions.
CAUTION: Read all instructions and warnings carefully before starting
installation. Failure to follow these instructions may result in a possible
electric shock, or fire hazard and will void the warranty.
**** IMPORTANT INSTRUCTIONS
When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following:
-
Read all instructions before using the Log Grate.
-
The heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. The trim around the heater outlet becomes hot during the heater operation. Keep
combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9m) from the front of the unit. -
Extreme caution is necessary when any heater is used by or near children or invalids and whenever the unit is left operating and unattended.
-
Always unplug the Log Grate when not in use.
-
Do not operate any unit with a damaged cord or plug, if the heater has malfunctioned, or if the Log Grate has been dropped or damaged in any manner. Return the heater to an authorized service facility for examination, electrical or mechanical adjustment, or repair.
-
Do not use outdoors.
-
The Log Grate is not intended for use in bathrooms, laundry areas, and similar indoor locations. Never locate the heater where it may fall into a bathtub or other water
container. -
Do not run the cord under the carpeting. Do not cover the cord with throw rugs, runners, or the like. Arrange the cord away from the traffic area so that it will not be tripped over.
-
To disconnect the unit, turn the controls off, then remove the plug from the outlet.
-
Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage to the heater.
-
To prevent a possible fire, do not block air intake or exhaust in any manner. Do not use it on soft surfaces, like a bed, where openings may become blocked.
-
All electrical heaters have hot and arching or sparking parts inside. Do not use in areas where gasoline, paint, or flammable liquids are used or stored or where the unit will be exposed to flammable vapors.
-
Do not modify the Log Grate. Use it only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock or injury to persons.
-
To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way. Always plug heaters directly into a wall outlet/ receptacle. Never use it with an extension cord or relocatable power tap (outlet/power strip).
-
Do not burn wood or other materials in the Log Grate.
-
Always use a certified electrician should new circuits or outlets be required.
-
Always use properly grounded, fused, and polarized outlets.
-
Disconnect all power supplies before performing any cleaning, maintenance, or relocation of the unit.
-
When transporting or storing the unit and cord, keep them in a dry place, free from excessive vibration, and store them so as to avoid damage.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
NO USER-SERVICEABLE PARTS INSIDE
SAVE THESE INSTRUCTIONS
**CAUTION:** This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions may cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. Operation is subject to the following two conditions: (1) this device may not cause interference and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
**WARNING: Remote control contains small batteries. Keep away from
children. If swallowed, seek medical attention immediately.
WARNING: Do not install the battery backward, charge, put in the fire, or
mix with used or other battery types – may explode or leak causing injury.
! NOTE:** Changes or modifications not expressly approved by the party
responsible for compliance could void user’s authority to operate the
equipment.
Log Grate Assembly
**CAUTION:** Handle logs carefully, they are fragile and can easily crack
or break, if dropped. Each log is a separate component that needs to be placed
on the grate. Position each log so that the hook and loop dot on the backside
of the log lines up with the corresponding hook and loop pad on the Log Grate.
These pads assist with securing the logs to the grate.
Each of the logs contains LED lights to create a flickering effect. During
assembly, each log requires the electrical connectors on the log and grate to
be connected as they are being placed. In some cases, these wires will need to
have tie wraps added to prevent the wires from being seen after final
assembly.
! NOTE: A 15amp, 120 volt circuit is required. A dedicated circuit is
preferred but not essential in all cases. A dedicated circuit will be required
if, after installation, the circuit breaker trips or the fuse blows on a
regular basis when the heater is operating. Additional appliances on the same
circuit may exceed the current rating of the circuit breaker.
WARNING: Ensure the power cord is not installed so that it is pinched or
against a sharp edge and ensure that the power cord is stored or secured to
avoid tripping or snagging to reduce the risk of fire, electric shock, or
injury to persons.
Construction and electrical outlet wiring must comply with local building
codes and other applicable regulations to reduce the risk of fire, electric
shock, and injury to persons.
