LG LAIWB4 AI Module for Oven User Manual

LG LAIWB4 AI Module for Oven

Safety Precautions

• Be sure to read the safety precautions before use and installation, and use it correctly.
• This is to protect the safety of users and installers and prevent property damage.
• After reading the user manual, keep it in a place where the user can see it at any time.

Introduce

Summary

LAIWB4 is a module that supports Wi-Fi, Bluetooth wireless communication, refrigerator voice recognition and artificial intelligence processing and is designed to operate independently. It supports multiple interfaces and has the advantage of being able to connect various external devices.
In addition, it has high performance based on CPU and has specialized functions for artificial intelligence, so it can be applied to home appliances that use artificial intelligence. In addition, it provides scalability to connect with various devices, and provides data transfer rates of up to 72 Mbit/s in case of Wi-Fi. It can operate as a single Wi-Fi module or connect to a host via a serial interface. In case of Bluetooth, music streaming function is provided through paring with other devices.

Major Features and Specifications

1. ARM Cortex-A53 Quad
2. WLAN: IEEE 802.11b/g/n 1X1 2.4Ghz (up to 72.2Mbps)
3. Support WLAN TX/RX LDPC
4. Hardware-based AES/TKIP encryption support
5. Supports Bluetooth BDR/EDR/LE 5.0
6. Linux-based integrated SW development environment support
7. TCP/IP Stack support
8. Oven control through server-based natural language voice recognition
9. Input power: DC 5V or 12V
10. Mic. spec: 2Ch. Analog MEMS Mic.1
    
    

Hardware Configuration

Block Diagram

Command Information

SPI communication with Oven Display PCBA via CN606. For other internal communication, refer to block diagram of FIg2-1.

Electrical Characteristics

Absolute maximum ratings

Table 3-1 Absolute maximum ratings. Exceeding one of the absolute maximum ratings will result in poor performance or It can be caused damage.

Electro Static Discharge (ESD)

The LAIWB4 can withstand ESD voltages up to 1000 V Human Body Model (HBM).According to JESD22- A114, JESD22-A115, it can withstand up to 450 V CDM (Charge Device Model).

Recommended Operation Condition

Table 3-2 Recommended operation condition

Current Consumption

This is the data measuring power consumption in a scenario where the voice recognition module is in operation mode and the voice recognition function is used.

Condition : Tamb=25oC, VCC=5V / 12 V
Table 3.4 Power consumption in Normal mode. *Output power value is based on WLAN module’s antenna port Typ. output

+17 dBm
(Tolerance ±1 dBm)| 180 mA

400mA (5V option)

| 11 Mbps, 320MHz, In Case of voice recognition operation.
**Max Output Power*| Typ. Power Consumption| Comments
---|---|---
+17 dBm
(Tolerance ±1 dBm)**| 2,160 mW
2,000mW (5V option)| 11 Mbps, 320MHz, In Case of voice recognition operation.

Antenna Characteristics(WLAN, Bluetooth Antenna)

Condition: antenna port radiation test of WLAN module VCC= 5V / 12 V, Temp= 0 to +70C, covered with shield-can.

Table 3-5 RF Characteristics

Frequency(MHz)| Efficiency (%)| Avg. Gain(dBi)| Peak Gain(dBi)
---|---|---|---
2400| 53.01| -2.76| +1.83
2442| 70.55| -1.52| +2.6
2485| 62.75| -2.02| +1.36

Interface

| Connector type| Description
---|---|---
CN500| 4 pin 2.00 mm pin header| Power Supply
(5V : pin1 or 12V: pin3 with GND : pin4)
CN602| 6 pin 2.00 mm pin header| Extra UART Interface
CN401| 8 pin 2.00 mm pin header| MIC input(2ch)
CN600| 5 pin 2.00 mm pin header| USB Host
CN605| 6 pin 2.00 mm pin header| USB Device
CN403| 7 pin 2.00 mm pin header| SPK out
CN611| 9 pin 2.00 mm pin header| Sensor(GPIO)
CN606| 12 pin 2.00 mm pin header| UART & SPI Interface to connect Oven Display Board
CN601| 3 pin 2.00 mm pin header| UART

Package Characteristics

Mechanical Characteristics of LAIWB4(AI Module) PCB

Standard Compliance

IEEE / IETF

Table 6.1 IEEE Standard

Wi-Fi

Table 6.2 Wi-Fi Standard

Wi-Fi 802.11b with WPA system inter Operability test plan for IEEE 802.11b devices| 802.11b devices with WPA| 2.1
Wi-Fi 802.11g with WPA system inter Operability test plan| 802.11g devices with WPA| 2.0

Bluetooth

Table 6.3 Bluetooth Characteristic

Regulatory Statement (FCC)

FCC Part 15.19 Statements:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference.
2. this device must accept any interference received, including interference that may cause undesired operation.

FCC Part 15.105 statement(Class B)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Part 15.21 statement
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This device must not be co-located or operating in conjunction with any other antenna or transmitter.

Supplier’s Declaration of Conformity
47 CFR § 2.1077 Compliance Information.
Responsible Party – U.S. Contact Information.
LG Electronics USA 1000 Sylvan Avenue Englewood Cliffs New Jersey, United States, 07632.

Regulatory notice to host manufacturer according to KDB 996369 D03 OEM Manual

This module has been granted modular approval as below listed FCC rule parts.

• FCC Rule parts 15C(15.247)

Summarize the specific operational use conditions

• The OEM integrator should use equivalent antennas which is the same type and equal or less gain then an antenna listed below this instruction manual.

RF exposure considerations

• The module has been certified for integration into products only by OEM integrators under the following condition:
• The antenna(s) must be installed such that a minimum separation distance of at least 20 cm is maintained between the radiator (antenna) and all persons at all times.
• The transmitter module must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures.
• Mobile use
  As long as the three conditions above are met, further transmitter testing will not be required. OEM integrators should provide the minimum separation distance to end users in their end product manuals.

Antennas list
This module is certified with the following integrated antenna.

• Max. Antenna gain: 2.6 dBi / Ant. Type: PCB Pattern Antenna

Any new antenna type, higher gain than listed antenna should be met the requirements of FCC rule 15.203 and 2.1043 as permissive change procedure.

End Product Labeling
The module is labeled with its own FCC ID and IC Certification Number. If the FCC ID and IC Certification Number are not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. In that case, the final end product must be labeled in a visible area with the following:
“Contains FCC ID: BEJ-LAIWB4
“Contains IC: 2703N- LAIWB4

Information on test modes and additional testing requirements

• OEM integrator is still responsible for testing their end product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, additional transmitter in the host, etc.).

Additional testing, Part 15 Subpart B disclaimer

• The final host product also requires Part 15 subpart B compliance testing with the modular transmitter installed to be properly authorized for operation as a Part 15 digital device.

Regulatory Statement (ISED)

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

The antenna(s) must be installed such that a minimum separation distance of at least 20 cm is maintained between the radiator (antenna) and all persons at all times.

Final product labeling (IC)
The module is labeled with its own FCC identification and IC certification number. If the FCC ID and IC certification number are not visible when the module is installed inside another device, the external part of the device in which the module is installed must also present a label referring to the module included. In this case, the final product must be labeled in a visible area with the following information: Contains transmitter module IC: 2703N- LAIWB4

Documents / Resources

| LG LAIWB4 AI Module for Oven [pdf] User Manual
LAIWB4, LAIWB4 AI Module for Oven, AI Module for Oven, Module for Oven, Oven
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>