Do not attempt to wire your own new outlets or circuits. To reduce the risk of
fire, electric shock, or injury to persons, always use a licensed electrician.
- Make sure the unit On/Off switch is switched OFF (refer to operating instruction section).
- Plug the unit into a 15 Amp/120 volt outlet.
! NOTE: For optimal flame projection, it is recommended that the unit be
placed 4″ (10.2 cm) from the back of the mantel. The addition of a mesh spark
screen in front of the Log Grate and Fireplace tools can be used to complete
the look of your hearth. To enhance the look of the Log Grate, further, non-
toxic materials such as cat litter and/or lava rock to replicate the look of
ashes and embers can also be used.
CAUTION: We do not recommend the use of additional decorative material in
homes with young children or pets where these materials could be a choking
hazard.
Operation
The manual controls for the Log Grate are located on the front right side.
(Figure 1)
A. On/Off Switch Supplies power to the 2-Position Switch.
B. 2-Position Switch The 2-Position Switch toggles the unit between Manual
Operation and Remote Operation.
- Remote (Front Position): The unit is operated with remote control.
- Manual (Back Position): The unit operates with the flames, logs, and ember bed. When the manual control is in the Manual position the heater does not run.
! NOTE: When the manual control switch is in the Manual position, the Log Grate unit will not operate with the remote control.
C. Initialization Button
Used to synchronize the supplied remote control with the Log Grate.
Resetting the Temperature Cutoff Switch
Should the heater overheat, an automatic cutout will turn the heater off and
it will not come back on without being reset. It can be reset by switching the
On/ Off Switch to Off and waiting 5 minutes before switching the unit back on.
**CAUTION: If you need to continuously reset the heater, unplug the
unit and call Dimplex North America Limited at
1-800-668-6663.
Remote Control
The remote control has a range of approximately 50 feet (15.25 m), it does not
have to be pointed at the Log Grate and can pass through most obstacles
(including walls). It is supplied with 243 independent frequencies to prevent
interference with other units.
Battery Installation**
- Depress the tab on the battery cover on the back of the remote control and remove the battery cover.
- Install two (2) AAA batteries into the remote control (included).
- Ensure the Child Lock is in the “unlocked” position (Figure 2).
- Replace the battery cover.
! NOTE: When the “BAT” symbol is present on the remote control it is
recommended to replace the batteries promptly, to maintain full functionality
of the remote/ Log Grate. The remote control has a battery backup time of only
several hours.
Battery must be recycled or disposed of properly. Check with your Local
Authority or Retailer for recycling advice in your area.
Remote Control Initialization/Reprogramming
-
Plug cord into 120 Volt wall outlet.
-
Ensure the On/Off Switch (Figure 1A) (ON) position.
-
Set the 2-Position Switch (Figure 1B) to the Remote position (front position).
-
Press and hold the Initialization Button on the unit (Figure 1C).
-
While holding the Initialization Button, press the Flame/ Heat On/Off button on the remote control.
-
Release the Initialization Button on the unit.
-
Press the Flame/Heat On/Off button to turn the Flame/ Heat function On.
Frequency Interference
If the Log Grate does not respond properly to the remote control, the remote
operating frequency may have to be reset. The remote control can send another
frequency code to the remote control receiver to eliminate interference.
-
Simultaneously press the “Temperature Down” button and the “Flame Speed Down” button on the remote control (Figure 3).
Figure 3 – Remote Control Functions
A. Room Temperature
B. Set Temperature
C. Light Dimmer
D. Flame Speed Control
E. Sleep Timer
F. Flame & Heat On/Off
G. Temperature Down
H. Temperature Up
I. Light Dimmer Down
J. Light Dimmer Up
K. Flame Speed Down
L. Flame Speed Up
M. Sleep Timer Down
N. Sleep Timer Up -
“COD” will appear in place of the sleep timer digits.
-
Release the “Temperature Down” button and the “Flame Speed Down” button.
-
Press the Initialization Button on the unit (Figure 1C).
-
Press the Flame/Heat On/Off Button button on the remote.
Your remote will now have a different frequency communicating with the Log Grate.
Remote Control Functions
(All letter references are to Figure 3)
B. Set Temperature
Press F button ( ) to turn Log Grate on.
Press H to raise the thermostat.
Press G to lower the thermostat.
Press both H and G to change °F to °C.
C. Light Dimmer
Press the F button ( ) to turn the
Flame/Heat on.
Repeatedly press the J or I button to decrease or increase the brightness of
the up lights.
D. Flame Speed
Press the F button ( **) to turn the
Flame/Heat on.
Press the L button to increase the speed of the flame.
Press the K to decrease the speed of the flame.
E. Sleep Timer
The Sleep Timer automatically shuts off the Log Grate after a preset time
(from 30 minutes to 8 hours).
Press the F button ( ) to turn the Log Grate on.
To set the sleep timer press the N button.
Set the timer from 30 minutes through 8 hours. The Log Grate will
automatically turn off when the sleep timer reaches zero (0) minutes.
The Sleep Timer can be canceled at any time by pressing the M button
repeatedly until the sleep timer displays nothing.
****WARNING: Disconnect power before attempting any maintenance or
cleaning to reduce the risk of fire, electric shock, or damage to persons.
F. Flame & Heat On/Off Button
Press the F button ( ) to turn the Flame/Heat function on. When B is higher
then A the heat will come on. To turn the heat off, lower the B so that its
setting is lower than the A. The default temperature setting is 72°F (22°C).
! NOTE:** When using the remote control the heater runs on a thermostat.
Press the H or G buttons to adjust the set temperature. Once the desired set
temperature is reached
the heater will turn off. The heater will cycle on and off to maintain the
desired set temperature.
Child Lock (Figure 2)
- Depress the tab on the battery cover on the back of the remote control and remove the battery cover.
- Move Child Lock tab to the right to lock the remote control.
- Move Child Lock tab back to the left to unlock the remote control.
- Replace the battery cover.
! NOTE: To temporarily unlock the remote control press (in order)
G then H then I.
When the remote control’s backlight has illuminated the Child
Lock is bypassed. When the backlight is off the Child Lock is re-activated.
Maintenance
WARNING: Disconnect power before attempting any maintenance or cleaning
to reduce the risk of fire, electric shock, or damage to persons.
Log Grate Surface Cleaning
Use warm damp cloth only to clean surfaces of the Log Grate. Do not use
abrasive cleaners.
Servicing
An authorized service representative should perform any servicing.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
NO USER-SERVICEABLE PARTS INSIDE
Warranty
ONE YEAR LIMITED WARRANTY
Products to which this limited warranty applies
This limited warranty applies to your newly purchased Dimplex Electric Log
Grate. This limited warranty applies only to purchases made in any province of
Canada except for Yukon Territory, Nunavut, or Northwest Territories or in any
of the 50 States of the USA (and the District of Columbia) except for Hawaii
and Alaska. This limited warranty applies to the original purchaser of the
product only and is not transferable. Products excluded from this limited
warranty light bulbs are not covered by this limited warranty and are the sole
responsibility of the owner/purchaser. Products purchased in Yukon Territory,
Nunavut, Northwest Territories, Hawaii, or Alaska are not covered by this
limited warranty. Products purchased in these States, provinces, or
territories are sold AS IS without warranty or condition of any kind
(including, without limitation, any implied warranties or conditions of
merchantability or fitness for a particular purpose) and the entire risk of
as to the quality and performance of the products is with the purchaser, and
in the event of a defect, the purchaser assumes the entire cost of all
necessary servicing or repair. What does this limited warranty cover and for
how long Products covered by this limited warranty have been tested and
inspected prior to shipment and, subject to the provisions of this warranty,
Dimplex warrants such products to be free from defects in material and
workmanship for a period of 12 months from the date of the first purchase of a
such product.
The limited 12-month warranty period also applies to any implied warranties
that may exist under applicable law. Some jurisdictions do not allow
limitations on how long an implied warranty lasts, so the above limitation may
not apply to the purchaser.
What this limited warranty does not cover This limited warranty does not apply
to products that have been repaired (except by Dimplex or its authorized
service representatives) or otherwise altered. This limited warranty does
further not apply to defects resulting from misuse, abuse, accident, neglect,
incorrect installation, improper maintenance or handling, or operation with an
incorrect power source. What you must do to get service under this limited
warranty
Defects must be brought to the attention of Dimplex Technical Service by
contacting Dimplex at 1-888-DIMPLEX (1-888-3467539), or 1367 Industrial Road,
Cambridge Ontario, Canada N3H 4W3. Please have proof of purchase,
catalog/model, and serial numbers available when calling. Limited warranty
service requires proof of purchase of the product.
What Dimplex will do in the event of a defect
In the event a product or part covered by this limited warranty is proven to
be defective in material or workmanship during the 12-month limited warranty
period you have the following rights:
- Dimplex will in its sole discretion either repair or replace such defective product or part without charge. If Dimplex is unable to repair or replace such product or part, or if repair or replacement is not commercially practicable or cannot be timely made, Dimplex may, in lieu of repair or replacement, choose to refund the purchase price for such product or part.
- Limited warranty service will be performed solely by dealers or service agents of Dimplex authorized to provide limited warranty services.
- The purchaser is responsible for removal and transportation of such product or part (and any repaired or replacement product or part) to and from the authorized dealer’s or service agent’s place of business.
- This limited warranty does not entitle the purchaser to on-site or in-home services. On-site or in-home services may be performed at the purchaser’s specific request and expense at Dimplex’s then-current rates for such services.
- Dimplex will not be responsible for, and the limited warranty services shall not include, any expense incurred for installation or removal of the product or part (or any replacement product or part) or any labour or transportation costs. Such costs shall be the purchaser’s responsibility.
What Dimplex and its dealers and service agents are also not responsible for: IN NO EVENT WILL DIMPLEX, OR ITS DIRECTORS, OFFICERS, OR AGENTS, BE LIABLE TO THE PURCHASER OR ANY THIRD PARTY, WHETHER IN CONTRACT, IN TORT, OR ON ANY OTHER BASIS, FOR ANY INDIRECT, SPECIAL, PUNITIVE, EXEMPLARY, CONSEQUENTIAL, OR INCIDENTAL LOSS, COST, OR DAMAGE ARISING OUT OF OR IN CONNECTION WITH THE SALE, MAINTENANCE, USE, OR INABILITY TO USE THE PRODUCT, EVEN IF DIMPLEX OR ITS DIRECTORS, OFFICERS, OR AGENTS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH LOSSES, COSTS OR DAMAGES, OR IF SUCH LOSSES, COSTS, OR DAMAGES ARE FORESEEABLE. IN NO EVENT WILL DIMPLEX, OR ITS OFFICERS, DIRECTORS, OR AGENTS BE LIABLE FOR ANY DIRECT LOSSES, COSTS, OR DAMAGES THAT EXCEED THE PURCHASE PRICE OF THE PRODUCT. SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO THE PURCHASER.
How State and Provincial law apply This limited warranty gives you specific legal rights, and you may also have other rights which vary from jurisdiction to jurisdiction. The provisions of the United Nations Convention on Contracts for the Sale of Goods shall not apply to this limited warranty or the sale of products covered by this limited warranty.
Technical Support
Technical and troubleshooting support, as well as a list of replacement parts
can be found on
www.dimplex.com/customer_support.
Dimplex North America Limited
1367 Industrial Road
Cambridge ON
Canada N3H 4W3
© 2016 Dimplex North America Limited
www.dimplex.com
Documents / Resources
|
DIMPLEX DLG1058 28-in Premium Electric Fireplace Log
Set
[pdf] Owner's Manual
DLG1058 28-in Premium Electric Fireplace Log Set, DLG1058, 28-in Premium
Electric Fireplace Log Set, Electric Fireplace Log Set, Fireplace Log Set
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>